Installation Guide

Night Light Installation Guide
APP Smart Motion Night Light
( Plug Version)
PPA”efilruF“ eht tcennoC50
Download APP
Searching "Furlife" in the app store or scan the QR code of
the manual to download and install the app.
If you are downloading and using the app for the first time,
;tnuocca ruoy retsiger ot nottub ”retsigeR“ eht kcilc esaelp
.nottub ”nigoL“ eht kcilc ,tnuocca na evah uoy fi
Using Device
Connect the device to the power source and make sure the
phone is connected to the 2.4GHz WiFi network.
Light Facade
Light Bottom
Plug
Button
Off Shut
WIFI
Auto People Infrared Sensor
01Product Introduction
Luminous Place
Lighting Sensor+ Infrared
People Sensor
charging indicator
bedroom
02Product Advantage
Smart APP Control/WiFi Communication Protocol
Natural Soft Light/ Can be Constantly Bright Or Off
Small and Exquisite/Lighting Sensor+ Infrared People
Plug-in design eliminates battery replacement
Ultra Low Power/120 ° Sensing Angle/Dark Light On
5-7 Meters Sensing Distance / 15S Continuous Lighting
03Applicable Scene
For example：
corridor
living room
bathroom
kitchen
Variety of Application Scene，
corridors, stairs, bedrooms,
living rooms, kitchens,
bathrooms, wardrobe lockers,
etc。
Tip：Keep away from water
and heat sources.
05 Connecting the Furlife”APP
Open the app to the "My Home" page and click on
"Add Device";
Add the device
Select "Night Light" in the "Device List" and add by
following the prompts;
Network reset
05 Connecting the Furlife”APP
eht elggot ylsuounitnoc dna egap ”eciveD ddA“ eht ot oG
dluohs lavretni ehT(.”iFiW-FFO-iFiW-FFO-iFiW-FFO“ hctiws
eht ,)no thgil eht litnu ”FFO“ eht sserP ,trohs oot eb ton
lamp body starts to flash and the reset is successful, and
the device is in the networkable state;
Click the "Confirm light is flashing quickly" button; enter the
WI-FI password and click confirm;
08Precautions
This product is only suitable for safe use in areas below
2000 meters above sea level
This product is for indoor use only. Do not use it in humid or outdoor
This product is not a toy, please keep children away from this device
Unplug the power before cleaning the product. Do not use liquids,
spray cleaners or wet cloths for cleaning
Keep away from water and heat sources while using. Do not cover the
Light body to avoid the damage to the product and pose a safety
hazard
09FCC WARNING
06Product Specification
07Product Certification
Product Name： APP Smart Motion
Night Light( Plug Version)
Product Type：SNL-003-S fireproof
material: ABS+PC fireproof material
Light Body Color:Warm/ Cold white
Input Voltage:5V
Output power ：light:0.6W,colourful
light:1.2W
Light Source Type: LED
Color Temperature: 3000K-3200K
/6000K-6500K
Power Supply: AC 110V-240V
U
L
R
04Using
The Sensing Range Front View
In the dark environment, the built-in human body sensor of the
night light can detect human activity in the sensing range and
trigger the night light to illuminate. The sensing range is a
120-degree fan area that is unfolded in the center of the front
of the night light, 5-7 meters in front and 2-3 meters in side.
The sensing effect is related to the ambient temperature, body
shape, and moving speed.
Tip：The use of night light and infrared sensing function can be
affected during the day or when the light source is strong.
120°
5-7m
2-3m
(side)
(front)
Push the button to Auto by hand,
the night light is automatically
sensedaccording to the light and
infrared body.
(*this function is only suitable for
dark environments)
Push the button to WiFi, the network
mode is on (No need to reset the
network for the first time);
Push the button to OFF by hand，
the night light is off;
04Using
05 Connecting the Furlife”APP
Connect the device (the device cannot Powered off in the
process of connecting);click the "Finish" button after the
device is added successfully;
The device can be found in the "My Home" list after the
device is added successfully.
You can adjust the lantern mode in the APP page
*
05 Connecting the Furlife”APP
ni ”edoM ytilibitapmoC“ kcilc ,egap ”eciveD ddA“ eht ot oG
the upper right corner, turn off the power after 10 seconds,
FFO-iFiW-FFO-iFiW-FFO“ hctiws eht elggot ylsuounitnoc dna
”FFO“ eht sserP ,trohs oot eb ton dluohs lavretni ehT(.”iFiW-
until the light on), confirm the night light flashes quickly
(twice per second), operate again: toggle switch "OFF-WiFi-
OFF-WiFi-OFF-WiFi" until the light body starts to flash slowly
(two seconds) , the reset is successful and the device is in the
networkable state;
Click the "Confirm light flashing slowly" button; enter the
WI-FI password and click to confirm;
Network reset (compatibility mode)
05 Connecting the Furlife”APP
Connect the device (the device cannot Powered off in the
process of connecting);click the "Finish" button after the
device is added successfully;
The device can be found in the "My Home" list after the
device is added successfully.
You can adjust the lantern mode in the APP page
*
说明书单页尺寸：78x78mm
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.