Ltl Acorn Mobile Scouting Camera Ltl-5310 Series SMS remote control 720P video
USER’S MANUAL TABLE OF CONTENTS General Information.........................................................................................1 1.1 Features.................................................................................................1 1.2 Application............................................................................................. 2 1.3 Illustration.............................................................................................. 2 Quick Start........................
GENERAL INFORMATION Introduction This manual applies to model: Ltl-5310A Ltl-5310MC Ltl-5310MG Ltl-5310 WA Ltl-5310WMC Ltl-5310WMG. The Ltl Acorn 5310 Series (Model Ltl-5310A/MC and Ltl-5310MM) is the third generation of our Ltl acorn scouting camera. Bundled with the MMS-module (Multimedia Messaging Service) battery box (Part # LTL-MM1)standard scouting camera (Part # Ltl-5310MC) can be upgraded to work as a remote cellular camera.
x x x x x x x Serial Number setting enables you to code locations in the photos. This helps multi-camera users identify the location when reviewing the photos Built-in 2 ¼” TFT color display to review images and videos Date, time, temperature and moon phase can be stamped in the pictures Lockable and password protected MMS image sizes: 640 x 480 Users can configure the Camera and MMS function either by running the enclosed CD on the computer, or directly on the built-in TFT display.
LED IR Flash Light Sensor Motion Indicator Lens Prep PIR Sensor Main PIR Sensor Lock Hole Figure 1.1: Front View of Ltl-5310M Figure 1.
The camera provides the following connections for external devices: USB 2.0 port, SD card slot, TV out jack, and external DC power in jack. The 3-way Power/Mode Switch is used to select the main operation modes: OFF, ON and TEST. To power up the camera, install four NEW high-performance alkaline or lithium AA batteries in the camera. FOR BETTER PERFORMANCE, WE RECOMMEND USING ENERGIZER LITHIUM AA BATTERIES.
QUICK START 2.1 Insert SIM Card (Only for Model Ltl-5310MM) You need to purchase the SIM card from your local Mobile Phone Network Operators(MPNO), making sure they provide Multimedia Messaging Service (MMS). Ask them for the relevant information to configure the MMS settings on your camera.(Please reference 3.4 Set up MMS Function on PC in the Advanced Operation section.) Open the battery compartment cover, slide the SIM card in the slot and lock it. Figure 2-1 MMS-module Battery Box 2.
When battery level gets low, the Motion Indicator in the LED array will flash blue. On Model Ltl-5310MM, a “Battery Low” text alert will be sent automatically to the user’s cell phone or email account. 2.3 Insert SD Card The camera does not come with internal memory. So it will not work without a SD (Secure Digital) memory card or SDHC (High Capacity) card.
x x x Press the key to set the camera to take still pictures. Press the SHOT key to manually trigger the shutter. A photo or video (depending on the camera setting) will be taken and saved to the SD card. If the display shows “CARD PROTECTED” when you press the SHOT key, switch the power OFF, remove the SD card and slide its write-protect switch to off. Press the REPLAY key to review/playback photos/videos on the LCD screen, or a connected TV monitor. Use and key to navigate.
area of the prep sensors, the camera will power off and enter standby mode. 2.6 Advantages of Prep Sensors In general, to save battery power, an Infer-Red camera is in “sleep” mode, with only the PIR sensor working. When game is detected by the PIR sensor, the camera is powered on and starts shooting pictures. The time period from being activated to starting firing is called trigger time. The trigger time varies among different scouting camera brands in the market, generally from 1 to 5 plus seconds.
ADVANCED SETTINGS The Ltl Acorn trail camera comes with preset manufacturer settings. You can change the settings to meet your requirements. Please make sure the camera is in the test mode. 3.1 Parameter Settings Press “MENU” key to enter/exit the menu. Press , to move the marker, , to change the setting, and to confirm the change. Always remember to press to save the change. Otherwise you will lose your new setting.
Set Clock Enter Press Enter to set up date and time. Internal capacitor will retain the clock time for up to 7 minutes when changing batteries. 01 Photo, 02 Photos, 03 Photos Select the number of photos taken in sequence per burst in Camera mode. Please also refer to the Interval parameter. Avi 10 s, optional from 1s to 60s Videos are in AVI format that can be played back on most media players.
