GENERAL INFORMATION Main Features For your Safety Unpacking General Operation RCU INSTALLATION Front Panel Rear Panel Connecting to TV using RCA support Connecting to Digital Amplifier MENU INFORMATION Main Menu 1. Channel List 2. Installation 3. System Setup 4. Tools 5. Game 6.
A Digital Satellite Receiver is a convenient product that allows you to view a variety of programs provided through satellite. This user's guide covers the installation of the DSR and the necessary steps to implement various features. This also explains special features available only in this DSR in detail, which will allow you to make full use of these features. Information confirmed in this document is subject to change.
When the abnormal phenomenon occur, you should cut off the power immediately. Do not expose the receiver un-der the sunlight. And keep it away from the heat source. To avoid electric-shock hazards, do not open the cabinet, refer servicing to qualified personnel only. Do not touch the receiver during thunder, since that might create electric-shock hazards. Do not block ventilation holes of the Receiver so that air can circulate freely. Keep the receiver away from flower vases, tubs, sinks, etc.
Warning statement Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment . NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
(Optional) Remote Control General Operation Batteries User's Gudide Throughout this manual you will notice that the everyday operation of the receiver is based on a series of user friendly on screen display and menus. These menus will help you get the most from your receiver, guiding you through installation, channel organizing, viewing and many other functions.
RCU Key 0~9 TV/RADIO Function Turns power ON/OFF of the DSR When watching a channel, mute the sound Switches between TV and Radio mode Enter number of the required menu item or select a channel number to watch Display the favorite group list Switches back to previous channel FAV Display the satellite list PR SAT Show information of the current channel Display the Find window INFO Press this key one time to run menu onscreen Display the Audio window.
Rear Panel Front Panel Rear Panel LNB IN: CONNECT TO SATELLITE ANTENNA LNB OUT:CONNECT TO THE OTHER RECEIVER CONNECT TO 12V TO AN EXTERNAL 0/12V SWITCH CONNECT TO A PC FOR S/W UPGRADE POWER ON/OFF CONNECT VIDEO TO TV USING RCA JACK CONNECT TO AUDIO R/L TO TV OR AUDIO TUNER CONNECT TO A DIGITAL AMPLIFIER RF IN: CONNECT TO CABLE SINGAL RF OUT: CONNECT TO TV ANT INPUT
IN VIDEO AUDIO R L Connecting to TV using RCA support TV DSR Connecting to Digital Amplifier DSR DIGITAL AUDIO L R Satellite Dish Satellite Dish DIGITAL AUDIO CONVERTOR OR AMPLIFIER SPEAKER
Main Menu Make sure that you have properly installed and connected the cables of the receiver well. If the receiver is the factory status or there is no program list, when power on, the Main Menu window will be displayed on the screen. During the normal TV/Radio mode, press MENU key on the RCU to enter into the Main Menu window. This menu consists of 5 major main menus as follow. - Edit Channel - Installation - System Setup - Tools - Game mark.
If there is no program, you can not exit from the Main Menu window by pressing Sub-menu Turn grey when there is no program Othello Sudoku Other MENU or EXIT key. System will inform "No channel" and the following items turn grey.
3. Press FAV key to move the FAV button upward. Select the program and press OK key to pop up the favourite group list. In the list, select the group that you want to add into and press OK key, and then you will find the favourite mark is displayed at the right side of the selected program. Press FAV key again to exit from the fav mode, and you will find the FAV button return to the origin position. 4. Press red colour key to move the Lock button upward.
6. Press yellow colour key to move the Move button upward. Select the program and press OK key to mark this program with the move mark. Press PR+, PR- keys to move the cursor to the position where you want to locate and press OK key to confirm. Press yellow colour key again to exit from the yellow mode, and you will find the yellow button return to the origin position. 7. Press blue colour key to enter into the Edit channel window. i .
ii. Edit (green colour key) Press green colour key to move the Edit button upward. Select the program and press OK key to pop up the Rename window. In Rename window, press red colour key to switch between capital letter and lower letter; keys to press green colour key to delete the character on the cursor; press move the cursor left or right; press numeric refer to the down table.
