GWF-5M02 PRODUCT SPECIFICATION MODEL: GWF-5M02 VERSION: V1.
Historical Releases Version Modified Content Writer Auditing date Department V1.0 the first version Jasmine Ning Qing 2017-06-13 Product dept.
Catalogue 1.Product Basic Information 4 1.1 Product Introduction 4 1.2 Product Features 5 2 Product Basic Function 5 2.1 Brief Specification 5 2.2 Hardware Information 5 2.3 Software Information 9 2.4 Mechanical Information 9 2.4.1 Product Appearance 9 2.4.2 Product Dimension 9 2.4.3 RF output Connection Information 10 3. Approval and Certification 12 4.Environment Requirements 12 4.1 Suitable Temperature 12 4.2 Suitable Humidity 12 5.
1. Product Basic Information 1.1 Product Introduction The 5M02 is a low cost and multi-use WLAN module, it adopts the latest 802.11ac technology and fully complies with 802.11a/b/g/n/ac standards. The 5M02 module designed is to focusing on wireless connection, equipped with 4/6 pin connectors, it supports USB1.0/USB2.0 interface. The module uses high-integration MAC/BBP chip and RF single chip RTL8811AU. These features deliver reliable performance, extensive application and operational excellence.
1.2 Product Features Built in on-board antenna, or connect to external antenna via IPEX. WPS supports. 802.11b: 1, 2, 5.5, 11Mbps 802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11n: (20MHz) MCS0-7, PHY rate reaches to 72Mbps; (40MHz) MCS0-7, PHY rate reaches to 72Mbps 802.11ac: PHY rate reaches to 433Mbps(80MHz) Support multiple encryption mode: WFA, WPA, WPA2, Personal, WPS2.0, WAPI. Equipped with 4/6 pin connector, support USB2.0/1.
Encryption mode WFA, WPA, WPA2, Personal, WPS2.0, WAPI. 802.11b: 17±1 dBm@11Mbps Typical Transmit Power (feed point to antenna) 802.11g: 15±1 dBm@54Mbps 802.11n: 15±1 dBm@150Mbps 802.11ac: 11±1 dBm@433Mbps(AC80) 802.11b: -80+/-1dBm Receive Sensitivity 802.11g: -73+/-1dBm 802.11n: -70+/-1dBm(HT20); -64+/-1dBm(HT40) 802.
2.2 Hardware Information 1. Block diagram 5G/TX CONNECTOR J1 or J2 5G/RX EXTERNAL 5G/TX/RX FEM ANTENNA DEX RTL8811AU DUPLEXOR COAXIAL CONNECTOR BUILT-IN AERIAL ANTENNA 2.4G/TX/RX 2. 4/6 pin connector interface schematic diagram 3. 4/6 pin connector interface definition and function description as below: Pin NO. 4-pin 2.0mm pitch Description Remark J-1 TX TX enable Not available temporarily J-2 DVDD-5V0 USB power DC 5V+/-0.
J2-1 DVDD-5V0 USB power J2-2 UDM Data- J2-3 UDP Data+ J2-4 GND GND DC 5V+/-0.5V When you consider pull-up resistor (pull-down resistor), you need to think about resistor value. J1-1(TX) connects to GND by pressing SW1 button, it is at 3.3V low level active, now it doesn’t support the function temporarily. SW1 2 1 TX J1-6(WPS) connect to 3.3V by pressing WPS button(SW2), it is high level active, the schematic diagram as below.
2.3 Software Information The table below is for users to check the available Operation System and its version: OS Available OS Version YES XP YES Win7 YES Win8 YES Vista YES Win10 Linux YES Linux2.6 or above Android YES Android2.6 or above Mac YES 10.3-10.10 Windows 2.4 Mechanical Information 2.4.1 Product Appearance The view of top and bottom layer of GWF-5M02 can be displayed in the following pictures 2.4.
Three location holes position map as below (dimension unit: mm): 2.4.3 RF Signal Input and Output A. Using external antenna to process signal input and output.
an I-PEX MHF receptacle (RF connector). The profile of I-PEX connector is contained in the following picture. Note: I-PEX interface can be welded to the suitable position in PCBA When we use external antenna via I-PEX interface, on-board antenna will interrupt signal connection. B. Using on-board antenna to process signal input and output.
3. Approval and Certification Certification Approval FCC Pre-scan undergoing CE Pre-scan undergoing ROHS Pre-scan undergoing 4. Environment Requirements 4.1 Suitable Temperature Working Temperature: -10℃~+50℃ Storage Temperature: -20℃ ~+85℃ 4.2 Suitable Humidity Working Humidity: 20%~85% Storage Humidity: 20%～95% Notice: To keep the normal service life and ensure the excellent working performance of our device, please use it and store it abide by environment requirements strictly.
6. Disclaimer This SPECIFICATION document is the guidance of the installation and tentative usage of our products. Before operating the product, please read this data sheet carefully. All rights reserved. Any reproduction, translation or simplification of this data sheet in whole or in part is strictly prohibited without written permission from our company. We do not provide any guarantee about this data sheet, software or other relevant information.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
