B Series——Cube Model NC546W User Manual V1.
http://www.wansview.com Index 1 INTRODUCTION ...........................................................................................................................4 2 FUNCTION AND FEATURES .....................................................................................................4 3 APPEARANCE AND INTERFACE.............................................................................................5 4 5 6 7 3.1 APPEARANCE ...........................................................
http://www.wansview.com 7.4.2 Time Setting .......................................................................................................................22 7.4.3 Firmware upgrade .............................................................................................................23 7.4.4 Restore Factory Default.....................................................................................................23 7.4.5 User browsing Log........................................................
http://www.wansview.com 1 Introduction The IP Camera combines a high quality digital video camera with network connectivity and a powerful web server to bring clear video to your desktop from anywhere on your local network or over the Internet. Your IP Camera package should contain the following items, If any of the listed items are missing, please contact your reseller from where you purchased the camera for assistance.
http://www.wansview.com 9 Infrared LED for night vision covers 5m area, to realize 24 hours monitoring. 9 Support mobile phone to view 9 Support three level of user authority. 9 Support upgrading online. 9 Manufacture attached a label at the bottom of each IP Camera, it include Device ID, DDNS. When IP Camera is connected to the internet, this URL can be used to visit the device. 9 Manufacture provides free software, support Multi-view, Long time recording, video replay etc.
http://www.wansview.com 3.2 Interface of Equipment Figure 2 1） Power Input Socket: Connect DC adaptor, its output should be 5V power specification. 2） RJ45 Ethernet Socket: RJ45 Ethernet socket is 10/100M self-adjust. The equipment can connect to all kinds of network equipments, such as hub, router, switch, etc. NOTE: Factory setting IP is 192.168.0.178, the http port is 80, the username is admin, the password is 123456.
http://www.wansview.com 4 Network Connecting Figure 5 4.1 Connection Instruction Before visit the IP Camera, you should firstly connect it to the Network, supply the power to it, and check if the light of RJ45 Socket is normal to make sure all of the communication links are fluent. The connection method is like as Figure 5. 1) IP Camera-1 and IP Camera-2 are connected separately to 2 different LANs. 2) And these 2 LANs are already connected to the Internet.
http://www.wansview.com 5 Visit IP Camera from LAN 5.1 Set IP Address The IP addresses of IP Camera and PC should be at the same segment, for Figure 5, the IP Camera-1 can’t be visited. Run the BSearch_en.exe in the CD, click Search button, and then select the IP Camera-1 to reset the IP address, as the Figure 6. Setting Instruction: 9 Please carefully check the “Local PC information” on the top left corner which lists the PC configuration.
http://www.wansview.com Figure 6 If you have the firewall software in your PC, when you run the HSearch_en.exe, it may pop up a window to say if you want to block this program or not, then you should choose not to block. IP Camera by default use fixed IP address 192.168.0.178 and fixed http port 80. If you don’t have this software, you could also press down the reset button to go back the factory setting. Then you could use this defaulted IP address to visit the IP Camera.
http://www.wansview.com Figure 7 5.2 Visit IP Camera We suggest using IE kernel browser to view the video （it can provide more functions）, but user need to install Player before viewing the video. Click “download and install player (first use)” link, it will popup dialogue box as Figure 8, click Run, it will automatically download player and install. Figure 8 After install the plug-ins, click “Mode 1 to view” link in Figure 7 to view the video (video as Figure 9).
http://www.wansview.com Figure 9 1） Menu column There are 2 kinds of menu, one is main menu, and the other is submenu. The main menu lies at the top of the interface, including View, Network, Alarm, Maintain; Submenu lies on the left of the interface, and different main menu is in line with different submenu. 2） Video Displaying Area Video display area is according with resolution, the higher resolution, and the larger display.
http://www.wansview.com These buttons mean start video, stop, monitor, talk, record and snapshot. Click button to choose the functions. 5） PTZ and video control In Pan/Tilt control area, user can control the position according to the arrow sign: up, down, left, right, middle, horizontal cruise, vertical cruise, and stop etc. Means open IO output and Close IO output. User can also set the device frame rate、resolution, brightness, contrast and other parameters.
http://www.wansview.com WAN IP address is allotted by ISP, please make sure it’s an available WAN IP address. As WAN IP address is lack, many WAN IP address are available in limited area. If PC-2 and PC-3 are not in this area, the IP Camera-1 won’t be visited by them. If user wants to put several IP Cameras into WAN, every device should set the port forwarding. In order to distinguish these devices, every device should set a different port.
