IPC I21AN Shenzhen Kean Digital Co., Ltd.
Packaging list: Note:Some camera models don’t have separate antenna(fixed) Installation procedures: Begin Connect Hardwares Install the Search Tool Login the IP Camera in Lan Wireless Settings Login the IP Camera On PC Client Access By Mobile End Note:For the first time use IP Camera,please refer to the procedures
above Connect the Camera with Internet cable and power accordingly as above 2.Install the Search Tool Open the CD,Install the following software: 1.
2. Open the File “JW & HW series”-”Browser View”: Copy “Search Tool ” to desktop and run it 3. E-View7 App Installation APP Download Please Download and install the E-view7 APP before you set up the IP Camera. Search on Google Play store or APP Store for “E-view7” One Key Setting Function (cell phone must be connected to the WiFi. ） Step1.Connect the camera with power adaptor (you do not need to connect the Ethernet cable). Step2.
1 Step3.Enter the correct WiFi password, then click on “Start configuration”, like shown in the screen below: 2 3 Step4. Wait for 60 seconds, then choose the respective device and enter the password. If done, click on save to connect to the WiFi.
Method 1:Input the P2P ID, User name, Password of your camera manually. Then click “Save” Method 2:Scan the QR code:Click the “Scan QR code” button,at the bottom of the camera, there is a label of QR Code, then scan the QR code with your smart phone,it will show the ID, input the user name and password, then click “Save ” Method 3:Click “Search”, then you will get the local camera list in your phone.
9 10 After wifi connection, the camera will be rebooting, You will find the camera online after 3-5 minutes The video will be showed wirelessly,refer to Picture 11and 12 11 12 4.
be showed automatically.（Before viewing camera on IE, you must set One Key Setting） Note:If the Search Tool shows subnet mask does not match,please click Double click the camera IP address in the search tool.
Note: If the OCX installed before,then login directly A. Click “OCX” to download and Install it. B. Refresh the webpage and login again,the camera video will be displayed as below Live video . 5.
1).Click , access the “ Device imformation” settings 2)Checking the imformation of the ipcamera 6.
7.Time Setting 1).Click , access the “time” setting 2)You can choose the NTP server you want,and click “Apply” 3)Choose the time zone you want,click “Apply”,you can get it 8.
Record & Capture Path: Where to store the files, video and photos. (If you can’t choose this, pay attention to your PC OS and IE version, please use the IE browser.) Record file length: At least 100MB Record time length: At least 5 minutes. Reserved disk space: If your pc disk space is less than 200MB, stop recording. Record cover: Delete the old files when the disk capacity is almost depleted.
Finally, Paste IP address of the camera in IE browser, Click “Enter” and find the below page then you can modify the video path : 9.Record Schedule This section explains the SD card recording settings. If the SD card has been inserted, the capacity of the card will be displayed. But at first, you need to format it. It includes: Record coverage, Record time, Timer recording.
Record coverage: Delete old files when the SD card is nearly full. Record time: Create a video file every 10 minutes. Timer recording: Set the time, select all, store recording to the SD card. You can playback the video online with IE browser.
10.Mail Service Settings and Alarm Service Settings 1). The Mail service settings are a requirement for the alarm function. If your camera will be activated it will send you an email with photos attached. For this, you must assure that the mail service is configured correctly and successfully tested. Here an example for Gmail. It will send an email if the camera is activated.
You must enter the following information: Sender: Enter your email address Receiver: Enter your email address or a different email address SMTP user: Enter the email username SMTP password: Enter your email password Note: This function only works if the IP camera is accessed via the network. If you use Gmail, the port should be configured as 465, SSL should be TLS. The most important, make sure that your Gmail has SMTP enabled.
11.Ftp service setting and system Log FTP setting: 1).
12.
Wireless Setting 1).Click , access the “Wireless” settings 2).Search the WIFI signals and choose the SSID you want 3).Make sure all the parameters are the same as your router, input the WIFI network key. 5).Click “check”, after 30seconds,one notification will show you if the WIFI settings succeed 6)If succeed, just go back to select “Apply”, then disconnect the network cable Note:If the camera IP Address can not be found on the search tool.
13.Rtsp&Onvif 1)Support onvif function and Rtsp function 14.
15.
16.Upgrade Device Firmware 2). With this option you may reboot the camera, restore it to the factory settings, and upgrade the system. 17.Access By Mobile E-View7 App Installation A. For IOS (iPhone/iPad),download App “E-view7” in App Store; For Android phones, download App “E-view7” in Google Play, our official website or you can get it from CD Path:”JW & HW Series”-”Mobile App”. B. Also support scan the App QR-code in the user manual to download directly. Mobile View A.
1. 2. Three methods to add IP camera: Method 1:Input the P2P ID, User name, Password of your camera manually. Then click “Save” Method 2:Scan the QR code:Click the “Scan QR code” button,at the bottom of the camera, there is a label of QR Code, then scan the QR code with your smart phone,it will show the ID, input the user name and password, then click “Save ” Method 3:Click “Search”, then you will get the local camera list in your phone.
B.Live video 7.FAQ : A.Forget the password 1)Reset your camera, you should press the RESET button for 10 seconds when the power is on(for indoor camera,it’s on the bottom of the camera, for outdoor camera , the white reset button is at the end of the power cable). 2)Finishing reset, the camera will restore to factory settings, the user name is”admin”and password is none. B.
1.Close the firewall of your computer. 2.Change the ActiveX settings,“IE” browser > “Tool” > “Internet Options” > “Security”> “Custom Level” > “ActiveX control and Plug-ins”,all the ActiveX options set to be “Enable”: Especially: Enable:Download unsigned ActiveX controls Enable:Initialize and script ActiveX controls not marked as safe Enable:Run ActiveX controls and plug-ins a.
b. FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
