B Series——Robot Model IP Camera 2011-7 V4.
IP CAMERA User Manual Index 1 2 3 INTRODUCTION ........................................................................................................................... 4 1.1 THE PACKAGE INCLUDES .......................................................................................................... 4 1.2 FUNCTION AND FEATURES ........................................................................................................ 4 1.3 TECHNICAL PARAMETERS ......................................
IP CAMERA User Manual 5.4.1 Device Information ............................................................................................................ 20 5.4.2 Time Setting ....................................................................................................................... 20 5.4.3 Firmware upgrade ............................................................................................................. 20 5.4.4 Restore Factory Default .....................................
IP CAMERA User Manual 1 Introduction The IP Camera combines a high quality digital video camera with network connectivity and a powerful web server to bring clear video to your desktop from anywhere on your local network or over the Internet. 1.1 The package includes IP Camera * 1 IP Camera Utility CD *1 5V Power Adapter *1 Stand of plastic * 1 Cable * 1 NOTE:If you select the device with wifi function, it has built-in wifi module and transmitting antenna in package. 1.
IP CAMERA User Manual 1.3 Technical Parameters Item Image Capture Pan/Tilt Assistant Video and Audio Network Other Features Hardware Interface Physical Index Sub Item Description Sensor CMOS sensor Total of pixel 300k Minimum illumination IR on,0 Lux Lens f=3.6mm, F=2.
IP CAMERA User Manual temperature Software(PC Side) OS Supported Microsoft Windows 98/2000/XP/Vista/7 etc. Browser Internet Explorer6.0 and Above or Compatible Browser, Firefox, Safari etc. Application Software IPCMonitor.exe 2 Appearance and interface 2.
IP CAMERA User Manual 3 Visit IP Camera from LAN 3.1 Lan connection Figure 3 3.2 Search and set the ip address of the ip camera Run “BSearch_en.exe” in the CD, the setting interface as figure 4. Figure 4 Operation Steps: 1) Click “Search (F3) 2) Choose the device 3) Change the ip address of the ip camera according to the information in the red frame on the left. The numbers in the red circle should not be the same.
IP CAMERA User Manual is: admin, password is: 123456). 5) Click “Update” 6) After successfully update, click “Search (F3)”, choose the device and click “Browse (F4)”. Then you may view the ip camera, like figure 5. NOTE: 1) If you don‟t know how to fill out the content of “IP config”, you could also tick the “Set IP automatically” to get the IP address from the router automatically. 2) If you have the firewall software in your PC, when you run the BSearch_en.
IP CAMERA User Manual 3.3.1 Video Play Area After install the plug-ins, click “Mode 1 to view” link in Figure 5 to view the video (video as Figure 7).
IP CAMERA User Manual Figure 8 4) PT and video control In Pan/Tilt control area, user can control the position according to the arrow sign: up, down, left, right, middle, horizontal cruise, vertical cruise, and stop etc. Means open IO output and Close IO output. User can also set the device frame rate、resolution, brightness, contrast and other parameters. 4 Visit IP Camera from WAN 4.
IP CAMERA User Manual 4.2 Port forwarding If visit IP Camera from WAN, you must do port forwarding on the router. Take Netgear router for example.
IP CAMERA User Manual figure 11. Figure 11 4.3.2 Third Party DDNS User can also use third part DDNS, such as www.dyndns.com User must apply a free domain name from this website and fill the info into the below blanks (Figure 12) and save the settings. Then the domain name can be used. Figure 12 Note: Using the third party domain name, if the http port is not 80, the port number should be adding to the domain name with colon. Example: http://btest.dyndns.biz:81.
IP CAMERA User Manual data of the selected wireless network will be shown in the following blanks. Put in the password and click “Set”, then the WIFI setting is finished. Figure 14 Note1: When the device is connected both WIFI and wired, it will firstly connect to the wired network, if it can‟t connect to it, then it will change to connect to the wifi. The IP address and port is the same, either wireless or wired network.
IP CAMERA User Manual Before using UPNP function, please make sure the router‟s UPNP function has been triggered. Not all the routers support UPNP perfectly. Please test if the router works well with the equipment, if not, we would suggest you to disable this function and do the port-forwarding manually. 5.1.5 DDNS Setting Please refer to the content in 4.3. 5.1.6 MSN Setting Figure 17 User needs to apply for a MSN account for this device first, for example: test1@hotmail.com.
IP CAMERA User Manual choose “close”. Figure 18 2) Alarm Action All kinds of alarm modes: IO interface for alarm signal output: when relay is switched on, the external alarm will begin to alarm. Send alarm info by email. Send the site pictures to the FTP server, user can also set the break time between two pictures. Send alarm info to the alarm server. 3) Scheduler Device will trigger alarm in scheduled time. User can set schedule time to be “all the time”.
IP CAMERA User Manual Figure 19 5.2.
IP CAMERA User Manual The device will send alarm email to you. You only need to fill out the blanks with your email address as shown in Figure 20. After the setting, please click save and test to check if it works properly. If it is properly set, user can tick to enable “Report Internet IP by mail”. After every restart, the device will send its Internet IP address to user‟s email address. 5.2.
IP CAMERA User Manual userpwd=password& rea=alarm type (1=Motion Detection, 2 =Alarm from Alarm in port)& io=0 Alarm server needs developing by user. User can extend other functions on this server, like SMS, MMS alarm, and mobile phone etc. 5.3 Advanced 5.3.1 User Setting There are three levels of authority; they are Administrator/Operator/Visitor. Administrator have the highest authority, it can do any change to the settings.
IP CAMERA User Manual Figure 24 As Figure 24, User can maximum add 9 devices to view the device simultaneously. Click refresh button to check the device in the LAN. When click the device, will popup setting dialogue box and input the device info, as figure 25 and click save. After that, must click submit button to save. Figure 25 5.3.3 Other settings You can choose open or close indicator LED. If set PTZ center on start „Yes‟, when start device, Pan/Tilt will move to center and then stop.
IP CAMERA User Manual 5.4 Maintain 5.4.1 Device Information Figure 27 5.4.2 Time Setting If the device is connected to the Internet, you enable the NTP server to correct the time and select the right time zone. Or you should use the PC‟s time to correct its time. Figure 28 5.4.3 Firmware upgrade The device runs 2 kinds of programmer, one is system firmware, the other is application firmware. They could be upgraded separately. Figure 29 5.4.
IP CAMERA User Manual and reboot. 5.4.5 User browsing Log After enter the log interface, you could view who and when the device is visited. Figure 30 6 Centralization Control Figure 31 IPCMonitor is a free software offered by factory, several devices on LAN and WAN can be browsed at the same time. The software also supports snap, video record, alarm and so on. The below Figure 31 is the interface. For more information, pls. refer to the <> in CD.
IP CAMERA User Manual adapter for this equipment. 2) Slowly browse speed This equipment adopts MJEPG compression format, it needs large network bandwidth, the narrow bandwidth will affect the browse speed. The typical bandwidth uses situation as below: 640x480@10fps : 4.0 Megabits ~ 5.0 Megabits 320x240@30fps : 1.2 Megabits ~ 1.
IP CAMERA User Manual 8 FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.