http://www.wansview.com Figure 12 The third party domain name is realized by analysis manner, the domain name will be displayed in the browser all the time when visit camera. If the port is not 80, the port number should be adding to the domain name with colon. Example: http://robbicam2.3322.org:81 7 Other Settings 7.1 Network Setting 7.1.1 Basic Network Setting The user can also enter the Basic Network Settings to set the IP address except using the search software. See below Figure 13. Figure 13 7.1.
http://www.wansview.com Figure 14 Note: When the device is connected both WIFI and wired, after it starts up, it will firstly connect to the wired network, if it can’t connect to it, then it will change to connect the wifi. The IP address and port is the same, either wireless or wired network. 7.1.3 ADSL Setting User could enable the ADSL Dialup according to the below Figure 15 (The Telecom Operators will assign the user name and password to you when you apply for ADSL service.
http://www.wansview.com 7.1.5 DDNS Setting Please refer to the content in 6.2. 7.1.6 MSN Setting Figure 17 User can apply for a MSN account, put the MSN account and password as shown in Figure 17. There is MSN Friends List. The user can add his MSN friends. When this device is online, it will show up on friends’ MSN. The MSN friends only need to send “url?” to the device’s MSN and the device will send its WAN IP Address to these friends. Then these friends can visit this device by the URL easily. 7.
http://www.wansview.com two pictures. ¾ Send alarm info to the alarm server. Note： this item can not support alarm I/O 3） Scheduler Device will trigger alarm in scheduled time. User can set schedule time to be “all the time”. Please set the system time, time zone, and select the scheduled time. Please refer to the Picture 18. Figure 18 7.2.2 Mail Service Setting The device will send alarm email to the email address was filled in.
http://www.wansview.com Figure 19 Before setting these parameters, please refer the settings of Outlook Express. 7.2.3 FTP Service Setting Figure 20 When alarming, device will snap and send the image to FTP server, please make sure the FTP setting is correct. Above Figure 20 of FTP setting for your reference, click setting to store the setting info and click test to check the setting.
http://www.wansview.com After correct setting FTP server, you can use “upload Image Periodically” function. Even no alarm, device can also send the snap image to FTP periodically. In order to use FTP function, user should apply username and password on the FTP server first. And please apply some storage, and the authority to write and create sub-category into it. 7.2.4 Alarm Server Figure 21 Please confirm if you have connected to alarm server. The alarm message format as follow: GET /api/alarm.
http://www.wansview.
http://www.wansview.com 7.3.2 Multi Device Setting Figure 25 As Figure 25, User can maximum add 9 devices to view the device simultaneously. Click refresh button to check the device in the LAN. When click the device, will popup setting dialogue box and input the device info, as figure 26 and click save. After that, must click submit button to save. Figure 26 7.3.3 Other settings You can choose open or close indicator LED.
http://www.wansview.com Figure 27 7.4 Maintain 7.4.1 Device Information Figure 28 7.4.2 Time Setting If the device is connected to the Internet, you enable the NTP server to correct the time and select the right time zone. Or you should use the PC’s time to correct its time.
http://www.wansview.com Figure 29 7.4.3 Firmware upgrade The device runs 2 kinds of programmer, one is system firmware, the other is application firmware. They could be upgraded separately. Figure 30 7.4.4 Restore Factory Default Click “Restore Factory Default”, it will pop up a dialogue to confirm if you really want to restore the factory default. After confirmation, the system will restore the factory default and reboot. 7.4.
http://www.wansview.com 8 Centralization Control Figure 32 IPCMonitor is a free software offered by factory, several devices on LAN and WAN can be browsed at the same time. The software also supports snap, video record, alarm and so on. The below Figure 32 is the interface. For more information, pls. refer to the <> in CD.
http://www.wansview.com Network Other Features Basic Protocol TCP/IP、UDP/IP、HTTP、SMTP、FTP、DHCP、 DDNS、UPNP、NTP、PPPOE Other Protocol 802.
http://www.wansview.com The default is infrared lens, when visit outdoor or strong infrared light scenes, there are color differences, the color is not accordance to the real scenes. User can change it to color lens to solve this problem, but color lens can only use under the daylight situation. 4) Can’t find equipment via search software after connect to LAN Make sure the equipment and PC is in the same LAN; if install firewall software, please close it and try again.
http://www.wansview.com 11 FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
