Instruction Manual

Bamboo Fast Wireless
Charging Dock Station
Instruction Manual
MSL-M6020Q
1 x Wirelsss Charging Dock Station
1 x UL Listed AC adapter
1 x Instruction Manual
AC Adapter input: 12V/2A
USBA Output 1/2/3: Total 5V/2.4A (Max)
Wireless Output: 5W/7.5W/10W
Wireless Charging Mobile phones and
other electronic devices:
Connect the provided UL Listed AC
adapter cable to the DC input port(3) of
the charging station, then connect the AC
adapter to a power source. LED indicator
will glow GREEN when the device is in
wireless charging standby.
Place the wireless charging supported
mobile device on the wireless charging
surface(1), LED will glow RED when
device is charging.
Once fully charged remove the device.
1.
•
•
•
Note: When wireless charging, if the LED
a wireless charging device or there is an
object between the device and charging
surface interfering with the charging.
process.
**
Charging mobile phones and other
electronic devices:
Connect the charging cable to your mobile
phone/device using the appropriate
connector.
Connect the USB part of the
cable into the USB-A Output(2).
USB-A 1: 5V/1A; USB-A 2: 5V/1A ;
USB-A 3: 5V/2.4A.
Remove the cable from your mobile device
when it is fully charged.
2.
•
•
•
Smart Watch Charging Cable Stand:
Take the USB end of the watch charging
cable(NOT INCLUDED) and run it through
the front of the watch charging stand(4).
Plug the watch charging cable into the
3.
•
•
1.
2.
3.
4.
5.
6.
7.
8.
9.
•
•
•
Wireless Charging Output Surface
USB-A Outputs
DC Input Port
Watch Charging Stand
Pad/Phone Holder
Earbuds Charging Case Stand
Accessories Holder
LED Indicator
AC Adapter
What’s included:
Functions:
Instructions:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
This device may not cause harmful
interference, and
This device must accept any interference
received, including interference that may
cause undesired operation.
Warning:
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
(1)
(2)
*
FCC Statement:
MADE IN CHINA
WARNING-When using this product, basic
precautions should always be followed:
Read all the instructions before use.
Never store or use this product in
temperatures below 32°F(0°C) or above
115°F(45°C).
Do not overcharge your phone. The
unit may become hot under excessive
use. Remove your phone once it is fully
charged. Never charge your phone for
more than 7 hours at a time.
To reduce the risk of injury, close
supervision is required when the product is
used near children.
Do not expose the device to moisture.
Do not use the device in excess of its
output rating. Overload outputs above the
Do not use the device if damaged or
Do not disassemble the device. For
professional. incorrect reassembly may
or temperatures above 104°F may cause
explosion.
use only identical replacement parts to
ensure product safety.
Attachments on the back of your phone
can impede the effectiveness of the
wireless charger, and lead to overheating.
Please remove any attachments from the
phone before charging on this device,
attachments can interfer with wireless
charging and lead to over heating.
USB-A 1 Output(2) of the station.
Take the charging end of the cable and
place it in the designated cut out on the
stand, if placed correctly charging surface
stand.
Place your watch on the stand to begin
charging, remove once fully charged.
True Wireless Earbuds Charging Stand:
Plug the USB end of the charging cable
(NOT INCLUDED) to the USB-A 1
Output(2) and pull the other side of the
cable through the hole of the earbud
charging case stand(6).
Connect your earbuds charging case with
the tip to begin charging, remove once
fully charged.
•
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
•
•
4.
•
•
•
SAFETY PRECAUTIONS:
8
9
This equipment complies
with FCC radiation exposure
limits set forth for an
uncontrolled environment.
This equipment should be
installed and operated with
minimum distance 20cm
between the radiator & your
body.