User's Manual

ManualsBrandsShenzhen Kirisun Communications ManualsElectronicsFM Handheld Transceiver

User Manual

PT568

FM HANDHELD TRANSCEIVER

We are very grateful for your purchasing

brand two-way radios produced by Kirisun

Electronics (Shenzhen) Co., Ltd.

We believe

two-way radio, which always incorporates the latest technology, can bring

great convenience to your life and work.

We also believe that the quality and function of

two-way radio can meet your

demands for reliable communication.

Notice to the User:

* Government laws prohibit radio communication without permission in areas dominated by

the government.

* Illegal operation is subject to punishment by fine and/or imprisonment.

* Refer service to the well-trained professional technicians only.

Safety

It is important that user is aware of and understands hazards common to the operation of any

radios.

Warning!

Turn off your radio before entering any area with a potentially explosive atmosphere (where

the air contains gas, dust and smog, etc.), such as while taking on fuel, or while parking at a

gasoline service station.

Precautions in Use

Please comply with the following attentions to avoid fire, bodily injury and damage to the

radio.

* The radio is recommended to transmit for 1 minute and receive for 4 minutes. Long time

transmitting or continuous working in high power mode will make the rear side of the radio

generate heat.

* Please do not disassemble or assemble the radio under any circumstances.

* Please do not expose the radio to direct sunlight for a long time; do not place the radio near

any heating devices, either.

* Please do not put the radio in extremely dusty, moist or dabbling places; do not place it on

any unstable surface, either.

* If the radio emits smoke or strange odors, turn it off and remove the battery from the radio

Summary of content (15 pages)

PAGE 1
User Manual PT568 FM HANDHELD TRANSCEIVER We are very grateful for your purchasing brand two-way radios produced by Kirisun Electronics (Shenzhen) Co., Ltd. We believe two-way radio, which always incorporates the latest technology, can bring great convenience to your life and work. We also believe that the quality and function of two-way radio can meet your demands for reliable communication.
PAGE 2
and contact your local authorized Kirisun dealer without delay. Contents 1. Open Package Inspection 2. Preparation 2.1 Charge the battery 2.2 Install/Remove the battery 2.3 Install the antenna 2.4 Install external speaker/MIC 2.5 Install the belt clip 3. Radio Overview 4. Basic Operation 5. Functions of Programmable Buttons 6. Auxiliary Functions 7. Wired Clone Mode 8. Troubleshooting Guide 9. Major Specifications 10. FCC Notice 1.
PAGE 3
Antenna Intelligent Charger Adapter Belt Clip Strap Battery 2. Preparation 2.1 Charge the battery Insert the cable plug of the adapter into the jack at the back of the charger. Then insert the adapter into an applicable AC power output socket. The three LEDs will flash for about one second, and then the green LED will be constantly on when the charger is normal. Insert the battery to be charged or the radio into the charger. Do remember to turn off the radio before inserting it into the charger.
PAGE 4
and the charger is in the protected status, in which you should not charge the battery compulsorily. Please remove the battery and cut the power of the charger. Note: * The radio battery has not been charged when leaving the factory; please charge the battery before using the radio for the first time. * Both KB-56A lithium polymer battery and KB-56B lithium polymer battery of the company are applicable to this radio.
PAGE 5
To remove the battery, please push the latch at the lower end of the radio forward, the lower part of the battery will bounce up automatically. Then, loose the belt clip slightly and remove the battery. Note: Please avoid short circuit of the battery terminals and do not throw the battery into fire. Do not tear down the shell of the battery by yourself. 2.
PAGE 6
3. Radio Overview 1. LED indicator Solid red — The radio is transmitting. Solid green — The radio is receiving. Blinking red — The radio is in low battery. 2. Channel selector knob Rotate the knob to select channels 1-116. 3. Power/Volume control knob Rotate the Power/Volume control knob clockwise until you hear a click to turn on the radio, and counterclockwise until you hear a click to turn it off. If the radio is on, turn the Power/Volume control knob clockwise or counterclockwise to adjust the volume.
PAGE 7
① Powering up the radio Rotate the Power/Volume control knob clockwise to turn on the radio. If the dealer has set the alert tone, a sound of “Bee” will be heard. ② Adjusting the volume Press the preprogrammed “Squelch Off” button to hear background noise. Then rotate the Power/Volume control knob to adjust the volume. ③ Selecting a channel Rotate the channel selector knob to select the required channel. When correct signals are received, you can hear sounds from the speaker.
PAGE 8
⑤ Receiving Release the button, the radio will return to the receiving status. The dealer may have programmed CTCSS/DCS signaling in your radio. On the channels with CTCSS/DCS signaling programmed, you can only hear calls from other radio with the same CTCSS/DCS. 5. Functions of Programmable Buttons The dealer can assign one of the following auxiliary functions to the top button, side button 1 or side button 2. No. Function Description 0 None No function is assigned.
PAGE 9
10 Monitor Press the preprogrammed “Monitor” button to disable CTCSS, DCS signaling, and you can receive signals that cannot be heard under normal operation. Press it again to resume normal operation. 11 Momentary Squelch Off Press and hold the preprogrammed “Momentary Squelch Off” button to open squelch; release it to resume normal operation. 12 Squelch Off Press the preprogrammed “Squelch Off” button to open squelch. Press it again to resume operation.
PAGE 10
radio is not capable of transmitting signals. 6.4 Voice Announcement This function can be enabled or disabled by the dealer. There are two languages available: Chinese and English. If changing the channel by channel selector knob, the radio will announce the number of the selected channel after the selection is finished. 6.5 CTCSS/DCS The dealer may have programmed CTCSS or DCS signals on channels of the radio. Through this, other irrelevant calls using the same channel can be ignored.
PAGE 11
stay at the priority channel; if there is no signal, it will return to the original channel. c) The revert channel (Tx channel) during the scan can be designated by the dealer. There are following options available: Scan start channel: The radio will transmit signals on the channel for which the scan list applies. Scan start channel + Current channel: If the scan is paused, the radio will transmit on the current communication channel.
PAGE 12
7. Wired Clone Mode If the wired clone function is enabled, the radio will not quit automatically after entering the Wired Clone Mode. To return to normal user mode, the user needs to restart the radio. The operating steps go as follows: 1. Press side button 2 to turn on the radio and enter Clone Mode. If the wired clone function is disabled, the radio will enter User Mode. 2. Connect the slave radio with the master radio by a clone cable. Then turn on the slave radio. 3.
PAGE 13
5 The red LED (Tx) lights up, but no sound is heard A. The power module is broken, so there is not power output. Please change it. B. The microphone is broken, please change it. 6 The green LED (Rx) lights up, but no sound is heard. A. The speaker is broken, please change it. B. the audio amplifier is broken, please change it. 9. Major Specifications General Specification PT568 Frequency 136-174MHz, 400-450MHz, 420-470MHz. Channel number 16 Channel spacing 25kHz(broadband)/12.
PAGE 14
Only”. In addition, your KIRISUN radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. American National Standards Institute (C95.
PAGE 15
Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure.