Instruction Manual

Get to know us at: www.axvue.com
Please read the following instrucons and warnings carefully
Keep this instrucon manual for future.
For technical support see FAQ page.
For adult use only.
Adapters:
INSTRUCTION MANUAL
Model- E722
Revised at 12/2020
AXVUE E722 Video Baby Monitor
with 2.8'' LCD Screen and Two Cameras
The SCAN, SELECT, ADD, DELETE, VIEW CAMERA opons are only available when mulple
cameras connected with the monitor. Order extra cameras by vising us at
www.axvue.com or search “Axvue Baby monitor” on Amazon.
1. LED*
2. Microphone
3. Power/Video
4. Talk Back/Zoom
5. Volume Up/Up
6. Menu/OK
7. Right
8. Volume Down/Down
9. Le
10. Speaker
11. Baery Compartment
12. DC Jack
13. Kickstand
× 3× 1 × 2
Power & Low Baery Sound Lights
*LED
Keep the distance between sensor
and body at least 0.6 inch for
accurate temperature result.
1. Night-Vision LED
2. Lens
3. Microphone
4. Speaker
5. Power/Code
6. Temperature Sensor
7. DC Jack
8. Wall Mounng Hole
0.6 in
Monitor:
TO USE PORTABLE/BATTERY MODE
Step 1: Charge the baery for at least 8 hours before using portable/baery mode.
Step 2: Make sure the adapter is plugged into camera.
Step 3: The baery life can be up to 10 hours if it is fully charged.
Baery life will be shortened if recharging it connuously. Unplug the power adapter when you are
not using it for a long me.
Please charge the baery for 6
~
8 hours before using the product.
TO USE PLUGGED-IN MODE
Step 1: Place the monitor display in living room, bedroom or any place you want to watch your baby.
Use adapter to connect camera with electrical outlet.
Step 2: Turn on monitor by pressing
Power/Video“ ” buon for 6 seconds unl axvue logo or video
shows up on the screen.
Step 3: Press
Power/Video“ ” buon to turn off the video if you only need to hear the voice.
Step 4: Turn off the monitor completely by pressing and holding
Power/Video“ ” buon for
5 seconds.
The monitor and camera are paired before shipment. If it is unpaired for some reason, please refer
to the following steps:
TO PAIR MONITOR AND CAMERA (ADD CAMERA)
Step 1: Make sure the camera and monitor are in the same place.
Step 2:
Step 3:
Make sure the power adapter is plugged into
camera and turn on the camera by pressing
Power/Code“ ” buon for 6 seconds.
Turn on monitor by pressing
and holding Power/Video
“ ” buon for 6 seconds.
６
Step 5:
Step 4:
Red LED flashs
vox
TEMP
C
F
13 24
13 24
4
2
3
1
65
Press
Press
SETUP & USE
3 feet
Figure 1
3 feet
Figure 2
Please charge the battery for at least 8 hours before
using the product.
Step 1: Test recepon first, put the camera in a suitable place that
will provide you the best view of your baby in the crib (Note: Do
not hang up the camera firmly unl the inial installaon test is
completed). Plug the adapter into the wall outlet and turn on the
camera.
Step 2: Turn on the monitor by pressing and holding the Power/
Video “ ” buon for 6 seconds unl “axvue” shows up, then the
video will show up on the screen immediately. If the video does
not show up, please refer to “TO PAIR MONITOR AND CAMERA
(ADD CAMERA)” on the next page. If the video shows up, the
inial installaon test is completed, then you can set up the
camera according to the instrucon below.
Set Up Camera: Place the camera on a flat surface, such as a
wardrobe or shelf (Figure 1). Or hang it on the wall (Figure 2). No
maer wherever to place the camera, please make sure to keep it
away from the crib for at least 3 feet and all power cords should be
placed behind the camera properly. Then adjust the angle of the
camera lens unl the enre crib shows up on the display, or adjust
it to the best angle that you think to watch your baby.
-Store this product out of the reach of babies (at least 3 feets (0.9 m)
away from the crib). A strap wound around the baby’s neck may result in
asphyxiaon. Use a safety clip to clamp the power cord and keep it out
of baby’s reach. Do not use other extension cords. Only use the power
adapter provided.
-Do not touch the exposed part if the adapter is connected with power.
-Test regularly before inial use or when change the posion of camera.
-Avoid placing the product in humid place or contacng with liquid. (such as bathtub, sink, etc.)
-Do not apply heat to the product.(such as stoves, radiators, etc.)
-Using the product in venlated place. Avoid placing it on sofas, cushions, beds or other places which
may block venlaon.
-The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are
contained, please be careful when unpack and install it.
THIS PRODUCT CAN NOT SUBSTITUE PARENT’S SUPERVISION
ON YOUR CHILD.
WARNING
-Only use the recommended rechargeable baery. Please contact us if you need to change it.
For the contact list, please refer to the last page of the instrucon.
-Please clean the baery compartment before using it.
-Avoid short circuits the power supply terminal.
-Remove the baery when you are not using it or when running out of power.
-Keep the baery away from children.
-Dispose of the empty baery properly.
BATTERY WARNING
FEATURES & COMPONENTS
Camera:
６