GENERAL INFORMATION Main Features For your Safety Unpacking General Operation RCU 3 3 4 5 6 7 INSTALLATION Rear Panel Connecting to TV& VCR using SCART support Connecting to TV using RCA support Connecting to Digital Amplifier MENU INFORMATION Main Menu 1. Channel List 1.1 TV Channel List 1.2 Radio Channel List 1.3 Delete All 2. Installation 2.1 Antenna Connection 2.2 Satellite List 2.3 Antenna Setup 2.4 Single Satellite Search 2.5 Multi Satellite Search 2.6 TP List 3. System Setup 3.1 Language 3.2 TV 3.
4. Tools 4.1 Information 4.2 Factory Setting 4.3 Upgrade by USB 4.4 Common Interface 4.5 Conditional Access 4.6 USB 5. Game 6. REC 6.1 Record Mangager 6.2 HDD Information 6.3 HDD Format 6.4 PVR Setting 7. Hot key 7.1 Info 7.2 EPG 7.3 Find 7.4 Numer 7.5 TV/Radio 7.6 Up/Down 7.7 Left/Right 7.8 Mute 7.9 Pause 7.10 OK 7.11 Audio 7.12 Recall 7.13 Fav 7.14 Teletext 7.
A Digital Satellite Receiver is a convenient product that allows you to view a variety of programs provided through satellite. This user's guide covers the installation of the DSR and the necessary steps to implement various features. This also explains special features available only in this DSR in detail, which will allow you to make full use of these feature. Information confirmed in this document is subject to change.
For Your Safety To avoid electric-shock hazards, do not open the cabinet, refer servicing to qualified personnel only. Keep the receiver away from flower vases, tubs, sinks, etc., in order to avoid damaging the equipment. Do not expose the receiver un-der the sunlight. And keep it away from the heat source. Do not block ventilation holes of the Receiver so that air can circulate freely. When the abnormal phenomenon occur, you should cut off the power immediately.
Warning statement Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment . NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Remote Control Batteries Guide General Operation Throughout this manual you will notice that the everyday operation of the receiver is based on a series of user friendly on screen display and menus. These menus will help you get the most from your receiver, guiding you through installation, channel organizing, viewing and many other functions. All functions can be carried out using the buttons on the RCU, and some of the functions can also be carried out using the buttons on the front panel.
RCU Key Function Turns power ON/OFF of the DSR When watching a channel, mute the sound 0~9 TV/RADIO PR FAV Enter number of the required menu item or select a channel number to watch Switches between TV and Radio mode Switches back to previous channel Displays the favorite group list SHIFT Timeshift function key FIND Display the Find window INFO Show information of the current channel MENU Press this key one time to run menu onscreen Moves up / down a page in the list OK, LIST PR+, PR- EXIT E
Rear Panel Front Panel Rear Panel LNB IN: CONNECT TO SATELLITE ANTENNA LNB OUT:CONNECT TO THE OTHER RECEIVER CONNECT TO A PC FOR S/W UPGRADE CONNECT TO TV/VCR USING A SCART CABLE CONNECT TO TV SET HDMI-OUT INPUT POWER ON/OFF CONNECT VIDEO TO TV USING RCA JACK CONNECT TO AUDIO R/L TO TV OR AUDIO TUNER CONNECT TO A DIGITAL AMPLIFIER RF OUT: CONNECT TO TV ANT INPUT Connecting to TV using SCART support Satellite Dish DSR IN TV SCART
Connecting to TV using RCA support Satellite Dish IN VIDEO AUDIO TV R L Connecting to Digital Amplifier Satellite Dish IN TV DIGITAL AUDIO CONVERTOR OR AMPLIFIER SPEAKER L R DIGITAL AUDIO
Main Menu Make sure that you have properly installed and connected the cables of the receiver . If the receiver is the factory status or there is no program list, when power on, the Main Menu window will be displayed on the screen. During the normal TV/Radio mode, press MENU key on the RCU to enter into the Main Menu window. This menu consists of 6 major main menus as follow.
If there is no program, you can not exit from the Main Menu window by pressing MENU or EXIT key. System will inform "No channel" and the following items turn grey.