Timer 2 Off, On Select On if you only want the camera to work within a specified time period every day. For instance, if the starting time is set at 18:35 and the ending time at 8:25, the camera will function from 18:35 the current day to 8:25 the next day. Outside the time period the camera will not be triggered or take photos/videos. This feature can be used together with Time Lapse feature. Password Set Off, On Set up a password to protect your camera from unauthorized users. Serial No.
In the submenu, you can set the daily number of pictures sent via MMS. 0 stands for Unlimited. 199/Day gives you flexibility sending up to 99 pictures per day SMS remote control MMS Status 0, 1~24, Off represents the SMS receipt time, “0” indicates 10mins, “1~24” indicates the interval time 1~24h to receive SMS, “off” which turns the SMS remote control function off. Off, VGA, SMS The default setting is Off, which turns the MMS function off. To turn it on, choose either VGA or SMS.
from http://www.sendspace.
Set up the camera based on your need. Click on computer time. Click on Select Getime to retrieve the to choose the directory to save your settings, usually under the root directory of the SD card (You need to insert the SD card in the SD card reader and plug it in your computer.) Then, click on Generate . A file named menu.dat will be created and saved in the directory you just selected. If you selected a directory other than the SD card, you need to move the menu.
purchasing the MMS-module battery box (Part # LTL-MM1), skip the following step and go directly to 3.4 Set up MMS Function on PC. If your camera is Model Ltl-5310MC, the standard scouting camera, you’re done with the camera setting. Click on Exit to exit the interface. Retrieve the SD card from the computer and insert it in the camera. Switch to the TEST position to enter the TEST mode. A message will show up on the TFT display, indicating the Camera has been successfully set up.
First, you need to choose how you like to set up the MMS Mode --Auto or Manual. If you choose Auto, then you need to choose the country and the Mobile Phone Network Operator (MPNO). After doing that, the below section will populate with parameters pertaining to the selected MPNO, such as URL, APN, Gateway and Port. Then you can input the phone number and email address you’d like the MMS pictures to be sent to. You can enter up to three different phone numbers or email address.
If you choose Manual to manually input all the parameters, you need to contact your Mobile Phone Network Operator (MPNO) to have them provide you all the required information. Note: Because each local MPNO has their own settings for their MMS service, and those settings can change over time, we recommend you verify all the settings with your MPNO, even you choose Auto to let the system to configure the settings. We pre-store those settings for each major MPNO in the program on the enclosed CD.
03 Video size 04 Picture No 01 photo 03 photo 2 05 Video length 06 07 08 VGA(0), QVGA (1) ,720P 0 02 photo 1 1-60 indicates different value Interval beginning with S s represents Second, with M m represents minute 1-60 indicates different value Serial No off 0 on 1 take camera setting for reference figure+ letter PIR sense level Low 0 normal 1 High 2 , off (3) 09 Time Stamp 10 Side PIR 11 MMS status 12 Phone No 2 or Email Maximum 48 types 13 Phone No 3 or Email Maximum 48 types 14
All the order code ends with“*”, all the value ends with“#” EX: LTL01*0#02*2#06*S30#07*10A3Z#AA Definition camera mode 1.3MP interval:30s serial No: 0A3Z For SMS remote control setting, different value with different extra power consumption, “0” the highest, “off” zero. Maximum 60 bytes for all the SMS content, for multiple parameters setting please send by more times. Please do not send SMS continuously, send again only when you confirm the success of the last order by checking.
Select your language and the correct model from the drop-down list. Click on Smtp Setup, and you will see the following menu: In Auto mode, first select country and operator. In manual mode, you fill in APN / Account / Password. This parameter you can find from your mobile operator. Write in your E-mail server / port / sender E-mail / Password and Recipients E-mail.
SMS remote control, the value ranges from “0”to “off “which represents the SMS receipt time, “0” indicates 10mins, “1~24” indicates the interval time 1~24h to receive SMS, “off” indicates the close of the SMS remote control. Select the related value based on your own need. Then press save parameter to SD card, generate and insert SD card into camera and power on the camera, done. 3.
