User's Manual Part 1

ManualsBrandsShenzhen Kirisun Communications ManualsElectronicsFM Handheld Transceiver

Transmitting

Lights red

Receiving Lights green when Carrier wave is present

Scanning Flashes green. (Once per second.)

Read/Write frequency

Read frequency: flashes red; Write frequency:

flashes green.

Transmit code (DTMF

/2-Tone/5-Tone)

Flashes orange after transmission.

(Once pe

second.)

Decode (DTMF/KDC

1200/2-Tone/5-Tone)

Flashes orange within the effective time

after receiving the correct code.

Low battery warming

Flashes red. (Once per second.)

Alerts once every 30 seconds.

Wireless clone

Turn on the transceiver with PTT and side

button 2 pressed, and lights orange.

While in cloning the host transceiver flashes

Red and the sub one lights green.

3.5 Installing the Optional Speaker/

Microphone

Insert the

Speaker/Microphone plug into

the jacks of

the versatile connector, and

fix it with the supplied snail

screw.

Notes:

1) Only use the KIRISUN

Speaker/ Microphone.

2) KME-62A Speaker/Microphone is

supplied for option.

3) The Speaker/Microphone is

for option only. If you

want to purchase one,

please contact the local

KIRISUN dealer.

4 GETTING ACQUAINTED

4.1 Transceiver Overview

3 Channel Selector

Rotate to select channel 1-16.

4 Power/Volume Switch

Turn clockwise to switch on the transceiver.

Turn counterclockwise till a click is heard to switch off the

1 Antenna

2 LED

Indicator

transceiver.

Rotate to adjust the volume after turning on the transceiver.

5 Side Button 1

Programmable function button: Press it to activate the programm

Summary of content (18 pages)

PAGE 1
3.5 Installing the Optional Speaker/ Microphone Insert the Speaker/Microphone plug into the jacks of the versatile connector, and fix it with the supplied snail screw. Lights green when Carrier wave is present Decode (DTMF/KDC Flashes orange within the effective time 1200/2-Tone/5-Tone) after receiving the correct code. GETTING ACQUAINTED 1 Antenna 2 LED Indicator Receiving Transmit code (DTMF Flashes orange after transmission. (Once per second.) /2-Tone/5-Tone) 4.
PAGE 2
7 8
PAGE 3
6 7 8 PTT (Push-to-talk) To make a call, press and hold the PTT button, then speak into the microphone with normal voice. Release the PTT button to receive. Side Button 2 Programmable function button: Press it to activate the programmable auxiliary function. Its default setting is squelch off Momentary. Emergency Button Press and hold it longer than the preset time to activate emergency alert function. 9 Microphone/Speaker Jacks For connecting external Microphone/Speaker. 4.
PAGE 4
cannot use it. If you selected a channel not opened LED will lights red and flashes green, and warning tone sounds. Make a Call To make a call, press PTT, and speak in normal voice and pleas e keep your mouth 1~2 inches aw ay from the microphone to get the best voice quality. Release the PTT button to receive a call. Receive a Call Your dealer can set CTCSS, DCS, DTMF, KDC1200, 2- Tone and 5- Tone signaling on your radio channels by PC software.
PAGE 5
11 12
PAGE 6
the scan function has been activated, the transceiver can start scanning. 1) Press the button set as Scan or Scan + Temporarily Delete to start scanning. 2) The transceiver will start scanning from the current channel and scan channels one by one in the consequence of channel No. and the LED flashes green. 3) When a signal is detected on a channel , scanning pauses and LED lights green. 4) You can select a channel to make a call by pressing the PTT button during anytime of scanning.
PAGE 7
without manual 13 operations.
PAGE 8
dealer, and you have to be equipped with the specified headset earphones. Before using VOX, you must set VOX gain level. Such setting enables the transceiver to identify the voice volume. If the microphone is too sensitive, the background noise will trigger the transceiver to transmit. If the microphone is not sensitive enough, it cannot receive your voice when you speak. Make sure to adjust VOX gain level to proper sensitivity. 1) Connect the headset earphones with the transceiver.
PAGE 9
seconds, and turn on the transceiver at the same time entering Clone Mode. 1) When the clone slave ,s entering clone mode, LED lights orange and you will hear voice annunciation Clone . When release buttons, voice annunciation Channel 1 sounds. 2) When the Clone master entering clone mode, LED lights orange and you will hear voice annunciation Clone . When release buttons, voice annunciation Channel 1 sounds. 3) Select on the Clone master the channel number identical with that on the Clone slave ,s.
PAGE 10
time required for holding the button may be different. When the transceiver enters emergency call mode, it will switch to the emergency channel automatically, and starts transmitting according to the dealer's setting. Transmitting and receiving recycle can be set by your local dealer. 2) To exit the emergency call mode, press again and hold the emergency call button.
PAGE 11
consumption. 7.3 Low Battery Warning Low battery warning tone sounds and LED flashes red when the battery power goes below a certain value, and you need to recharge or change the battery. In low battery status transmission is prohibited. 7.4 Voice Annunciation of Channel Number The dealer can activate or inactivate this function by programming. While switching to another channel, you can hear the voice annunciation of the current channel number.
PAGE 12
3) Option signaling: When the channel you select is busy before valid option signaling matches, or when the channel you select is busy and programmed CTCSS/DCS signal is not detected before valid option signalin g matches , the transceiver is unable to transmit. 7.6 Clear Tail Tone When using the channel set with CTCSS/DCS, the after sound in talking ending can be eliminated. 7.7 Remote Kill The dealer can activate or inactivate this function by programming.
PAGE 13
19 20
PAGE 14
transmit. After releasing PTT button indicator flashes orange and then you can talk to other transceivers until the effective time expires when the indicator turns dim. 7.10 KDC 1200 The dealer can activate or inactivate this function by programming. 1) Receiving Signals: When receiving the signal consisting of your ID and fleet code, squelch will be activated, and call can be received and LED flashes orange.
PAGE 15
2) Transmitting Signal: If the PTT ID on the channel you select has been set with 5 Tome, 5 Tone signal will be transmitted when making a call. Or transmit 5 Tone signal by pressing CALL1 or CALL2 button, which can be set by the dealer. 7.13 Transmitting Beginning/Ending Signaling 1) Transmitting Beginning/Ending signaling is used to join in or disconnect from some repeaters and telephone. 2) Transmitting Beginning signaling is used to join in the conventional repeater and its relevant auxiliary equipments.
PAGE 16
No. 5 PROBLEM Communication range is too short. Unable to 6 transmit. 7 Noise is too loud. S OLUTION Make sure the antenna is well connected. Make sure the antenna is the original supplied one. Check if the battery power is in the normal state. Ask your local dealer to adjust the squelch level. Make sure the PTT button has been pressed completely. Battery power may be insufficient. Recharge or replace the battery pack.
PAGE 17
10 Settings (by the Dealer) Model: 1) Serial No.
PAGE 18
CE Versions of the PT620 0 whic h display th e "CE" symbol on the serial number seal, comply wit h the essential requirements of t h e Eu r o p e a n Ra d i o a n d Telecommunication Terminal Directiv e 1999/5/EC. This warnin g symbol indicates tha t this equipment operates in nonharmonised frequenc y bands and/o r may be subjec t to licensin g conditio n in the countr y of use.