Linux version of face recognition terminal —— Operation Manual
Operation manual for temperature-measuring face recognition terminal Introduction Thank you for choosing our products. If you have any questions, please contact us anytime. Disclaimer We will try our best to ensure the completeness and accuracy of the manual, but there may be some deviations in the technical expression, as well as errors in the function and operation of the product. In case of any doubt or dispute, please refer to our final explanation.
Operation manual for temperature-measuring face recognition terminal Contents Chapter I About the product........................................................................3 1.1 Product overview ..........................................................................3 1.2 Functional characteristics .............................................................3 1.3 Technical parameters ....................................................................5 Chapter II Product list ......................
Operation manual for temperature-measuring face recognition terminal Chapter I About the product 1.1 Product overview The temperature-measuring face recognition terminal is a multi-functional product that collects and verifies facial information.
Operation manual for temperature-measuring face recognition terminal Early-warning of blacklist comparison The face recognition terminal supports the blacklist comparison, which allows front end swiping and back end early-warning of the blacklist personnel of pre-input system. Stranger voice prompt The face recognition terminal supports stranger voice prompt, which will generate voice prompt when strangers are recognized.
Operation manual for temperature-measuring face recognition terminal Temperature detection The face recognition terminal supports the recognition of mask wearers and temperature detection, which enables early-warning and no access for temperatures outside the normal range. 1.
Operation manual for temperature-measuring face recognition terminal Chapter II Product list Upon receipt of the face recognition terminal product, please open the box and check the accessories for completeness.
Operation manual for temperature-measuring face recognition terminal Chapter III Use of product 3.1 Basic use The face recognition terminal can be used normally after connecting to power supply and network. The specific method is as follows: Face - ID comparison After accessing the ID reader, the ID icon will be displayed at the right bottom of the main face recognition interface. The ID can be directly placed in the card reading area, and the face - ID comparison threshold can be modified in use.
Operation manual for temperature-measuring face recognition terminal Chapter IV Main interface description On the user’s main interface of the face recognition terminal, you can view the real-time video, the connection status of ID reader, the connection status of the client, the synchronization status of the list library, the enabled status of the active object, and the dynamic face icons, etc.
Operation manual for temperature-measuring face recognition terminal Chapter V Parameter setting All parameter configurations can be set on the setting interface of face recognition terminal: [Basic setting]: Parameters such as device name, installation location, entry / exit type, blacklist record, panoramic photo upload, display IR camera, access control password, system volume and language can be configured.
Operation manual for temperature-measuring face recognition terminal [Access control setting]: Parameters such as access delay, door sensor delay, door sensor type, relay output status, tamper alarm and Wiegand type can be configured. [Fill-in light setting]: Parameters such as infrared lamp brightness, white lamp brightness and control mode can be configured. [Name list]: Operations such as query, addition and deletion can be carried out.
Operation manual for temperature-measuring face recognition terminal [Device name]: Refer to the name of the device, within 14 characters in length. Comment: The device name shall not be modified frequently. All historical data saved in the subsequent use of the device is identified with the device name. The device name must be modified before use because it cannot be modified during use.
Operation manual for temperature-measuring face recognition terminal [Entry / exit type]: Configure the entry / exit type of the product, all historical data saved after the modification will be identified with entry / exit type for the convenience of query and management of the record. Exit: Indicate that the device is installed inside the door for exit control. Entry: Indicate that the device is installed outside the door for entry control.
Operation manual for temperature-measuring face recognition terminal [Face recognition]: "Disable" and "Enable" can be selected. Face recognition is enabled by default. [ID recognition]: "Disabled", "Face - ID recognition" and "Face - ID library recognition" can be selected. ID recognition is disabled by default. [List threshold]: The default threshold is 80 and the setting range is 70-99. [Face - ID comparison threshold]: The default threshold is 60 and the setting range is 30-100.
Operation manual for temperature-measuring face recognition terminal [Active object threshold]: The default threshold is 5 and the setting range is 0-10. [Individual recognition interval]: 1 second by default and the setting range is 0-255. [Recognition distance]: Unlimited by default, support "0.5 m", "1 m" and "2 m" recognition distance selection. [Stranger recognition]: Disabled by default, support "Turn off", "Voice prompt" and "Voice prompt and face capturing" section.