In Edit Channel window, press blue colour iii. Delete (blue colour key) key to move the Delete button upward. Select the program and press OK key to mark this program with the deletion mark. You can cancel this mark by pressing OK key again. Press EXIT key to pop up the dialogue "Are you sure to save?". Select Yes button and press OK key to save, or select NO button and press OK key to exit without saving. 1.2 Radio Channel List Sine the same operation as 1.
2. Installation 1. Press OK key or you can not key to pop up the "Input Password" dialogue, enter into the menu unless the correct password is inputted. The default password is "0000". key to move the 2. Press PR+, PR- keys to move the cursor up or down. 3. Press EXIT key or focus to the left menu. keys to select between Motor 2.1 Antenna Connection Press Antenna and Fixed Antenna. 2.2 Satellite List Press OK key to select and 1. Press PR+, PR- keys to select the satellite up or down.
3. Press red colour key to pop up the Edit Satellite window. Press PR+, PR- keys to move cursor up or down. Name: User numeric keys to change the keys to name of the satellite, please refer to the Edit Channel Name. Longitude: You can press switch between east longitude and west longitude. After pressing OK key, you can use numeric keys to edit the longitude, press EXIT key or the PR+, PR- keys to exit editing mode. The range of the longitude is from 1to 180 degree.
2.3 Antenna Setup Part A: Fixed Suppose that you have selected Fixed Antenna in the Antenna Connection window. 1. Satellite: All selected satellites in the keys to select the satellite in satellite list are displayed in this item. Press circle. Or press OK key to pop up the dropdown list, then select the desired satellite in the list and press OK key to confirm. 2. LNB Freq, Transponder, DiSEqC1.0, DiSEqC1.1: The same operation as the above. keys to select in circle. 3.
keys to select the 4. Motor Setting: Press OK key to the Motor Setting window. Satellite: Press satellite in circle. Or press OK key to pop up the drop-down list, then select the desired satellite in the list and press OK key to confirm. Transponder: The same operation as the Position No., & Save: The range is from 0 to 63. "0" delegates the original position. above. You can select the proper value when you has rotated the antenna. key to turn east.
6. If select USALS, Delete All item will turn grey. keys to switch between keys to switch between West and Local Longitude, Local Latitude: Press East, or press North and South. Press OK key to enter into the editing mode. Use numeric keys (0-9) to input the longitude or latitude, press MENU key or EXIT key to exit. The range of the longitude is from 0 to 180,while the range of the latitude is from 0 to 90.
4. Network Search: Select between No and Yes. This item turns grey when Auto Scan is keys to select selected in the following Scan mode item. 5. Scan Mode: Press between Auto Scan and Preset Scan. Auto Scan is Blind scan, while Preset Scan is to search the preset frequencies. 6. Search: Press OK key to start searching. 2.5 Multi Satellite Search From the Multi Satellite Search window, you can search several satellites at the one time. 1.
2. Press red colour key to pop up the Edit TP window. the desired keys to add or reduce by step one. Or press Frequency, Symbol rate: Press numeric keys (0-9) to input value. The range of the frequency is 300013450, while the range of the symbol rate is 1000~45000. The inputted value is beyond keys to switch between this range, the value will return to the origin value. Polarity: Press Vertical and Horizontal. 3. Press green colour key to pop up the Add TP window.
3. System Setup 1. Press OK key or cursor to the right menu. key to move the key to move the 2. Press PR+, PR- keys to move the cursor up or down. 3. Press EXIT key or focus to the left menu. 3.1 Language keys to select the 1. Press OK key to enter into the Language window. Press language in circle, while press PR+, PRkeys to move the cursor up or down in circle. 2. Press MENU key or EXIT key to save and exit. 3. The types of the language, pleaser refer to the configuration of the customer. 3.
