User's Manual

ManualsBrandsSHENZHEN LYD TECHNOLOGY ManualsElectronicsDigital Wireless Receiver

2.4GHz Digital Wireless Receiver

Thank you for choosing our digital wireless surveillance product, which is the optimal choice to monitor those places like residences and offices.

The following are the brief introduction of main features of this product. Please read this user manual carefully before use.

I. Key Features:

*Digital Wireless Kit

100% Secure, Private Communication and Interference Free

*Work with 4 Cameras maximum

*One Channel View or Quad View

* Alarm-alert When Signal Dropout

*AV Output

VGA 30 fp/s（NTSC）/25 fp/s（PAL）

*Support DVR Connection for Recording

130m Outdoor/40m Indoor Transmission

II. Product Accessories Introduction

1. Camera (Bracket Included): 1pc (Support 4pcs Maximum)

2. Power Adapters: 2pcs (DC5V/1.5A)

3. Receiver (Receiver Stand Included) 1pc

4. AV Connection Cable: 1pc

5. User Manual: 1pc

III. Product Structure:

Summary of content (9 pages)

PAGE 1
2.4GHz Digital Wireless Receiver Thank you for choosing our digital wireless surveillance product, which is the optimal choice to monitor those places like residences and offices. The following are the brief introduction of main features of this product. Please read this user manual carefully before use. I.
PAGE 2
1 2 8 3 4 9 11 7 10 12 13 14 5 15 6 1.Antenna for Wireless Camera, to strengthen the wireless signals. 2.Rainproof Housing of Camera, to enable the camera to be used outside the house. 3.Lens: the most important part of the camera. Please keep the lens clean so as to have better image. Please use special cleaning cloth to clean the lens. 4.Night Vision LED: they help to get the image at night time. 5.Pairing Button: This button is used for code pairing with its receiver. 6.
PAGE 3
1. Take out the Camera, Receiver, Power Adapters and all the accessories from the package. (As shown below) 2. Install the antenna of the camera. (As shown below) 3. Install the bracket of the camera. There are two ways of bracket installation for your reference (A and B as shown below). A B 4. Plug in the Power Adapters for the camera and receiver, and connect the AV cable between the receiver and the monitor. Then pair the code of the camera and receiver to display the real-time image on the monitor.
PAGE 4
6. Please make sure the Camera Power Adapter is well connected and the Receiver is well connected with the Monitor. V. Operation Instruction： 1. Power On Instruction Please connected the Receiver with the Monitor, and plug in the power adapter of the receiver, then you can view the following image on the monitor. 1 2 3 4 1： Signal Bar 2. Wireless Camera Indication 3. FPS of wireless transmission 4. TV System Indication.
PAGE 5
2. TV System Switching It is used for switching the TV system of the Camera kit. Because TV systems are various from each country, you may need to set the TV system of the wireless camera kit to get a clear image. NTSC 制 PAL 制 3. Code Matching Instruction 1) Click the Channel Switching Button and Switch the Channel to Camera 1, and then press the Channel Switching Button for 3 seconds, then you will see the code matching notification on the monitor.
PAGE 6
3) The notification will disappear if the Code Pairing is successful, and the receiver starts to decode the image signal(usually takes 5 seconds). (Shown as below) You are going to view the image after the code pairing process is successfully done. (Shown as below) 4) Use the Same Method to complete the code pairing for Camera 2, Camera 3, or Camera 4. (If you have) 4. Image Display Switching.
PAGE 7
VI. Product Parameters: General Transmission Frequency: ISM 2.400-2.480 GHz Transmission Power: 15dBm Unobstructed Effective Range: 130m Outdoor/40m Indoor Spread Spectrum: FHSS Modulation Mode: GFSK Operating Temperature: 14-122 Fahrenheit/-10-+50 Celsius Operating Humidity: 85% Camera Imaging Sensor Type: CMOS Picture Total Pixels: 640*480pxl[NTSC] Minimum Illumination: 0lux[IR on] Night Vision Distance: 10m Lens: 6.
PAGE 8
[with antenna attached] Weight: VII. Troubleshooting: 1. Monitor Cannot display image: Please make sure the AV cable is well connected between the monitor and receiver, and make sure the power adapters for the receiver and the monitor are well connected too. 2. Flickering Image: Please check if the TV System of the camera kit is set same with your local TV system. 3. Pause Display A.
PAGE 9