User's Manual

Dismantle bottom cover method figure ：
2. Installation Guides
3. 1. The host uses 3 pcs AAA alkaline battery, normal usage 1~3 months;
Standby (continuously): ~ 6 months.
3. 2. WL03C: 1 pc 27A (12V) alkaline battery
WL09C: 1pc CR2032(3V) button battery
normal usage more than 1 year (Assume: 5 times usage/day)
3. 3. Operating environment temperatures: -20~+60℃
3. 4. Operating environment humidity : R/H <80%
3. 5. Storage temperature: -30℃~+70℃
3. Operating Guides
2.2.6 Battery low power indication
2.2.6.1 When the host is at low battery (3.3V) condition, a weak
“Du..Du..” 2 times sound was generated when use ARM or DISARM
and requires to replace the battery immediately
。
2.2.6.2 When the remote control’ s flashlight becomes dark /fade or
remote control range becomes shorter, it indicates the battery power
is low and replaces with a new battery accordingly
。
Figure of bottom cover removal method:
Figure of bottom cover removal method:
2.2.2. Touch Sensivity Level, Volume, SOS setting feature
2.2.2.3
Setting method
*
*
*
*
size:75x75mm 英文 正面
1 2 3
Install location
Cautions:
● Pay attention on host fixation method suitability, double-sided
tape or cable tie when use it.
● Install at a hiding location may reduce host alarm sound level.
● Do not install the host at surrounded with metal parts location.
Disarm
Disarm
Arm
Arm
Double-sided
Tape
Double-side
Tape
Cable Tie Hole
Cable Tie hole
Ringtone
/Switch
Ringtone
/Switch
Bell
Bell
Remote control have two below types according to order package set
(Host front & Back ) (Install location figure)
Bottom
screw
User Manual
Remote Alarm / Displacement Sensor Alarm
1. External Structure Figure
Triaxial
Accelerometer
Sensor
7 Levels
Sensitivity
KS-SF22R
Long Standby
Time
Emergency
Help Function
113 dB
Loud Alarm
2. 2. Application and Setting
Motorbike/Bicycle Anti-Theft Alarm
2.2.1 ARM & DISARM
2.2.1.1 Press once time on remote control [ ] key in standby
mode, the host produces “Do..Le..Mi” sound and enter into ARM
mode， after 5 seconds, a ‘Bi ’ sound and enter into alert mode. Any
touch or hit is occurred at ARM alert mode, the host will trigger the
alarm immediately for 2 seconds, detect on any touch or hit again
within 2～ 12 seconds, the alarm will continue for 30 seconds (one
ringtone type for 2 seconds alarm; 6 ringtones types for 30 seconds
with automatic switching)
。
2.2.1.2
Press remote control [ ] key once at alert situation, the
host will produces once “Mi..Le..Do” sound and signals the host was
exited from alert mode already
。
2.2.1.3
When the host is still alarming, direct press remote control
DISARM key to stop and exit from ARM mode simultaneously
。
2.2.2.1
Touch sensivity has 7 levels from high to low, 7 ringtones
sound prompt, Do, Le, Mi, Fa, So, La, Di; Volume has 3 levels,high,
medium and low
。
2.2.2.2 SOS is an internationally popular feature and off mode at
factory default setting. Note that the SOS function will recognize the
installation state of the host,so please do not change the installation
direction again after complete the installation, otherwise it may cause
Press and hold remote [ ], the host will continuously prompts the
disarming sound (please ignore the sound) until remote LED light off
and on again before release the hand. The host enters into setting
feature
。
To adjust the sensitivity level, press [ ] key continuously from
high to low in cycle with seven adjustable levels
。
To adjust the volume, press [ ] key continuously from high to low
in cycle with 3 adjustable levels
。
In case of the SOS function is turned off, press the [ ] key once,
the host will “Bi” sound once to enter into the calibration mode, and
then “Bi. Bi. Bi. Bi. Bi.” 5 beeps are correct calibrated, and the SOS
function is successfully turn on; Otherwise two long “Bi… Bi” sounds is
a calibration error and fail to turn on (The host shall be placed in static
mode before performs the SOS calibration)
。
In case of the SOS function is turned on successfully, press the [ ]
key once, long“Bi” sound twice to turn off SOS function. After complete
the settting, press [ ] key, the host will exits the setting function
。
the function to fail or be abnormal. After the SOS function is turned
on, it will automatically call of when the bicycle is tilted more than
45degrees by accidentally. After corrected back the bicycle to the
original position, it will turn off the call of automatically.The SOS
trigger sound is in accordance with international conventions/stan-
dards
。
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This
device must accept any interference received,including interference
that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment gener-
ates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user's
authority to operate the equipment.
