SIntelligent network camera User Manual
Safety Regulation FCC Requirement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EU Request Statement The product and attached accessory should meet the safety regulations of CE and have “CE” sign. In addition, it should comply with the listed applicable Uniform European Standard in EMC Directive 2014/30/eu, which is 2014/35/eu, RoHS Directive 2011/65/eu. 2012/19/eu (WEEE Directive): In European Union, the product with this symbol cannot be handled as unclassified municipal waste.
Accessories Instructions NO.
Installation Instruction 1.Cut off the power 3.Adjust cross plate to make it horizontal, fasten the cap head screws. 2.Install cross plate to junction box. 4.Use adjustable holder, adjust the length of cap head screws on cross plate.
5. Use hook to pull out the wire in the junction box. 6.Connect the corresponding wire and bare copper wire with wiring cap, make sure to screws. 7.Put the light through cap head screws on cross plate, adjust its position, fasten the decorative fixture nuts. 9.Turn the power on. 8.Install light bulb. 10.Debugging.
APP Installation Step 1: Download and install 'Annke Light' APP from APP Store or Google Play. Step 2: Click “Annke Light” open. Step 3: Sign up with e-mail address. Step 4: Log in with e-mail address and password. ② ③ ① APP User registration APP user login WiFi Connection: Step 1: Click “add camera” Step2: Click “add by WIFI” Step 3: Enter device name and click scan QR code. Step 4: Scan QR code. Step 5: Use needle push the “SET” button for one second to reset.
⑹ ⑷ Scan QR code. ⑸ Use needle push the “SET” button for Configure WIFI, input the password. one second to reset. ⑺ Click “NEXT”, APP will search device automatically until connection ⑻ ⑼ When LED light turns green, it means After connection, the monitor connection is completed. view is live. Wireless Connection (QR connection) Step 1: Click “add camera” Step2: Click “add by WIFI” Step 3: Enter device name and click scan QR code. Step 4: Scan QR code.
⑴ ⑵ ⑶ Configure WIFI, input the password. Click “add camera” Click “add by WIFI” Enter device name and click scan QR code. ⑹ ⑷ Scan QR code. ⑸ Use needle push the “SET” button for one second to reset. Configure WIFI, input the password.
⑼ ⑻ ⑺ Put QR code in front of the camera When LED light turns green, it After connection, the monitor within 5-10 cm. If the scan was means connection is completed. view is live. completed, you can hear “beep” sound. Network Table Connection: Step 1: Click “add camera” Step2: Click “add by network table” Step 3: Enter device name and click scan QR code. Step 4: Scan QR code.
⑹ ⑸ ⑷ Scan QR code. After scanning, APP will After connection, the monitor search device automatically view is live. until connection, Wireless Connection (add share with friends) Step 1: Click “add camera” Step 2: Enter device name and click scan QR code. Step3: Click “add share with friends” Step 4: Scan QR code. Step 5: After scanning, APP will search device automatically until connection, Step 6: After connection, the monitor view is live.
⑸ ⑷ Scan QR code. ⑹ After scanning, APP will search After connection, the monitor device automatically until view is live. Software Reset Step1: Log into the APP, click connected device, enter into device preview image, tap to enter setting screen Step2: Tap Reset (The bulb will turn on, and you will hear “Ding Ding Ding” sound, finally the Led will turn to red and flashes) Step3: Reset successfully.
Reset button Step1: Press the reset button 5-10 seconds with needle at the bottom of the Fixture. (The bulb will turn on, and you will hear “Ding Ding Ding” sound, finally the Led will turn to flashing red.) Step2: Reset completes.