Instruction Manual Motion Sensor(PIR) Model Name: NAS-PD02Z Thank you for your support Please read the instruction manual carefully before operating Please keep the instruction manual after reading Shenzhen Neo Electronics Co.
Product Introduction PIR is a passive infrared detector or physical sensor, the sensor doesn’t emit any energy but only passively receive and detect infrared radiation from outside. Under room temperature, all items have radiation. Human beings are warm-blooded animal with stable infrared radiation, are most easily to be detected. That’s why we also call it body sensor. PIR send messages via Z-wave network to the Z-Wave main controller.
Product Configuration Inductive area Code button Battery LED light Holder Sticker Screw Screw stopper Product List PIR Holder Battery Screw Screw stopper Sticker Instruction manual 1pc 1pc 1pc 2pcs 2pcs 1pc 1pc
Including Sensor (PIR) to Z-Wave Network The PIR can be included to the Z-wave network by pressing on the code button. 1) Disassemble the PIR main body and insert the battery into the contact sensor. Make sure the device is located within the direct range of the controller. 2) Set the controller into the learning mode (see mail controller’s operating manual). 3) Quickly, triple click the code button, LED light will flash red for 5 times. 4) PIT will be detected and included in the Z-Wave network.
Battery Installation Open the PIR Install the battery Close the PIR Fix PIR on the Holder Detection range and Working conditions PIR has to be installed in a corner of the room or perpendicularly to the doors. Actual detection range of the sensor can be influenced by environment conditions. Should false alarms be reported, check for any moving objects within the sensor’s detection area, such as trees blowing in the wind, cars passing by, windmills.
Detection range of PIR shown in the following picture Working condition If there is someone moving within the detection area, alarm triggered, and LED lights flash in the inductive area at the same time.
Tips Make sure the PIR is in the Gateway’s network. PIR is recommended to be fixed at the height of 2.0-2.2 meters off the ground. When install PIR, please keep it far away from the place where the air temperature changed sensitively, e.g., the neighborhood of air conditioners, refrigerators, stoves and so on. Furniture, large bonsai or other spacers shouldn’t be placed within the PIR’s detection area.
Main controller does not take part in such communication. Using this mechanism, PIR may communicate with other devices even when the main controller is damaged. The status of LED 1. 2. when the PIR is triggered, LED light flashes red for 2 times. When the PIR installs battery, LED light will times. 3. 4. Quickly, triple click the code button ,add the PIR to the Z-WAVE network or delete PIR from Z-WAVE network , LED light flashes red for 5 times.
Restore the Sensor (PIR Motion detector) to Factory Default Settings Reset procedure will delete all information on the Z-Wave network and Z-Wave controller or Z-Wave Gateway, and restore the sensor to factory default settings. 1. Remove the device cover 2. Make sure the sensor is connected to power source. 3. Press the reset button for 10 seconds, LED will flash. 4. Release the button. NOTE When the PIR is being restored factory settings, please make sure power source is connected.
Default Setting: 2. 2. On/Off Duration This parameter can be determined how long the associated devices should stay ON status. For instance, this parameter is set to 30(second), the PIR detector will send a BASIC SET Command to an associated device with value basic set level if PIR detector is triggered and the associated device will be turned on 30(second) before it is turned off. This Parameter value must be large than Parameter 6#.
activated. If the ambient illumination level falls below this value and a person moves across or within the detected area , PIR detector will send a Z-Wave ON command(i.e. BASIC_SET value = parameter 3#) to an associated device and activate it. Function: Lux Level Set Parameter Number: 5 Parameter Size: 2 Byte Available Settings: 0 - 1000(Lux) Default Setting: 100(Lux) 6.
This Sensor(Motion Detector) supports Command Classes as Below: * COMMAND_CLASS_ZWAVEPLUS_INFO (V2) * COMMAND_CLASS_VERSION (V2) * COMMAND_CLASS_MANUFACTURER_SPECIFIC (V2) * COMMAND_CLASS_DEVICE_RESET_LOCALLY (V1) * COMMAND_CLASS_POWERLEVEL (V1) * COMMAND_CLASS_BATTERY (V1) * COMMAND_CLASS_ASSOCIATION (V2) * COMMAND_CLASS_ASSOCIATION_GRP_INFO (V1) * COMMAND_CLASS_WAKE_UP (V2) * COMMAND_CLASS_NOTIFICATION (V4) * COMMAND_CLASS_SENSOR_BINARY (V2) * COMMAND_CLASS_CONFIGURATION (V1) * COMMAND_CLASS_SENSOR_MULTIL
Guarantee 1. The Guarantee is provided by Shenzhen NEO Electronics Co., Ltd (hereinafter “Manufacture” ) 2. The Manufacturer is responsible for equipment malfunction resulting from physical defects (manufacturing or material) of the device for 12 months from the date of its purchasing. 3. During the Guarantee period, the Manufacturer shall remove any defects, free of charge, by repairing or replacing. 4. In special cases, when the device cannot be replaced with the device of the same type (e.g.
