User's Manual

www.rockspace.hk
10/100/1000Mbps
LAN ports
10/100/1000Mbps
WAN/LAN port
DC power jack
Reset
button
Power DC-IN
Mesh
Done .
2. Use the other power adapters to connect the remaining
secondary nodes to separate power sources, and their LED
light solid green. Wait for about 40 seconds. The secondary
node is connecting to another node when its LED indicator
blinks green.
3. After the primary node has been congured, the app will explain
how to set up the other nodes. Tap "OK" to view the specic steps.
You can also select "Add rock space mesh" on the setting page and
follow the steps to nish settings.
4. Observe the LED indicators of the secondary nodes until their
LED indicators light one of the following colors:
5. If the LED Indicator of a node does not light solid green, relocate
it according to the location recommendations in V. part to get better
connection.
Solid green Good connection
Solid yellow Fair connec tion
Solid red Disconnected
To access the internet with:
− Wired devices: Connect wired devices to the LAN ports of
any node.
− Wireless devices: Connect wireless devices to the WiFi
network using the SSID and the WiFi password you set.
If you want to manage the network anytime, anywhere, tap
and use your account to login.
FAQ
A1: Run the RS WiFi App, tap Settings in the lower-right corner, tap Wireless
Settings, change your SSID and password, and tap Save.
Then, you need to reconnect your mobile devices using the new SSID and
password.
A2: Tap the node on the RS WiFi App, tap “…” in the upper-right corner, and
choose “Delete”.
Note: Removing operation restores the node to factory settings.
A4: With the nodes powered on, hold the Reset button of your primary node down
using a paper clip for about 6 seconds, release when the LED indicator blinks
fast. Your network is reset successfully when the LED indicator lights solid on
then blinks again. And all nodes are restored to factory settings
A3:
Yes. Run the RS WiFi App, tap Settings in the lower-right corner, tap Add
Nova, and follow the on-screen instructions to add.
Q1: How can I change my SSID and password?
A6 : Step 1: Run the RS WiFi app. Go to Settings>Internet Settings> Connection Type.
Select "Bridge" and tap "Save" on the upper right corner.The app will reconnect the
network and please connect again when the button "Connect" comes out. The
network will automatically match the mesh SSID and nish Internet connection.
Step 2: Then power on the other two nodes, startup completes when LED blinks green.
Mesh network is established when LED turns to solid green.
Step 2: Try to close the Fast Roaming function as the temporary solution, checking
whether it is something related to this function;
Step 3: Please reach out via 【Tech Support Email: [e-mail]】 and
provide your printer information(Brand and product number) to the tech team for
further help, if you still fail to connect.
Q6 : How to set AP mode?
A8 : You can use the "Smart Assistant" in the Setting page. Enable the button and the mesh
system will switch to 2.4G band in the following 30 minutes in order to connect all
your 2.4G devices. Meanwhile, other devices will connect to this band too. After half
an hour, the connection would interrupt and switch back to 5G band, while 2.4G
devices connected to 2.4G band and 5G devices to 5G band. If you need further
help with it, please reach out via 【Tech Support Email: [e-mail]】
for more support.
Q8 : How can I connect my 2.4G devices to the Internet?
A7 : Step 1: Please conrm whether the RS WiFi app you're using is the latest version
V1.0.0.32, which is the one has xed the problem of printer connection.
Q7 : How can I connect the mesh network to my printer?
Q2: How can I remove node from my WiFi network?
Q4: How to restore my network to factory settings?
Q3: Can I add another new set of node to expand my network coverage?
A5:
If your 2.4 GHz WiFi-enabled device supports the WPS function, perform the
steps below:
Step 1 Run RS WiFi App, tap Settings, WPS, and the WPS button
corresponding to the node near your device.
Step 2 Within 2 minutes, enable the WPS function on your device.
If your 2.4 GHz WiFi-enabled device does NOT support WPS function, perform
the steps below:
Step 1 Connect your smart phone used for setup to the WiFi network.
Step 2 Run RS WiFi App, tap Settings, Smart Assistant, and Enable. Your
smart phone connects to the 2.4 GHz WiFi network.
Step 3 Use the smart phone to set up your 2.4 GHz WiFi-enabled device
guided by its App.
Q5: My 2.4 GHz WiFi-enabled devices, such as a home security camera, cannot
connect to my nova WiFi network. What should I do?
Connect the primary node
1. Power o your modem, and remove its battery (if any).
2. Use the included Ethernet cable to connect a LAN port
of your modem or the Ethernet jack to the (WAN/LAN)
port of any node. This node is your primary node.
