Installation Instructions

ManualsBrandsShenzhen qiuyu Electronic ManualsComputers & AccessoriesTablet pc

Connect Family

RE667 SlimlineTouchpad

The RE667 Slimline Touchpad

is an intuitive interface

for controlling the security system. It is AC powered and

communicates with the panel wirelessly.

Features

•

Vibrant 7’’ Android™ tablet display

•

Provides local control of security and automation functionality

•

Wall or table mounted

•

Encrypted, Connect+ and BAT-Connect enabled, battery-backed

Wi-Fi™ connection

Installation Overview for Connect+

Confirm the panel has a Wi-Fi DeviceLink card installed.

Choose a mounting location. Touchpad can be mounted on a wall or tabletop.

Identify your network and verify signal strength before mounting it permanently.

Installing the Wi-Fi DeviceLink Card

•

Disconnect the panel’s AC power and backup

battery.

•

Install the Wi-Fi DeviceLink card in Slot 2 by

carefully aligning the nylon retention posts and

the 8-pin connector while pushing the card

firmly until all posts are fully seated.

•

Reconnect the panel’s AC power and backup

battery.

•

Verify the Wi-Fi card LEDs are on.

Power

Input

Slot

Backup

Battery

Ensure the panel is powered.

Power the Touchpad by applying AC power.

Select the “Connect” option to see the available networks. If the “Connect” option is

not available, press “Setup” then “Factory Default”. The Touchpad can be connected

to either the Wi-Fi DeviceLink card or the home router for internet access. (Internet

access allows for camera control, weather updates, and the ability to modify users.)

Once a network is determined, verify the signal strength. If the signal strength

displayed is less than 35, relocate the Touchpad or Connect+ panel. If neither options

are available, install an RE621 Touchpad Range Extender.

Note:

If connecting to a home network router, the Connect+ needs to be connected

to the same network via ethernet. The Touchpad cannot connect to the panel over an

unsecured oropen network.

Summary of content (13 pages)

PAGE 1
RE667 SlimlineTouchpad I Connect Family The RE667 Slimline Touchpad is an intuitive interface for controlling the security system. It is AC powered and communicates with the panel wirelessly. Features • • • • Vibrant 7’’ Android™ tablet display Provides local control of security and automation functionality Wall or table mounted Encrypted, Connect+ and BAT-Connect enabled, battery-backed Wi-Fi™ connection Installation Overview for Connect+ 1. Confirm the panel has a Wi-Fi DeviceLink card installed.
PAGE 2
72DF 9EF8 By default the Touchpad network list will show Connect+ and BAT-Connect access points. To view all networks in range tap the “Show all networks” button at the bottom of the network list. 4. Mount the Touchpad. Refer to section “Touchpad Mounting Options” for mounting instructions. 5. Enroll the Touchpad by pressing the enroll button on the side of the panel until it beeps once and then select the desired network. Note: If connecting to a home network, enter router credentials at the Touchpad.
PAGE 3
Installation Overview for BAT-Connect 1. Chose a mounting location. Touchpad can be mounted on a wall or tabletop. 2. Identify your network and verify signal strength before mounting it permanently. 1. Ensure the system is powered. 2. Power the Touchpad by applying AC power. Note: The Touchpad cannot run off panel bus. Existing wiring needs to be moved to the provided power adapter. For additional details, please refer to Wall Mounting section. 3. Select the “Connect” option to see the available networks.
PAGE 4
5. If using camera or user management features, internet access is required. In order to access the internet your BAT-Connect must be connected via ethernet or Wi-Fi. In addition you must log in to the Alula platform using the account owner username and password. To log in go to Settings and select Touchpad. Enter master code, then select Alula Cloud. 6. Test the Touchpad by arming and disarming the system from the Touchpad. Touchpad Mounting Options Table Top Mounting 1.
PAGE 5
Wall Mounting 1. There are two mounting configurations. A. If mounting on a stud, use the two centered holes labeled below [A]. B. If not mounting on a stud, use the four corner mounting holes. Insert the wall anchors prior to screwing the screws in place [B]. A B B 2. There are two methods for connecting power to the Touchpad. A.
PAGE 6
3. Slide the Touchpad onto the mounting plate. Push any extra wire into wall before sliding onto mounting plate. 4. Drop cover behind Touchpad. 5. Lock in cover by pressing at these locations until snapped into place. 6. Plug in powersupply.
PAGE 7
Devices (continued) • Open and close Z-Wave garage door openers • Control Z-Wave thermostats **PLEASE SEE Z-WAVE USER GUIDE FOR ADDITIONAL INFORMATION** Cameras • Cameras can be viewed directly from the Touchpad. Live view, clips, and event notifications are supported. Doorbell live view will automatically be displayed when the doorbell button is pressed. Internet access isrequired.
PAGE 8
More - Settings • Display • Brightness - adjust slide bar to change brightness level • Auto sleep display - when enabled the Touchpad screen will go to sleep after programmed period of inactivity. When auto sleep is disabled, the Touchpad will show wallpapers with time and arming level. Show Wallpaper shows/hides wallpaper images. If disabled the background is black.
PAGE 9
• Panel (must enter code to access) • Global Chime - enables or disables panel sensor chime mode • Quick Arm - arm the panel without entering your access code. Access code is still required to disarm. • Manage Access - manage device users directly from the touchpad (only the account owner can modify users, internet access isrequired) • Edit Installer User - configure the system’s installer access code and password.
PAGE 10
Home Screen Functions* The headline indicates panel status such as “Disarmed” or “Armed Stay” The time zone can be configured on Alula Connect Tap to mute beeps during arm/disarm action Tap to turn the Touchpad’s display off Tap to edit favorite zones, device, scenes, and cameras Tap to disable entry delay Tap to view Panic options Tap one of the arming buttons to arm the panel Panic Functions* Hold for three seconds to trigger police, fire, OR auxiliary alarm Turn on/off individual panics *These
PAGE 11
Pro Tips When a Touchpad is connected to the BAT-Connect or Connect+ through the DeviceLink interface it remains available for use during momentary power outages. The BAT-Connect, Connect+, and the DeviceLink connection are battery backed. If the Touchpad is connected only via the premise Wi-Fi, Alula recommends that all network equipment including the Wi-Fi access point be connected to a suitable UPS to ensure system availability during power outage.
PAGE 12
Specifications Physical Specifications Wall Dimensions Table Top Footprint Weight 4.27in[10.84cm] x 7.42in[18.85cm] x 1.60[4.06cm] Deep 4.58in[11.64cm] x 7.42in[18.85cm] x 6.63[16.84cm] High 1.29lbs[585g] Pilot Hole for Screw into Wood Pilot Hole for Wall Anchor Ø 1/8in [3mm] Ø 3/16in [4.
PAGE 13
assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: Communicator has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the phone kept 0mm from the body.