3. Press FAV key to move the FAV button upward. Select the program and press OK key to pop up the favourite group list. In the list, select the group that you want to add into and press OK key, and then you will find the favourite mark is displayed at the right side of the selected program. Press FAV key again to exit from the fav mode, and you will find the FAV button return to the origin position. 4. Press red colour key to move the Lock button upward.
i . Sort (red colour key) Press red colour key to pop up the Sort drop-down list. Name(A-Z): The ascending order, omitting the $ character, the number is ahead, then the capital letter, at last the lowercase. Name (Z-A): The opposite order of the above Name (A-Z). Free/Scramble: All FTA programs are listed ahead, while all scrambled programs are listed last. Lock: all locked programs are listed at the last. Default ii. Edit (green colour key) Press green colour key to move the Edit button upward.
iii. Delete (blue colour key) In Delete window, press blue colour key to move the Delete button upward. Select the program and press OK key to mark this program with the deletion mark. You can cancel this mark by pressing OK key again. Press EXIT key to pop up the dialogue "Are you sure to save?". Select Yes button and press OK key to save, or select NO button and press OK key to exit without saving. 1.2 Radio Channel List Sine the same operation as 1.1 TV Channel List, here we don't explain any more. 1.
2.2 Satellite List 1. Press PR+, PR- keys to select the satellite up or down. Press OK key to select and mark, and you can press OK key again to cancel the selection and the mark. 2. If there is no satellite, the red colour and blue colour keys will be invalid. 3. Press red colour key to pop up the Edit Satellite window. Press PR+, PR- keys to move cursor up or down. Name: User numeric keys to change the name of the satellite, please refer to the Edit Channel Name.
2.3 Antenna Setup Part A: Fixed Suppose that you have selected Fixed Antenna in the Antenna Connection window. 1. Satellite: All selected satellites in the satellite list are displayed in this item. Press keys to select the satellite in circle. Or press OK key to pop up the drop-down list, then select the desired satellite in the list and press OK key to confirm. 2. LNB Freq, Transponder, DiSEqC1.0, DiSEqC1.1: The same operation as the above. 3.
Position No., & Save: The range is from 0 to 63. "0" delegates the original position. You can select the proper value when you has rotated the antenna. Go to X: Press OK key to pop up the drop-down list, select the proper position (reference or from 1to 63) to realize the selected position. West East: Press key to turn west, while press key to turn east. Press OK key to pop up the dialogue "Are you sure to change this satellite's position?".
7. Motor Setting: Press OK key to enter into the Motor setting window. Satellite, Transponder: Press keys to select satellite or transponder, or press OK key to pop up the drop-down list and select in the list. 2.4 Single Satellite Search 1. Satellite : Press keys to select the satellite in circle. Or press OK key to pop up the drop-down list, then select the desired satellite in the list and press OK key to confirm. 2. FTA Only: Press keys to select between Yes and No. 3.
4. Network Search: Select between No and Yes. This item turns grey when Auto Scan is selected in the following Scan mode item. 5. Scan Mode: Press keys to select between Auto Scan and Preset Scan. Auto Scan is Blind scan, while Preset Scan is to search the preset frequencies. 6. Search: Press OK key to start searching. 2.6 TP List 1. Press PR+,PR- keys to select the proper satellite. 2. Press red colour key to pop up the Edit TP window. Frequency, Symbol rate: Press keys to add or reduce by step one.
4. Press yellow colour key to pop up dialogue " Are you sure to delete?". Press OK key at the Yes button to delete the selected TP, or press EXIT key to cancel the operation. 5. Press blue colour key to pop up the TP Search window. FTA only, Scan Channel, Network Search: Press keys to select the proper option. Press OK key at the OK button to start searching. 3. System Setup 1. Press OK key or key to move the cursor to the right menu. 2. Press PR+, PR- keys to move the cursor up or down. 3.
3.2 TV Press PR+, PR- key to move the cursor up or down, while press keys to change the setting and the setting will take effect immediately. 1. Display Mode: Select among Auto,PAL, PAL-M, PAL-N, NTSC. 2. Aspect Mode: Select among 4:3LetterBox, 4:3PanScan, 16:9. 3. Video Output: Select between RGB and CVBS. 4.RF System: Select among PAL,PAL- M,PAL-N,NTSC and Auto. 5.RF Channel:PAL:21-69,NTSC:14-83. 6. DV-OUT: Select among 480i/576i, 480P/576P, 720P and 1080i. 3.3 Local Time Setting 1.
2. Timer Service: Select between Channel and Message. If Channel is selected, the Wakeup Channel is displayed in the following item. If Message is selected, the Wakeup Message is displayed in the following item. In wakeup message, you can select among Birthday, Anniversary, General. At the same time the duration item turns grey. 3. Wakeup Date, On Time: Use numeric keys to input the valid date. Duration: Set the gap time. After waking up, system will power off automatically after the duration time.
