1、Power button( ).Long press the button for 2 secs to turn on/off. Short press to lock the button, and then short press to unlock. 2、Channel switch/pairing button( ), long press for 3 seconds to enter the pairing state, short press to select a different dog terminal.
shock. 6、Flashlight button( ), cycle short press to switch between long on/flash. (standalone system, still available after shutdown) 7、Beep button, short press ( )(▲)( )( )( ) ,it will emit 5 different sounds. When the key is locked, press and hold the ( ) for 3 seconds to make a music sound.
Quick User Manual 1.Charging 1.1 Use the included USB cable to fully charge the collar and remote control at 5V. 1.2 When the remote control is fully charged, the battery display is full. 1.3 When the collar is fully charged, the red light turns green. It fully charges in about two hours. 1.4 The battery level is shown on the remote control screen. 2.Collar On/Off 2.
will beep and vibrate to turn on. 2.2 After it powers on, the green light flashes once for 2 secs, automatically enter the sleep state if it is not used for 6 minutes, and the green light flashes once for 6 secs. 2.3 Press and hold for 2 seconds to power off. 3.Remote control On/Off 3.1 Long press the button ( ) for 2 seconds to turn on/off. There will be a beep and the screen will light up. 3.2 Long press the button( ) for 2 seconds, a beep will be heared and the display will turn off. 4.
4.1 Short press to lock the button( ), and then short press to unlock. 4.2 Recommended to lock the buttons when not in use to prevent misuse. 5.Pairing(One‐to‐one has been paired in the factory, you can use it directly) 5.1 Make sure the collar is turned off. Press and hold the power button( )for 3 seconds, until 4 beeps are heared, the indicator light flashes alternately, then it is ready to pair. 5.
5.4 The icon on the remote will stop flashing after pairing is complete.The battery level of the collar is displayed on the remote control screen. 6.Cancel pairing 6.1 Long press the remote control channel switch button( ) for 3 seconds, then the icon will flash, and Select the collar you want to cancel. 6.2 Short press the ( ) key, then press the ( ▲ ) button to cancel the pairing. 7.
Repeat the above operations, you can continue to pair other collars. 7.1 One channel has one collar, and multiple collars cannot be connected to the same channel. 7.2 After all four channels are paired, you can press the channel switch button( )to select 1 to 4 channels to control a single collars, or control all collars at the same time. 7.3 Vibration and shock levels can be individually adjusted when controlling a single collar. 7.4 4.
.Vibration intensity adjustment 9.1 Short press the Level setting button( )and the vibration icon will flash. 9.2 Press the up and down keys to adjust the level (0‐9). 9.3 Press ( ) to save. 0 is to stop the vibration, 9 is the strongest vibration. 10.Vibration command 10.1 Short press the vibration button( )and the collar will vibrate once. 10.2 Long press the vibration button( ),the collar will vibrate continuously and will stop after 8 seconds.
.3 When controlling multiple collars at the same time, the vibration level is the current set value. 11.Shock intensity adjustment 11.1 Short press the Level setting button( ), the shock icon will flash. 11.2 Press the up and down button to adjust the value (0‐30). 11.3 Press( )to save. 0 is to stop, 30 is the strongest level. 11.4 Recommended to start training the dog from level 1, observe its response, and then slowly increase it. 12.
12.1 Short press the electric shock button( )and there will be an electric shock for one second. 12.2 Long press the electric shock button( )and the electric shock will stop after 8 seconds. 12.3 Release the shock button and press the shock button again to activate the shock. 13.Electronic fence function (Model X3 Only) 13.1 Long press the function selection button( )for 3 seconds and the electronic fence icon will pop up. 13.2 A double circle is displayed, indicating that the fence distance is 150 meters.
14.Turn on the flashlight 14.1 Regardless of power on/off, short press the flashlight button( )and the light will turn on. 14.2 Short press again and the flashlight will switch between 3 modes: long on/on/off. 15.Song playing After the collar and the remote control are paired normally, in the locked state, long press the beep button( and the collar will play music for 10 seconds.
16.Shock intensity test 16.1 Screw the contact points onto the collar. 16.2 Tighten the contact points with neon bulb, and then put on the conductive cap. Also the contact point of neon bulb is aligned with the Contact points. 16.3 Level 1: Neon faint, Level 30: Highlight. Training Tips 1.Choose a suitable contact points and Silicone cap, and put it on the dog's neck. 2.
3.Be sure to leave one finger between the collar and the dog's neck.Dog zippers must not be attached to collars. 4.Shock training is not recommended for dogs under 6 months of age, aged, in poor health, pregnant, aggressive, or aggressive towards humans. 5.In order to make your pet less shocked by electric shock, it is recommended to use sound training first, then vibration, and finally use electric shock training. Then you can train your pet step by step. 6.
Trouble shooting 1.When pressing buttons such as vibration or electric shock, and there is no response, you should first check: 1.1 Check if the remote control and collar are turned on. 1.2 Check whether the battery power of the remote control and collar is sufficient. 1.3 Check if the charger is 5V, or try another charging cable. 1.4 If the battery has not been used for a long time and the battery voltage is lower than the charging start voltage, it should be charged for a different period of time. 1.
matched first. 3.2 If it cannot be paired, the collar and remote control should be fully charged first. The collar must be in the off state, and then long press the power button for 3 seconds to enter the red and green light flashing state before pairing (valid time is 30 seconds). 3.3 Check whether the remote control buttons are pressed. 3.4 Check whether there is a strong signal, electromagnetic field interference, etc.
4.Avoid dropping the device on a hard surface or applying excessive pressure to it. 5.Do not use it in a corrosive environment, so as not to cause discoloration, deformation and other damage to the appearance of the product. 6.When not using this product, wipe the surface of the product clean, turn off the power, put it in the box, and put it in a cool and dry place. 7.The collar cannot be immersed in water for a long time. 8.
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna.
Specification Model X1/X2/X3 Packing size 6.7*4.49*1.73 inches Package weight 0.63 Pounds Remote control weight 0.15 Pounds Collar weight 0.18 Pounds Adjustable range of collar Diameter 3.
1、Remote control 1PCS 2、Collar unit 1PCS 3、Collar strap 1PCS 4、USB cable 1PCS 5、Contact Points 2PCS 6、Silicone cap 2PCS 7、Neon bubble 1PCS 8、Lanyard 1PCS 9、User Manual 1PCS Customer Services Email:mimofpet@outlook.