X XT-BL10 Prod duct Specifiication —— —2.4GHz Wi-Fi and BL LE coexisteence Modu ule Ver : 1.0 Date: June.3,2021 Feeatures General SPI * 1; EN * 1; PWM M *5; 10-bit DAC * 1; 12-bit ADC*1 SDIO O 2.0 * 1; Chip:: BL602 Moduule Size:16mm m*20mm*3m mm Compplete 802 .111 b/g/n solutiion for 2.
Update Record Date Version Update 2020-8-25 V1.0 First released 2021-6-3 V2.
Table of Contents 1. Introduction ....................................................................................................................... 1 2. Interface Definition ........................................................................................................... 3 3. Size and Layout ................................................................................................................. 5 4. Electronical Characteristics .......................................................
XT-BL L10 User Mann nual 1.. Introdu uction XT-BL10 W Wi-Fi and BLE coexisstence Moddule is a hig ghly integraated single--chip low power p 802.111n Wireless W LAN N (WLAN) network co ontroller. Itt combines an RISC CPU C , WLA AN MAC, a lT1R capaable WLAN W basebband, RF, annd Bluetootth in a singgle chip. It also a providees a bunch of configurrable GPIO,, w hicch are confiigured as diigital periph herals for di fferent appllications and control ussage.
XT-BL10 User Mannual Technical parameters for XT-BL10 are listed as follows. Table 1.1 XT-BL10 Parameters Types Items Parameters Frequency 2.4G~2.5G(2400M~2483.5M) 802.11b: 19 ±1dBm Transmit power 802.11g: 19 ±1dBm 802.11n: 19 ±1dBm Wi-Fi 802.11b: -91 dbm (11Mbps) Receiver sensitivity 802.11g: -77 dbm(54Mbps) 802.11n: -73 dbm(MCS7) EVM <-28dB @802.11g <-28dB @802.11n Antenna PCB antenna CPU 32-bit RISC CPU Interface UART/SDIO/SPI/I2C/GPIO/PWM Working voltage 3.0V ~ 3.
XT-BL L10 User Mann nual 2.. Interface Defin nition XT-BL L10 modulee interface definition d is shown as below。 b Fig. 2.1 XT-BL10 Pin P Definitiion Workingg mode and pin functio on is shownn in Table 2.1. 2 Table 22.1 Working mode Mode GPIO8 UART Download D M Mode High Flash h Boot Modee Low Table 2.2 P Pin Function n Definition n Num Pin Nam me Type Functtion 1 GPIO8 I/O SPI, I2C, U UART, PWM M, AUXADC C, GPIO.
XT-BL10 User Mannual 4 GPIO16 I/O SPI, I2C, UART, PWM, GPIO 5 GPIO11 I/O SPI, I2C, UART, PWM, AUXADC, GPIO,*Low-High when Reset 6 GPIO12 I/O SPI, I2C, UART, PWM, AUXADC, GPIO 7 GPIO14 I/O SPI, I2C, UART, PWM, AUXADC, GPIO 8 GPIO20 I/O SFLASH, SPI, I2C, UART, PWM, GPIO 9 GPIO22 I/O SFLASH, SPI, I2C, UART, PWM, GPIO 10 GPIO1 I/O SDIO, SFLASH, SPI, I2C, UART, PWM, GPIO 11 GPIO3 I/O SDIO, SPI, I2C, UART, PWM, GPIO 12 GND P Power 13 VDD33 P Power 14 GPIO17 I/O SFLASH,
XT-BL L10 User Mann nual 3.. Size and Layou ut Size forr XT-BL10 can be show wn as follow ws. Fig. 3.1 Shape for XT-BL10 X Shenzhen n Xiaoteng Teechnology Co o.
XT-BL L10 User Mann nual (a)) Vertical Viiew ((b) Side View w Fig. 3.22 Size for XT-BL10 X Shenzhen n Xiaoteng Teechnology Co o.
XT-BL L10 User Mann nual Fig. F 3.3 PC CB Layout for f XT-BL10 4.. Electroonical Ch haracterristics Table 4.1 Eleectronical Characteristi C ics Parameterrs Condition M Min Classicall Maax Unite Store Tem mperature IPC/JED DEC STD-02 20 - --30 Normal 1555 ℃ - - 2600 ℃ 22.5 --/2.0 --/2.4 3.3 - 3.66 0.8//0.
XT-BL10 User Mannual RX 11n TX(11b - 11Mbps @20dBm) 39 - 310 - mA TX(11g - 54Mbps@18dBm) - 230 - mA TX(11n - MCS7@17dBm) - 215 - mA MCU(Run Freq@ 192MHz) - 22 - mA MCU(Standby Freq@<10MHz) - 2 - mA 6. RF Characteristics The data in the following Table is gotten when voltage is 3.3V in the indoor temperature environment. Table 6.
XT-BL L10 User Mann nual 7.. The Reecommen nded Solld Tempeerature Curve 图 7. 1 Temp perature Currve when so old 8.. Minimu um Userr System m This modulle can workk just at 3.3V V working vvoltage: Fig..8.1 minimu um system Note (1) the w working volttage for module is DC 3.3V; (2) the m max current from IO off this modulee is 12mA; Shenzhen n Xiaoteng Teechnology Co o.
XT-BL L10 User Mann nual (3) WiFii module is at download mode: D88 are High leevel, then module m resett to power; (4) Wi-F Fi module is i connected d to RXD oof the otherr MCU, and d TXD is cconnected to RXD of the other o MCU. 9.. The Reecommen nded PC CB Design n XT-BL10 W Wi-Fi moddule can be sold on PC CB board directly. d Fo or the high RF perform mance for the deevice, pleasee notice thee placemen nt of the m module. Theere are threee ways to uuse the module for WiFi W Module with PCB antennna.
XT-BL L10 User Mann nual Figg.9.2 Solutio on 2 Figg.9.3 Solutio on 3 10 0. Periph heral Deesign Sug ggestion Wi-Fi moodule is alreeady integrrated into hhigh-speed GPIO G and Peripheral interface, which w may be geenerated thee switch noise. If there is a high reequest for th he power co onsumptionn and EMI characteristi c ics, it is i suggestedd to connecct a serial 10 0~100 ohm m resistance,, which can suppress oovershoot when w switchiing po ower supplyy, and can sm mooth signaal.
FCC WARNING FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.
Requirement per KDB996369 D03 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.
module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval. This limited module procedure is also applicable for RF exposure evaluation when it is necessary to demonstrate compliance in a specific host. The module manufacturer must state how control of the product into which the modular transmitter will be installed will be maintained such that full compliance of the product is always ensured.
The module manufacturers shall provide a list of acceptable unique connectors. Explanation: The EUT has one PCB Antenna, the antenna can be replaced by other authorized antennas, and the gain of each replacement antenna is no more than 1.0dBi 2.8 Label and compliance information Grantees are responsible for the continued compliance of their modules to the FCC rules.
as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. Explanation: The module without unintentional-radiator digital circuity, so the module does not require an evaluation by FCC Part 15 Subpart B. The host shoule be evaluated by the FCC Subpart B.