User's Manual

1/2 Mile Wireless Driveway
& Intruder Alert
User Manual
General Information
How does it work
The wireless driveway and intruder alert includes wireless door
chime and outdoor PIR motion sensor, the wireless distance between
them can be up to 2600 feet (800m) in open air. It is great for multiple
applications, including:
Alerting you when visitors enter your driveway.
Deterring trepassers and thieves from entering your property or
building.
Alerting you to wildlife on your land.
Using in drive-thrus to signal that a customer has pulled in, and
more.
This wireless driveway alert is expandable,which allows you to pair
various transmitter to the receiver, such as door sensor, motion
detector, push button, etc. One doorbell receiver can pair with up to
50 various transmitters and each transmitter can be set to different
ringtone. One transmitter also can pair with up to 50 receivers for
different rooms.
Specifications
Detector
1) The receiver works as an alarm buzzer or door chime, it monitors
for signals coming from the Passive Infrared (PIR) motion sensor,
and activates an alert in response to that signal. It also features a
LED indicator so you can visually tell when an alert is coming, it can
be simply plugged to an AC outlet.
2) The PIR motion sensor enables you to detect movement of people
and vehicles. It will send a signal to the receiver whenever motion is
detected. The motion sensors should be deployed outdoors, where
there is a clear view of the driveway or the likely entry and exit paths
that you plan to secure.
Overview
(2) Take off the back cover and turn
on the battery switch, when you see
the PIR sensor flashes, then you can
replace the back cover and secure the
screws to wait pair.
We recommend mounting the motion sensor at least 3-4 ft
(1m) above the ground on a sturdy, no metal surface (i.e. a
wall, wooden post or tree) with the sensor detector pointed
straight out over the area you wish to cover (such as up your
driveway looking towards your house).
This will decrease or eliminate false alarms from small
animals, give you a longer area to pick up movement, and
avoid unwanted alarms from nearby lawns /roads.
Note:
Always test that your sensor is working in your desired
location before installing it. Avoid placing your sensor in a
location where sunlight will shine directly into the sensor’s
detector window. Direct sunlight may cause false alarms
and/or damage to the PIR sensor.
(1) Mark the mounting holes with a pencil.
(2) If installing on a wooden surface, you only need to use
the included screws. Drill out your pilot holes using a 3/32”
drill bit to a depth of 3/4”. This will help you prevent stripping
of the screws and hold the sensor more securely.
LED Indicator
Volume button
Backward button
Forward button
Speaker
AC Plug
Non-rechargeable
PIR Motion Sensor
(1) Remove the screws from the four
corners of the back of the motion sensor.
Getting Started
1. Power up the indoor chime receiver
Plug the receiver into the outlet, the receiver will perform better if
kept away from other electrical equipment (e.g. TV, microwave)
2. Power up the PIR motion sensor
The motion sensor runs on battery and operates wirelessly at a
maximum distance from the receiver of 2600 feet (800m).
3. Sound volume conrol
Press the volume control button on the receiver to cycle through 5
volume levels.
4. Setting ringtone for a transmitter
There are 58 melodies to choose from
(1) Press the Forward or Backward button to choose your favorite
ringtone, the receiver playing is the ringtone selected.
(2) Please follow the pairing steps below to sync the new ringtone.
The new ringtone will be set for the most recently synced transmitter.
(3) Different ringtone can be set for each transmitter.
5. Pairing a transmitter to the receiver
(3) Please select your favourite ringtone
before pairing.
(4) Hold and press the Volume Control
Button for about 5s until a “Ding-dong” is
heard and the LED indicator starts flashing.
You are now in pairing mode.
(5) Quickly activate the tramsitter within
5s to send a signal to the receiver.
When the pairing (ringtone sync) is
successful, activate the transmtter again,
the receiver will play the selected ringtone
automatically.
6. Two or more transmitters pairing:
The pairing mode is available for a transmitter only each time.
For two or more transmitters, please follow the pairing steps (1)-(5)
once again to get transmitters paired one by one.
7. Reset:
Press Music Forward Button for about 5
seconds to reset receivers to default. When
receiver sounds “Dingdong” with LED
flashing that means reset succeeds, settting
is back to default. It comes back to the 1st
music, no transmitter is paired with receiver.
Hold forward button for 5s
Remark:
(1) Pairing mode will last for 5 seconds only.
(2) Pairing mode will quit automatically after pairing is completed. If
you didn’t pair the transmitter with receiver successfully, please
repeat the pairing steps (4)-(5) .
Receiver & Transmitter Installation
Important: Prior to installation, please test the alert wireless
distance.
For Plug-in Receiver: Just plug receiver into standard outlet in
room, then it will work.
For PIR Motion Sensor: Tools you will need for installation:
- Pencil
- Phillips screwdriver
- Electric drill with 3/32” and 7/32” drill bits (recommended)
- Hammer (optional)
(3) If installing on any other surface, such as brick or
masonry, you will use the included screws and anchors. Drill
out your pilot holes using a 7/32” drill bit to a depth of 1”.
Gently tap the anchors into your pilot holes using a hammer
until the anchors are flush with the mounting surface.
(4) Screw the bracket base to the place you want to install.
(5) Screw the back cover onto the shaft of the screws.
(6) Replace the back cover and secure the screws.
(7) Twist the ball onto the fixed base of the bracket just until
tight. Do not over-tighten.
(8) Adjust the angle of your sensor so that it is looking at
your target area.
Troubleshooting
-1- -2- -3- -4- -5- -6- -7-
-8- -9- -10- -11- -12- -13- -14- -15-
Please read the user manual carefully before use and installation.
Solar PIR Motion Sensor
1. Alerts went off randomly when no one was around.
Reason: There may be random movement of animals, high density
FR, heat radiation, or strong air flow in the detection range of sensor,
Solution: Change install location.
2. Receiver sometimes doesn't ring when someone
passing by.
Reason 1: The movement of passerby may not be detected.
To avoid constant alerting and ringing if a motion trigger occurs,
there's a 15-second time interval between 2 detections. If someone
passes through the detection range quickly during the time interval,
then the movement can't be detected.
Solution 1: Please install the motion at height of 2~2.2 meters to
cover maximal detection area.
Reason 2: The movement was detected but working range between
receiver and sensor is shorter than before due to low power status of
motion sensor.
Solution 2: Please change or charge battery for motion sensor after
you noticed the low power alert.
Input of Receiver AC 110-230V, 50/60Hz
Plug Type: US / EU / UK / AU
Optional Melodies 58
Volume Level 0-110dB, 5 levels
Wireless Transmission Distance up to 800m in open air
Adjustable Detection Distance 4-6m, 6-8m, 10-12m
Detection Angle horizontal: 60°, vertical:30°
Time Interval Between 2 Detections 15s
Expandable (Yes or No) Yes
Working Frequency LoRa 433MHz±2MHz
Waterproof Level IP44
Working Temperature -20~ +50℃
AC Plug-in Receiver
Solar Panel
Detector
PIR Motion Sensor PCB Layout
Micro USB Port
(for solar PIR motion
sensor only)
Power Switch
Detection Distance Switch
Micro USB Port: to fast charge the built-in battery when the battery
is low and no sunlight for solar charge.
Power Switch: turn the motion sensor ON/OFF.
Detection Distance Switch: there are “N”, “M”, “F” three options.
N: detection distance is 4-6m
M: detection distance is 6-8m
F: detection distance is 10-12m
You can choose any of them based on your requirement when you
install the PIR motion sensor.
Battery