3.7 Favorite There are 32 favorites group listed in this window. Press PR+, PR- keys to select one and press OK key to the Rename window. Since the same operation as the above the Add Satellite window, here we don't explain any more. 3.8 Other 1. LNB Power: Select between Off and On. 2. Channel Play Type: Select among All, Free, Scramble. 3. Channel Change: Select between Freeze and Black screen. 4. Beeper: Select between Off and On. 4. Tools 1.
4.2 Factory Setting Press OK key to enter into the Factory Setting window. Select Yes button and press OK key to return to the factory setting. All searched channels and set information will be erased. Select No button and press OK key to cancel this operation, or press MENU or EXIT key to cancel and exit. 4.3 Upgrade by USB 1.Upgrade File: Show the Upgrade File. 2.Upgrade Mode: Select between AllCode and Dump.
Product Ordering Not avaliable in this software. Subscription Status Know the detail information of Subscription Status. PPV Status No Entitlement. Tokens Status Know the detail information of Tokens Status. Change CA PIN Changes CA PIN window is designed for changing the smart card's PIN, which is required if you want change the maturity level settings. In order to change the PIN, you must know the current PIN also called the old PIN.
Modem Ordering Not Modem available. About Conax CA Know the information about Conax CA. Message All messages are listed in this window. Language Show all the language you can select. Loader Status You can select allow download or forbid download. 4.5 Conditional CA Select Conditional CA item and press OK key, then you will enter into its submenu which consists four items of About CA Info, Change PIN, Change Signature PIN, Maturity Level. 4.5.
4.5.3 Change Signature PIN Do the same way as the above Change PIN. Note: The signature PIN will be locked after the three erroneous attempts to enter the correct PIN. If locked, please call the dealer for help. 4.5.4 Maturity Level Input the PIN then Move cursor to Select Maturity level,you can select AOver18,X-Erotic,G-General audience,PG-Parental Guidance,move cursor to Change Maturity level button and press OK key,and then system will pop up a dialogue informing you the changing result. 4.
Image view operation Please see the below image operation menu if Image function is selected. 1.Red Key: Start to browse image if press RED key, or play the selected image if press OK key, return to USB File list if play is over, or return by press Exit Key. 2.Yellow Key: Delete selected image if press Yellow Key. 3.
5.Press [Play] key to preview. Press [OK] to play the recorder in full screen as below picture. 6.Press [Pause] key to pause. Press [Pause] key repeatedly to realize the step function. Press / key to fast Forward or fast backward. Press / key to slow forward or slow backward . 6.2 HDD Information Show you the information in windows as besides. 6.3 HDD format Press OK at the HDD Format button to pop up the dialogue Are you sure to format the disc? You can select Yes or No. 6.4 PVR Setting 1.
7.2 EPG Press EPG key to enter into the EPG window. 1. Press PR+, PR-, keys to select up or down, left or right. 2. Press red colour key to pop up the Time Bar window. Press PR+, PR- keys to select up or down, while press keys to select left or right in the time bar. : Press OK key at this button to return to the EPG window. : Press OK key at this button to move the cursor to the current time line. : Press OK key to push the time forward or backward by half an hour.
7.5 TV/RADIO In normal mode, press TV/RADIO key to switch between TV mode and Radio mode. 7.6 Up/Down (Channel Change) Press PR+, PR- keys to change the channel up or down. If in the all satellites group, you can select channel in all searched channels. If in the specific satellite, only can select channel in the satellite group. 7.7 Left/Righ (Volume+/-) Press keys to change the volume. Press while press keys to decrease the volume, keys to increase the volume. 7.
7.12 Recall Press key to switch the current channel to the previous channel. 7.13 FAV 1. Press FAV key to pop up the favourite group window. 2. Press keys to select the favorite group. Press PR+, PR- keys to select the channel up or down. Press OK key at the selected channel to view it in full-screen. Press MENU or EXIT key to exit. 3. If there is no favorite channel, system will inform " No FAV Channel!" when you press FAV key. 7.14 Teletext Press TXT key to open the teletext on the screen.
Problem Possible causes What to do The display on the front panel does not light up. Main cable is not connected. Check that the main cable is plugged into the power socket. No sound or picture, but the front panel shows red light. The receiver is in standby mode. Press the standby button. The satellite dish is not pointing at the satellite. Adjust the dish. Check the signal level in the Antenna Setup menu. No signal or weak signal.