3.3 Local Time Setting 1. Summer Time: Select between ON and OFF. "OFF" delegates the normal time. If select ON, time will add one hour. 2. GMT Offset: When select "ON" in GMT Usage item, system will get the date and time information from the screen automatically. Date and Time two items will turn grey. Select the proper option in the GMT Offset item. The default setting is GMT ON. 3.Date, Time: When select "OFF" in GMT Usage, Date and Time two items take effect, while GMT Usage turns grey.
Duration: Set the gap time. After waking up, system will power off automatically after the duration time. Press MENU or EXIT key to save and exit. 3.5 Parental Lock Before entering into the Parental Lock keys to select window, you need input the correct password. The default password is 0000. 1. Menu Lock: Press between Off and On. If select "On" , you can keys to select not enter into the most window before entering the password. 2. Channel Lock: Press between Off and On. The default value is Off.
3.7 Favorite There are 32 favorites group listed in this window. Press PR+, PR- keys to select one and press OK key to the Rename window. Since the same operation as the above the Add Satellite window, here we don't explain any more. 3.8 Other 1. LNB Power: Select between Off and On. Free, Scramble. 2. Channel Play Type: Select among All, 3. Channel Change: Select between Freeze and Black screen. you can not key to pop up the 4. Beeper: Select between Off and On. 4. Tools 1.
4.1 Information Press OK key to the Information window. 4.2 Factory Setting Press OK key to enter into the Factory Setting window. Select Yes button and press OK key to return to the factory setting. All searched channels and set information will be erased. Select No button and press OK key to cancel this operation, or press MENU or EXIT key to cancel and exit. 4.3 SatcoDX Auto Programing Press OK key at the Start button to start key to enter into the receiving date from RS232 for 10 seconds. 5.
6. Hot Key 6.1 Info Press INFO key to pop up the Info bar. Press INFO key again to pop up the program guide of the current program. You can press keys to know the program guide of the future 16 days. keys to select up Press EPG key to enter into the EPG window. 6.2 EPG 1. Press PR+, PR-, or down, left or right. 2. Press red colour key to pop up the Time keys to select Bar window. Press PR+, PR- keys to select up or down, while press left or right in the time bar.
keys to select the 3. Detail Information: In the EPG window, press PR+, PRchannel and program, and press OK key to know the detail information of the current program. You can add the current 4. Press green colour key to enter into the Timer window. program to the Timer. If 8 timers is already, system will inform "Timer is full!'. 6.3 Find window. Use numeric keys to enter into the Press FIND key on to pop up the Find character and use the colour keys to realized the corresponding operation.
Press 6.8 Mute keys to open the volume. key to close the volume. You can press volume, or press 6.9 Pause key once again to restore the During the viewing, you can press PAUSE key to stop the picture while the volume continues. You can play the picture by pressing PAUSE key once again. 6.10 OK 1. During the viewing or listening, press OK key to pop up the TV program list or the Radio program list. 2.
6.13 FAV keys to select the favorite 1. Press FAV key to pop up the favourite group window. 2. Press group. Press PR+, PR- keys to select the channel up or down.. Press OK key at the selected channel to view it in full-screen. Press MENU or EXIT key to exit. 3. If there is no favorite channel, system will inform " No FAV Channel!" when you press FAV key. 6.14 Teletext Press TXT key to open the teletext on the screen. If there is no teletext, system will inform "No Teletext Data". Press EXIT key to exit.
The LNB is faulty. LNB noise factor too high. Satellite dish is too small. Signal is too strong. The satellite dish is not pointing at the satellite. No signal or weak signal. The satellite dish is not pointing at the satellite. The receiver is in standby mode. Main cable is not connected. Check the UHF channel fixed in your system and tune the UHF channel properly. Change the LNB. Change to an LNB with lower noise factor. Change to a larger dish. Connect a signal attenuator to the LNB input.