Instruction Manual

UV Sterilization Desk
Clock with Wireless
Charging
Instruction Manual: MSL-M6025Q
1 x UV Sterilizer w/Wireless Clock
1 x USB-A to Type-C Cable
1 x Instruction Manual
Type-C Input: DC 5V/3A
USB-A Output: DC 5V/2 A
Wireless Output: 5W
To reduce the risk of injury, close
supervision is required when the product is
used near children.
Do not expose the device to moisture.
Do not use the device in excess of its
output rating. Overload outputs above the
Do not use the device if damaged or
explosion or risk of injury.
Do not disassemble the device. For
professional. incorrect reassembly may
or temperatures above 104°F may cause
explosion.
use only identical replacement parts to
ensure product safety.
Attachments on the back of your phone
can impede the effectiveness of the
wireless charger, and lead to overheating.
Please remove any attachments from the
phone before charging on this device.
Using the Desk Clock:
Be sure the clock is always connected to a
power source using the provided USB-A to
Type-C Cable.
Charging Mobile Phones and other
Electronic Devices by Cable:
Connect the charging cable to your mobile
phone/device using the appropriate
connector.
Connect the USB part of the
cable to the USB-A Output(11) of the
clock.
Remove the USB cable from your mobile
device when it is fully charged.
Wireless Charging Mobile phones and
other electronic devices:
Place your wireless charging supported
mobile device on the charging surface(13).
The charging will automatically begin.
When device is charging a wireless
charging symbol “ “ will show in the top
left hand side of the clocks display screen.
Using the UV Sterilizing Function:
Press the UV-C Light Button(1) to turn on
the UV lights.
Once turned on a light up icon “ “ will
left hand side of the clocks
display screen.
The UV lights will turn off by itself after
5mins, or press button(1) to turn off UV
lights.
There will be a tone and LED turn off
once sterilize done.
DO NOT LIFT UP THE COVER(13) ONCE THE
STERILIZING PROCESS HAS STARTED:
The UV LED will automatically shut off
when you open the lid during sterilizing
process.
1.
•
2.
•
•
•
3.
•
•
4.
•
•
•
•
**
•
•
•
5.
6.
7.
8.
9.
10.
11.
12.
What’s included:
Instructions: Clock Functions:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
This device may not cause harmful
interference, and
This device must accept any interference
received, including interference that may
cause undesired operation.
Warning:
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
(1)
(2)
*
FCC Statement:
MADE IN CHINA
WARNING-When using this product, basic
precautions should always be followed:
Read all the instructions before use.
Never store or use this product in
temperatures below 32°F(0°C) or above
115°F(45°C).
Do not overcharge your phone. The
unit may become hot under excessive
use. Remove your phone once it is fully
charged. Never charge your phone for
more than 7 hours at a time.
•
1.
2.
3.
4.
SAFETY PRECAUTIONS:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
UV-C Light Button
ON/OFF Button
Next
Menu
Previous
Time Display
Temperature Display
Sterilization Compartment
Cover/Wireless Charging Surface-(phone
needs to be right in the middle of surface)
Reset
Type-C Input Port
USB-A Output
UV-C Lights
Functions:
Once power on, the display will show the
time and temperature automatically.
Press the Menu button(4) to choose a
desired mode such as (Time/Date/A1/A2/
A3) as shown below.
Press and hold the Menu button(4) to
enter the desired mode, and to adjust the
settings use the Next(3) and Previous(5)
buttons. Press(1) to turn on clock, press
3 times to adjust brightness of digit, clock
switch off after 4th time pressing.
Time:
Setting range:
- Hour: 1-12 hour or 0-23 hour cycle
- Minute: 00--59
PM is indicated at the left side of display
when set to 12 hour cycle.
Date:
Setting range:
-Year: 2000-2099
- Month: 1-12
- Day: 1-31
Clock Displays:
Setting Clock Face Display: Press Next
button to choose from 3 clock face modes
as explained below:
• Dp-1: The time lasts for 10 seconds
and then switched to show the date for 3
seconds before switching back to the date.
• Dp-2: This mode display time or date at
• Dp-3: display time
Alarms:
Press and hold the Menu button(4) to
Select A1, A2 or A3 and to set the desired
alarm time use the Next(3) and Previous(5)
buttons to adjust the hours, then press the
Menu button(4) to toggle to minutes.
When Alarm is set, a alarm logo will display
at the bottom left side of the clock display.
When Alarm rings, press buttons 2,3,4 or
5 to turn off alarm. If not it will turn off after
60 seconds and reset for the next day.
Temperature:
Once clock is turned ON the temperature is
automatically detected and displayed.
- Default temperature units:
0˚C - 50˚C (32˚F - 122˚F).
Long Press Previous button(5) to switch to
Fahrenheit/Celsius.
The temperature will always display except
when Power-save mode (ON).
Power-saving:
Turn on/off the power-saving function by
pressing the Previous button(5). “--Sd” will
display press the button again to turn ON
power-saving. Display will show “ONSd”
when ON and “--Sd” when OFF.
External power-off protection
If power supply is interrupted, clock
function will keep time though the LED
display will turn off and buttons will be
unresponsive. Once powered is restored,
the time will resume appropriately.
•
•
•
1.
•
•
2.
•
3.
•
4.
•
•
•
5.
•
•
•
6.
•
•