The Timer function is OFF. If you have the Timer ON, make sure you are in the specified time period when expecting incoming MMS pictures. Make sure MMS Status is not set OFF or SMS. The setting is “0”, or the daily limit has not been reached. If the daily limit has been reached, you can reset that number on your computer or on the TFT display. Then the daily limit starts to count from One. The camera is stationary while sending MMS pictures. 3.
CREG: SIM card is password-protected, or deactivated due to zero balance in the account, or not able to register with the GSM system. CGREG: Not able to register with GPRS network. COPS: Searching for the MNPO of the SIM card. Once it is found, the operator’s name and the signal strength will show on the screen. If No MM1 shows on the screen, it means the MMSmodule is not found (installed). Meanwhile the buzzer will be issued shortness three sound "di di di".
LTL-5310M SERIES PRODUCTS 4.1 Ltl-5310M Series Consists of Three Parts: 1. Ltl-5310M Camera 2. LTL-BM1 Standard battery box (without MMS-module) 3. LTL-MM1 MMS-module battery box 4.2 Models for Purchase: Ltl-5310MM = Ltl-5310M Camera + LTL-MM1 MMS-module battery box Ltl-5310MG=Ltl-5310MM+GPRS Ltl-5310MC = Ltl-5310M Camera + LTL-BM1 Battery box LTL-MM1 ----- MMS-module battery box Ltl-5310M Camera LTL-MM1 MMSmodule battery box LTL-BM1 Standard battery box IMPORTANT INFORMATION 5.
5.2 Power Supply and Battery Box Ltl-5310M Series camera can work on up to 12 voltages. The 4 AA batteries in the camera, the 4 AA batteries in the battery box, and the external power supply form a three-path parallel circuit. Each path is isolated from others and does not charge nor discharge others. As a result, the camera can extend its life in the field by being powered by an external solar panel. 5.3 SD Card There are plenty of different brand SD cards on the market.
thirty percent more full-length video clips. Besides that, when battery power gets low, our camera automatically shortens the video length so as to take more clips of more game. As a result, the total number of video clips doubles, even triples that of products of its kind, which provides users with more useful information. Note: Our camera performs at extreme cold environment as low as -30°C (-22°F), in which the battery power capacity deteriorates drastically.
5.7 FAQs on MMS Function x I set up a new receiving phone number. But the MMS pictures are still being sent to the old number. What should I do? Switch the camera OFF. Wait for at least two minutes. Then switch it ON. Or, switch the camera OFF. Take one battery out of the MMSmodule battery box, and then reinstall it. x Why did it take so long to receive the MMS pictures / why didn’t I receive any MMS pictures? The signal was too weak. Or the batteries ran out.
FIRMWARE UPGRADES 6.1 Firmware Upgrades The manufacturer reserves the right to upgrade the camera and the firmware. Follow the steps below to implement the upgrades: Install batteries and the SD card. Back up SD card contents. Format SD card on cmera. Retrieve the SD card and plug it in your computer (SD card reader may needed). Copy and paste the FW5310A. bin file in the root directory of the SD card.(Inquire the national distributor if there is an upgrade available and where to download it.
LIMITED WARRANTY We take great pride in our products. We always stand behind our promises. We provide a leading warranty term and service. Buying a Ltl Acorn product, you are covered under the limited warranty. We guarantee our products to be free of defects in materials and workmanship under normal use and service for a period after registered date of purchase.
6 30
Stand-by Current Stand-by Time Auto Power Off 0.4mA 3 6 Months 4xAA 8xAA Auto power off in 2 minutes while no Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes keypad controlling Power Consumption 150mA (+650mA when IR LED lights up) Yes Yes Yes Yes Low Battery Alarm 4.2~4.
Appendix II: PACKAGE CONTENTS Part Name Digital Camera Additional Battery Box TV AV IN Cable USB Cable Strap External DC Cable (optional) Installation CD Warranty Card Quantity˄Ltl5310MM˅ LTL-MM1 1 1 1 1 1 1 (With MMS module) 1 1 1 1 MMS-module battery box 0 1 (With MMS module) 0 0 0 0 1 1 1 1 1 1 Quantity (Ltl5310MC) 1 1 (Standard) 32
Appendix III: INSTRUCTION ON INSTALLING BATTERY BOX 33
FCC Statment This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.