Operation manual for temperature-measuring face recognition terminal [Enable temperature detection]: After turning on the switch, the temperature is detected during the face recognition. Temperature measurement distance is 0.4 m. [Temperature detection range]: The system provides default values that can be changed.
Operation manual for temperature-measuring face recognition terminal [Early-warning of temperature upper limit]: After turning on the switch, there will be a beep alert when the temperature exceeds the upper limit. [No access for temperature early-warning]: After turning on the switch, access is prohibited when the temperature exceeds the upper limit.
Operation manual for temperature-measuring face recognition terminal [Advertisement slogan]: Type in texts within 14 characters in length. Display on the user’s main interface after saving. [Enable advertisement]: Turned off by default. Click to turn on or turn off. The system will display advertisement picture after turning on. [Advertisement switching time]: 5 seconds by default.
Operation manual for temperature-measuring face recognition terminal Step 2: After connecting the device, click [Select picture] button to enter the picture selection interface and select the pictures to be uploaded on the interface. Comment: The maximum number of uploads is 15; the photo ratio is 16: 9, and the resolution is 800X1280. [Cancel default]: Click the button to delete the imported advertisement pictures and return the advertisement style to factory default status.
Operation manual for temperature-measuring face recognition terminal normally closed types. [Relay output status]: Normally open by default, normally closed mode can be selected. [Tamper alarm]: Turned off by default, you can check to turn on. [Wiegand type]: Support Wiegand 26, Wiegand 34, Wiegand 66 formats. 5.6 Fill-in light setting Click [Fill-in light setting] to enter the interface. [Infrared lamp brightness]: Drag the progress bar to configure the brightness value.
Operation manual for temperature-measuring face recognition terminal Intelligent fill-in light: After clicking the button, the fill-in light will be turned on and off intelligently according to the environment. Setting can be carried out according to the actual environment. After setting, click [Save] on the upper right corner to save the modified contents. 5.6 Name list Click [Name list] to enter the interface. [Query]: Support the list query by entering ID number or name.
Operation manual for temperature-measuring face recognition terminal Click the [Avatar] interface and complete the face photo input according to the prompts. [Whitelist]: Check the option and click the [Query] button to query all whitelist information. [Blacklist]: Check the option and click the [Query] button to query all blacklist information. Click [Previous page] and [Next page] buttons to query the list data by turning the page.
Operation manual for temperature-measuring face recognition terminal 5.8 Historical record Click [Historical record] to enter the interface. [Query]: Support the list query by entering ID number or name. Click [Previous page] and [Next page] buttons to query the historical record by turning the page. [Recycle bin]: Click the icon to delete the selected data or all data according to the prompts.
Operation manual for temperature-measuring face recognition terminal 5.9 Network setting Click [Network setting] to enter the interface. [Static address]: Enabled by default, and IP address, gateway, subnet mask, DNS server 1 and 2 parameters can be set.
Operation manual for temperature-measuring face recognition terminal [Dynamic address]: Support DNS server to automatically assign addresses. 5.10 Image setting Click [Image setting] to enter the interface.
Operation manual for temperature-measuring face recognition terminal [Video output setting]: Support manual settings of brightness, contrast, tone and saturation. 5.11 System maintenance Click [System maintenance] to enter the interface.
Operation manual for temperature-measuring face recognition terminal [System time]: The device time can be set. click [Setting] button to confirm after adjusting the time, and click [Refresh] button to update the time. [Data backup and recovery]: Click [Data backup] and [Data recovery] buttons to carry out data backup and data recovery. [Log copy]: Support to copy log information by USB. [Device restart]: Click the button to restart the device manually.
Operation manual for temperature-measuring face recognition terminal [Software upgrade]: Click the button and upgrade the system software according to the prompts. Comment: Options such as data operations require inserting a USB. 5.12 About the system Click [About the system] to enter the interface. The interface provides the current system status information.
FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.