MT02S User Manual GPS Tracking sulutions PRODUCT MANUAL S h e n z h e n K i n g w o I oT C o . , Ltd .
Declaration The contents of this manual will be updated from �me to �me without prior no�ce; the updated content will be added to the new version of this manual. KINGWO will improve or update the products or procedures described in the manual at any �me. If there is a descrip�on of the product in the manual that does not match the actual product, the actual product shall prevail. KINGWO has the final interpreta�on rights of this manual.
CONTENTS 01 03 02 04 03 09 04 10 05 17
01 Production Intruduction Product Feature 1 / Support GPS/Beidou, AGPS, LBS,with accurate posi�on performance； 2 / Built in high sensi�ve G-sensor accelerometer. 3 / Supports intelligent self-diagnosis, intelligent power save mode, remote fuel and power cut off, OTA and alarm func�ons. 4 / Small in size and wide voltage, especially designed for scooter, motorcycle, electric vehicles and automo�ve financial risk control project. 5 / Small and convenient for conceal installa�on.
02 Function Func�on-Posi�on Posi�on and Monitor Including �mely upload, blind zone compensa�on, speed mileage sta�s�cs, area monitoring and other func�ons, the backend sends posi�oning commands, and the terminal uploads data including longitude, la�tude, speed, direc�on, and status informa�on. Timely Monitor The device can be set to upload the posi�on and status informa�on of the vehicle to the backend at a certain �me or a certain period or at a certain �me interval.
LBS If GPS is not available, the device will automa�cally switch to LBS mode, and acquire the LBS each 30s and upload the based informa�on, the server shall interprets the specific loca�on on the map. AGPS The device supports AGPS, once the device is connected to GPRS, the AGPS can be used to speed up the posi�oning and improve accuracy. Alarm Func�on Low Voltage Alarm When the ba�ery voltage on the vehicle is too low (0-11V or 19-22V), device will report a low voltage alarm to the backend.
Towing alarm An alarm is generated when the device is set to a displacement of more than 100 meters (message mode prompt), and the alarm informa�on is reported when the displacement radius exceeds 100 meters when the device is turned off. (Note: displacement range 100~2000m) The device will send SMS if the vehicle is moved in igni�on off status, if the radius is more than 100 meters, will upload towing alarm.
Self-Diagnosis The device can perform self-diagnosis. In case there is malfunc�on regarding GPS and GSM, it will report error message to the backend, and the backend .The backend can query the current model, version, configura�on, running status, and device func�ons. Sta�c Dri� Suppression The device has a built-in high-sensi�vity G-sensor accelerometer and a complete posi�oning data-filtering algorithm that filters out most of the sta�c dri� data to ensure the accuracy of GPS data.
switches to the standby server. The primary server and the standby server can be set in either IP or domain name.
03 Parameters Main Unit Characteristics Description Working Voltage DC 9V-36V，applicable to12V/24V vehicles Average current<40mA（DC12V）， Working current Maximum current<100mA（DC12V） Sleep current<10mA Built in ba�ery Ba�ery protec�on 110mAH,3.
04 Installation guide ①【Installa�on and debugging process 】 Switch SIM card Red LED Status: Fast Blink:GPRS Connec�ng Slow Blink:GPRS connected Solid on:Module Error Green LED Status: Solid on:GPS Posi�oned Blinks:LBS Posi�oned Off:Unposi�oned
Open the top cover of the device Insert SIM card into SIM card holder SIM card installa�on Open the top cover of the device, insert the prepared SIM card into the SIM cardholder, and then confirm that the SIM card bu�on is in place. Please make sure that the SIM card has the GPRS func�on enabled in advance and know the SIM card number. Main Unit power on A�er installing the SIM card, turn the ba�ery switch to the ON posi�on.
白色 Fuel Ignition Switch Fuel yellow orange black gules 2A fuse Battery ②【Terminal connec�on】 Terminal connec�on Turn off the ba�ery switch and connect the power line to the corresponding signal line of the vehicle in turn according to the defini�on of wire material. A�er the above connec�on, the blue light of the device indicator light is always on (flickering) and the red light is slowly flashing, indica�ng that the power supply is normal.
③【Recommended Installa�on place 】 Under front windshield Seat sponge Around dashboard Near the headlights Under the back seat Under rear windshied Inside the taillight cover or the plas�c component Note: Make sure the equipment is on-line before installa�on.
④【Parameter se�ng by SMS 】 Note: The device is with unique ID number, the factory can preset t IP, port and APN, generally do not need to do parameter se�ng; if you need to modify the IP, follow the below instruc�ons, make sure the SIMs has SMS func�ons available: HC,,,# Set the upload interval in real �me tracking mode: T1: upload interval in igni�on on status, range,5-300s ,default 15s T2: Upload interval in igni�on off status ,range 5-300s, default 120 s T3：Sleep return interval, range 10-180
LOCKACCOFF,A# Set vehicle lock A=0 Receive lock command, execute immediately A=1 Receive lock command, if ACC is off, execute immediately, if ACC is on, store this command un�l ACC off A=2 Store the command, lock vehicle from ACC Off to On, if the communica�on is well, lock vehicle, otherwise wait for next turn For example：LOCKACCOFF,0# means execute the lock command immediately a�er receiving it APN,apn,user,pswd# Set APN, User name and password For example：APN,CMNET,internet,internet# APN:CMNET Username: in
16 IP2,ip or dns,port,type# IP2,119.23.233.52,9881,1# Set the backend server IP:119.23.233.52,port 9881，communica�on type is TCP IP2,www.365qczx.com,9881,0# Set the backend server domain:www.365qczx.com，port 9881，communica�on type: UDP IP2,,0,0# Delete backend server parameter Usage Requirements The terminal is strictly forbidden to use according to the opera�ng instruc-�ons ,disassemble, collide, charge, soak, over 80 °C, human failure, force majeure damage, etc.
17 CONTACT US Shenzhen Kingwo IoT Co.,Ltd. +86 0755 86704262 marke�ng@kingwoiot.com www.kingwoiot.com/ www.365qczx.net 7 F, Building A, Tsinghua Informa�on Hi-tech Park, North District, Science Park, Nanshan District, Shenzhen City, Guangdong Province, 518052, P.R.
