Air P10 D C B A D C B A
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT DISASSEMBLE. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE. CAUTION This equipent has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of FCC rules.
CAUTION Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. RF Exposure Statement: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons.
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna.
IMPORTANT SAFETY INSTRUCTIONS PLEASE THESE INSTRUCTIONS IN A SAFE PLACE WARNING: BEFORE USING YOUR Air P10 DIGITAL WIRELESS SYSTEM, CAREFULLY READ THE OPERATING INSTRUCTIONS. 1.Observe all instructions carefully in the manual. 2.Do not to perform service operations beyond those described in the Manual. Services required when the apparatus has been damaged in any way, such as: is dropped or the enclosure is damaged 3.
7.Prolonged listening at high volume levels may cause irreparable hearing loss and/or damage. Always be sure to practice “safe listening.” PRODUCT INTRODUCTION The guitar system features digital wireless technology that delivers incredible audio quality, simple setup, and is extremely reliable for any gigging musicians. It delivers a full 20 Hz - 20K Hz frequency response, so you’ll hear your guitar tone in great detail with only 5ms of latency. This wireless system operates at 2.
SYSTEM SPECIFICATION Range Latency Frequency Response THD + Noise Dynamic Range Operating Band Operating Temperature Sample Rate >100 feet Line-0-site outdoors.* <5ms 20-20K Hz,+1dB/-3dB <0.05%(1K Hz @-10dbFS) >103dB A weighted 2.4G Hz ISM Worldwide -10 C to 50 C 24bit/48K Hz uncompressed digital transmission Auto sleep/wake up mode:The transmitter will turn to sleep mode if there is no signal input for 10 seconds.
QUICK START DIAGRAM or or 1.Transmitter plugs into the Guitar (you instruments), the receiver plugs into the effects pedal, AMP, Audio, etc. 2.Turn on the Transmitter and the receiver, the A B C D LED will indicate how much volume of the battery, each LED means about 25% of the battery volume. for example,if A B C D LED all light on,it means about 100% full volume left,and the like if only A LED lights on means about 25% of the battery volume left.
is in low volume and you have to charge. 3.Channel choosing,Air P 1 0 systems’pre-set channel is channel A,after showing battery volume the A LED will flash,it indicates making pairs,if transmitter and receiver connected successfully the channel LED will stop flashing and turn solid green. if environment interuption happens, you can click the “C” button to choose another channel. 3.
BASIC OPERATION D C B A D C B A 1.Power – Slide Switch to turn on/off TRANSMETER/RECEIVER 2.Channel Select - Align TRANSMITTER and RECEIVER channels.
Click the switch to select the channel Follow the diagram below to set up the channel , meanwhile the audio signal indicator LED will flash to indicate the channel. A B D C 3.Battery LED and Channel LED The syetem at first power on,the lighting LED number indicate the battery volume,if 3 LED light on,it means 3*25%=75% battery volume left.The A LED have 2 function,one is channel A,the other is turn to red flashing in low volume and have to be charged. 4.
Q&A Four channels The wireless guitar system has four different channels, and can use up to 4 pair of systems at the same time. When your band plays for guitar, bass, keyboard and other instruments, it can set up different channels for them to prevent signal interference. When there is only one player, the different channel function can also be used for him/her to prevent interferences from different frequency bands of routers or other WIFI devices.
to two amplifiers or connect to effect pedal and pedal tuner, you need just use multiple receivers with setting up to be the same channel. Receiver Since it is the 2.4 GHz wireless system, please avoid putting the receiver close to other signal emitting devices. It is recommended that your receiver keep a distance of more than 3 meters from the other 2.4 GHz transmitter and WIFI router.
When in charging,the A B C D LED will flash orderly, different LED flash indicate different battery volume. you can judge according to the A B C D,for example the A B LEDs are in solid green,the C LED is flashing, it indicate the A B part is charged full and now is charging C,in another words 50% battery volume is charged,when battery charged full, the A B C D LED will become solid green. Channe LED Flashing after making pairs finished The channel LED light flashing indicates there is signal interference.
or need more distance for using, you can change the antenna's angle and adjust it to be the best condition. Supportive pickup and musical instrument The wireless system can works for passive guitar and active pickup, piezoelectric acoustic guitar pickup, piezoelectric violin pickup. Transmitter is better to connect to the instrument. Please avoid connecting it to distortion effect pedal or high power output interface which may incur the timbre distortion.