DR600T,DR600T-01
User Manual DR600T, DR600T- 01 Digital Transceiver We are very grateful for your purchasing Kirisun DR600T,DR600T-01 digital transceiver maufactured by Kirisun Communications Co., Ltd. We believe Kirisun DR600T,DR600T-01 digital transceiver, which always incorporates the latest technology, brings great convenience to your life and work and meets demands for reliable communication.
Notice ◆ Please carefully read this instruction manual before using the product for your easy operation. We will consider that you have read this manual once you use the product. ◆ Please carefully keep this manual for future reference. ◆ In order to protect your legal rights from infringement, please carefully fill in the warranty card and claim valid receipt. ◆Kirisun and its authorized partners own the intellectual property of all the parts of this product (including accessories).
Safety Precaution ◆The radio can only be repaired or maintained by professional technicians. The user must not disassemble the radio at liberty. ◆The settings and installation shall be approved by local radio management department. ◆Lightning protection is required when installing the transceiver antenna. ◆Please use qualified power supply, antenna, thunder preventer, feeder and other accessories during installation, otherwise the transceiver may be damaged.
Contents 1 Unpacking and Checking ........................................................................................................... - 1 - 1.1 Accessories ........................................................................................................................ - 1 2 Overview .................................................................................................................................... - 3 - 2.1 Power Switch ....................................................
1 Unpacking and Checking Please carefully open the box and make sure the items listed below are included. For items missing or damaged during delivery, please contact the local dealers for help. 1.
Transceiver: Power Cable： - 2 -
2 Overview - 3 -
No. Part Name 1 Handle 2 Fan 3 Indicator 4 Power Switch 5 Ground Interface 6 100-240V AC Inteface 7 13.
2.1 Power Switch Press this button to power on/off the transceiver. 2.
2.2.1 PIN Description Pin Description PIN1 DC 13.6V Output PIN2 Ground Cable PIN3 Null PIN4 Null PIN5 Null PIN6 Null PIN7 External PTT Signal input, High level active .
PIN16 Null PIN17 Ground Cable PIN18 External Analogue Audio Input PIN19 Ground Cable PIN20 High level electrical signal output PIN21 Squelch is on when it is connected to PIN20 and it is used for testing PIN22 Null PIN23 Null PIN24 Null PIN25 Null PIN26 Null 2.2.2 External Interface Description • To Activate the External PTT Connect PIN7 and PIN20 of ACCY interface to activate the external PTT, and you can test the TX signal of transceiver.
address to the IP on the label, but the data of them are not changed. After re-boot, the configured IP address and gateway address will be recovered. 2.
3 Basic Operation 3.1 Power on /off Transceiver When the transceiver is off, press the power switch or the system starts to operate, and the indicator the power switch to power it on. When the indicator glows, will indicate the default work mode. Press to power off the transceiver when it is on. 3.2 Connect to the Controller After connected with the controller, the indicator sending to the controller, and glows.
3.5 Emergency Alarm The emergency indicator glows during abnormal situations, for example, when RX frequency lost lock, the emergency indicator flashes every one second and when TX frequency lost lock, two seconds. When both TX and RX frequency lost lock, the indicator glows constantly. Please turn to professional technician for help when abnormal situations happen. 3.6 Programming Software Please check the network status before programming the transceiver.
If the channel information is newly created or read from the transceiver, the save path should be selected (similar to “Save as”) . Save as: choose a path to save the configuration. Exit: exits the programming software. 3.6.2 Radio Type Radio Type: select transceiver for radio type. Frequency 136-174MHz，400-470MHz are available, or you can define fr equency band yourself. The self-defined frequency band should be within the available range. 3.6.
transceiver does not accept other calls. After the call hang time is over, the call ends and the channel resources will be released. Value range: 0~7000 milliseconds; step value is 500 milliseconds; 4000 milliseconds by default. Emergency Call Hang Time: after an emergency call is initiated, and if no PTT button is pressed on both parties, the transceiver will keep call hang time for the terminals. During the call hang time, the transceiver does not accept other calls.
used as server, the local monitor port should be configured and the slave device is connected to system network through this port. When it is used as slave device, the serve IP(or domain name) and port should be configured. Network Time Slot Configuration: both two time slots can be equipped with or without network. In case of network status, the internet time slot ID should be configured. When the transceiver is networked, it will determine whether it should transmit data according to network time slot ID.
the specified threshold, the power amplifier will be disabled automatically. 85℃ by default. Fan Enable Threshold Temperature: when the temperature is higher than the specified threshold, the fan will be turned on automatically. 40℃ by default. Fan Disable Threshold Temperature: when the temperature is lower than the specified threshold, the fan will be turned off automatically. 30℃ by default. Standing Wave Ratio: used to test whether the antenna is well matched with transmitter. Default value: 3.0.
(2) The carrier cannot be selected for mixed channel receiving. It must choose CTCSS, CDCSS or –CDCSS. 3.6.4 Programming Menu Read: read data from transceiver. There will be a progress bar indicating progress during the reading process, and you can set to automatically exit the data window when the data is fully read. Write: write the configured data into transceiver.
Wrong transceiver IP entered on the programming software or the user forgets transceiver IP. B. Transmission Failure Check if the frequency configuration between the portable and transceiver is the same and whether their modes are matched. 5 Parameters Frequency Range: 136-174MHz ，400-470MHz AC: 100-240V@2.5A 50/60 Hz DC : 10.8-15.6V@15A DC Insurance: 13.6V15A AC Insurance: 2.5A 250VAC, 5x20mm Insurance Type: HRC ceramic, Time lag (T) Supplied Power: 200W TX Power: 40W(UHF) / 45W(VHF) Size: 482.
RF Energy Exposure Compliance ƽ Your radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy. This radio complies with the FCC RF exposure limits for occupational or controlled RF exposure environment and is authorized by the FCC for occupational use only.
Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note:” Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.” This device complies with Industry Canada licence-exempt RSS standard (s).
DR600T Digital Transceiver User Manual - 17 -