2.2.5.3 Decoding method: Be cautious when use this function! At
first, confirm the host is not at ARM mode; Long press for coded
remote control [ ] key to enter into the code learning mode. After
once ‘Bi’ sound, press [ ] key with “Bi … Bi … Bi ” 3 times sound,
the host will delete all coded addresses. Please refer to above
method for new code learning
。
2.2.5.4 Be cautious of the host can caters up to 8 remote controls
coding only, the first registered remote control coding will be removd
if exceeds 8 remote controls registration
。
2.2.5.1 The first remote control code learning method: At first,
remove the host batteries and install back after 30 seconds. Long
press remote control [ ] key to enter the code learning mode. After
the host produces once “Bi” sound, press ARM or DISARM key with
twice “Bi..Bi..” sound, you should able to use new added remote
control already
。
2.2.5.2
To add more remote controls code learning method :Press
old remote control’ s DISARM key to disarm at first, then,long press
at old remote control [ ] to enter code learning mode, After once
‘Bi’ sound, press new remote control’ s ARM or DISARM key with
twice “Bi…Bi” sound, you should able to use new added remote
control already
。
2.2.2.4 The host changes the batteries, sensitivity level and volume
setting momeries will be stored. Because of SOS may needs to
recalibrate, so it will automatically turn off
。
2.2.3 Bell Ringtone switching function
Press [ ] key, 3 ringtones to choose and cyclic beeping (ARM
mode can not use)
。
2.2.4 Bell and search function :
Press bell key and trigger select-
ed bell ringtone to find the motorbike/bicycle easily
。
2.2.5 Remote control Learning Code
2.1 Host battery replacement and installation
2.1.1. Factory will install the battery by default. If the battery requires a
replacement or installs new batteries, please follows below figures
method by open bottom cover, install 3 pcs AAA alkaline battery.
The host produce 3 times short ‘Bi’ sound and indicates turn on and
use the host directly; Recommend disassemble the battery if it does
not use for long period of time。
Remove the host’s 1pc bottom screw and use minus (-) screwdriver to
open bottom cover by rotate or turn around. After open the bottom
cover, continue to open side of the cover until it is easily dismantled by
hand. If do not have minus (-) screwdriver, can try use a solid film or
shim to open as show in above figure。
2.1.2. It is recommended to avoid installation in locations where
exposed to long-term and high-temperature sunlight. Too high
temperature will accelerate battery self-discharge and shorten battery
life. Please replace the battery in time when the battery is low,
otherwise there is a risk of liquid leakage and damage to the host。
● External: Domineering power with tiger form styling and acts a
safeguard device to motorbike or bicycle.
● Similar performance to motorbike alarm, 113dB loud speaker
although install at a hiding place to frighten the thief/robber.
● Use triaxial accelerometer sensor and special calculation to
increase accuracy of robber manner recognition and reduce false
alarms caused by noise interference.
● High efficient with 7 adjustable level of sensitivity, from soft touch
to push beat and suitable for all conditions.
● 3 ringtones for remote bell sound；long range remote and easy
to search the motorbike/bicycle.
● Can trigger SOS function and emit call for help automatically
when an accident is occurred to provide more safeguard manner.
● Wireless remote operation; more simple and convenient to use.
● External Cover : PC material; IP55 water & dust proof
● Double-sided tape installation method is convenient for all types
of motorbikes and bicycles.
4202001008 V1.1
FCC ID:2ANPS-KS-WL09C
2020.07
WL09C
WL03C
2020.07-- 更新加了一款遥控器