User's Manual

ManualsBrandsShenzhen Junlan Electronic ManualsElectronicsBluetooth Soundbase

2.1CH TV Stand Bluetooth Sound Base Speaker

MODEL:ITSB-350

1 X Remote Control

1 X Instruction Manual

1 X RCA Cable

1 X 3.5mm Aux In Cable

ITSB-350ITSB-350

Press the button on the unit or press the SOURCE button on the remote

control repeatedly until "BT"appears on display.

optical in.

Optical-In

FCC Warning:

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be

installed and operated with minimum distance between 20cm the radiator your body:

Use only the supplied antenna.

-- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that

may cause undesired operation.

PLAYING AUDIO VIA OPTICAL-IN SOURCE

TV; DVD player; BD player... etc.

Rear view of the unit

2. Power on the unit as previous procedures.

3. Press the button on the unit or press the SOURCE button on the

Remote Control repeatedly until "OPTI" appears on display.

4. Power on the connected external player and start playback the Music as usual.

1. Connect the Optical out jack from the external audio Player (such like TV, DVD Player

BD Player …etc.) to the OPTICAL IN jack on the top of unit by the Optical Connection

Optical Connection Cable ( not supplied )

Cable (not supplied) as the figure below: ( F or PCM format only )

Turn on the digital audio output and set it to PCM (Plus Code Modulation) type

similar to the follows figure:

Bass

Treble

Balance

Select

Move

Exit

Sound Mode Standard

Surround Off

AVL Off

Audio Language English

Picture

Time

Setup

Lock

Off

AudioAudio

Digital Output PCMDigital Output PCM

OPTICAL

FRONT VIEW

5 6

7 8 9 10

TOP VIEW

REAR VIEW

12. AUX IN JACKS(L/R)

13. OPTICAL IN JACK

14. ANTENNA WIRE

OPTIC AL

OPTICAL

11. DC IN JACK

1. SPEAKER

4. POWER Button

5. SOURCE Button

8. TUNE UP/NEXT Button

9. VOLUME DOWN Button

10. VOLUME UP Button

2. DISPLAY

3. REMOTE SENSOR

6. PLAY/PAUSE/PAIR Button

7. TUNE DOWN/PREVIOUS Button

9. MO/ST(Mono/Stereo) Button

3. SOURCE Button

4. PAIR Button

2. VOL(volume)- Button

6. TUNE- Button

12. TUNE+ Button

5. EQ (equalizer) Button

7. Button

8. FM SCAN Button

13. PRE/RECALL Button

STANDBY

PAIR

TUNE-

TUNE+

MO/ST

11. VOL(volume)+ Button

FM SCAN

10. MUTE Button

PRE/

RECALL

8. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it

can cause severe internal burn in just 2 hours and can lead to death. Keep new and used

batteries away from children. If the battery compartment does not close securely, stop using

and keep it away from children. If you think batteries might have been swallowed or

placed inside any part of the body, seek immediate medical attention.

Folloe these precautions when using a battery in this device:

1. Use only the size and type of battery specified.

2. Be sure to follow the correct polarity when installing the battery as indicated in the battery

compartment. A reversed battery may cause damage to the device.

3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc ) or old

batteries with fresh ones.

4. If the batteries in the device are consumed or device is not to be used for a long period of

time, remove the batteries to prevent damage or injury from possible battery leakage.

5. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture.

( Follow battery manufacturer's instructions.)

6. The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

7. Clean the battery contacts and also those of the device prior to battery installation.

6) If the available FM station is stereo, the unit will plays it in stereo mode

automatically.

If the reception is no good, press the MO/ST button on the

Remote Control to switch it

to Mono mode. Press again to turn back to

Stereo mode.

listen the desired preset channels.

To store the band automatically, press FM SCAN button on remote

control , the unit will scan all available band and store

automatically.

then stop and play).

to search the specific

available band back and forth

5) After finishing scanning, press "PRE/RECALL" button on remote control

repeatedly to select and

2) Press the button on the unit or press the SOURCE button on the

Remote Control repeatedly until FM frequency appears on display.

3) Press /TUNE- or /TUNE+ button on remote control(or press

or button on the unit) repeatedly

band.

automatically the

Press and hold the TUNE - or TUNE + button on remote control

(or press and hold the or button on the unit),

the unit will search

The TV STAND SOUND BASE

the TV STAND

SOUND BASE

Press the button on the unit or press the SOURCE button on the remote control

repeatedly until "BT"appears on display.

the TV STAND

SOUND BASE

ITSB-350ITSB-350

while

playing, press "PAIR " Button on

remote control or press and hold the Button on the unit to cut off

current pairing, then try to connect the other BT device following above steps.

If you want to connect another BT device

~ Press the

Press the /TUNE + or /TUNE - button to skip the tracks.

button on the remote control

~ Press the

EQ button on the remote control to set to JAZZ, POP, ROCK,

CLAS and NORM mode.

or press the button

on the unit to pause, press again to resume.

OPTICAL

(DVD or VCR...etc)

red

white

1. Connect the Aux out jacks from the external audio player (such like DVD player,

VCR …etc.) to the AUX IN jacks on the rear of the unit by the supplied RCA

connection cable as the figure below:

2. Connect the unit to the power as previous procedures.

3. Press the Standby ( ) button on the unit or Remote Control to power on

the unit.

4. Press the button on the unit or press the SOURCE button on the

Remote Control repeatedly until "AUX" appears on display.

5. Power on the connected external player and start playback music as usual.

or +

correct source appears

or -

Type of Optical Digital Audio in ........................................................................ PCM

is a trademark on a registered trademark of Bluetooth

SIG Inc. All other trademarks and trade names are

those of their respective owners.