4. Use the included power adapter to connect the primary
node to a power source. Its LED indicator lights solid
green. Wait about for 40 seconds. The system
completes startup when the LED indicator blinks green.
3. Reinstall the battery of your modem, and power it on.
* The rst node you set up functions as the primary node,
while the rest are referred to as the secondary nodes.
Ⅱ
Set up the primary node for
internet access
1. Go to the WiFi network list on your mobile device;
select the SSID of the primary node, and enter its
password. The default SSID and password are
specied on the bottom label of any node.
Ⅲ
2. The app will automatically turn back to the WiFi network list and
nd out the SSID Name labeled on the bottom of the mesh node,
input the given default password and connect to the network.
3. After the mesh node will nally connect to the network, open
the RS WiFi app again. If the page showing up is the scaning one,
click the name of the network on the upper left side of the page
and return to the rst page of the app. You do not need to scan for
a second time.
4.
Follow the given instructions. The setup wizard appears. Tap "Setup".
5. The app automatically detects your internet connection type.
Enter information according to the internet connection type and
tap "Next". The mesh unit is connected to the Internet and the app
proceeds to the next step.If your Internet connection type is PPPoE.
Enter your PPPoE user name and password and tap "Next”.
If your internet connection type is dynamic IP, tap "Next".
If your internet connection type is static IP, enter your IP address and
other information your ISP provides, and tap "Next".
6. When the mesh unit and the app is connected successfully,
it says" Connected".
7. The instruction will guide you to the Wireless Setting page for
further customizing your personal WiFi Name and Password of the
mesh. Tap "OK" when you nish setting up the new one.
Note: If you change the wireless network nameand password and
tap "OK", your mobile phone will disconnect with the mesh Wi-Fi
network. You need to reconnect to the new wireless network you
congured.
8. When the indicator of the mesh unit turns solid green,
it is connected to the Internet.
Download and install the
RS WiFi App
Ⅰ
Mesh x 3 Ethernet cable x 1
Power adapter x 3 Quick installation guide x 1
Get to know your device
Package contents
Ⅳ
Setup the primary node on
RS WiFi APP
Model: RSD0613
Power: 12V 1.5A
FCC ID: V7TMESH12
IC: 9034A-MESH12
MAC:
SN:
AC2100 Tri-band Whole Home Mesh WiFi System
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Power DC-INWAN/LAN
LAN1
LAN2
Made in China
Modem
Ethernet jack
Or
User Manual
Please read this instructions closely and keep it properly.
Whole Home Mesh WiFi System
RSD0613(3-pack)
RS WiFi
RS WiFi
RS WiFi
2. Run the RS WiFi App and follow the onscreen
instructions to set up the primary node. After the
primary node is connected to the internet, its LED
indicator lights solid green.
1. Place each node:
−
In an elevated, open position within the coverage area
of your existing RS WiFi network.
−
Keep your nodes away from electronics with strong
interference, such as microwave oven, induction cooker,
and refrigerator.
V
Connect the secondary nodes
to the Internet on RS APP
For EU/EFTA, this product can be used in the following countries:
BE BG CZ DK DE EE IE
EL ES FR H R IT C Y LV
LT LU HU MT NL AT P L
PT RO SI SK FI SE U K
LED indicator description
After a node is powered on, the LED indicator lights solid green for about 40
seconds to complete startup. Then, the LED indicator lights one of thefollowing
colors:
When a node is performing WPS negotiation, the LED indicator description is
shown as below:
Blinking green slowly: Ready for WPS negotiation.
Blinking green fast: Performing WPS negotiation with a wireless device.
The primary
node
The secondary
node
Blinking green fast
Solid red
Solid green
Solid yellow
Solid green
Blinking green slowly
Blinking green fast
Solid red
Connecting to the internet
Connecting to the internet
Connected to the internet
Disconnected
Good connection
Fair connection
Disconnected
Wait for connecting to another node,
or searching for another node
Node Type Status Description
*NOTE: Please go to the rock space official website to download
www.rockspace.hk/en/news.aspx
specific using instructions.
Shenzhen Renqing Excellent Technology Co., Ltd.
Address: 104, No.15, Longfu Industrial Zone, Huarong Road, Tongsheng
Community, Dalang Street, Longhua District, Shenzhen, China
Email: [e-mail]
Website: www.rockspace.cc
Technical Phone Support: [phone]
Service Time: EST: 9:00-17:00 / PDT: 06:00-14:00,from Monday to Friday
1.Run the RS WiFi app, click "Add device". The QR code
scanning page would show up here. Select "Add Manually"
on the left side below the scanning zone.