Quick Start Guide * Thanks for purchasing and using our product. Please read this quick start guide before using, and keep it for future reference. * Menu contents are subject to change without notice in accordance with our policy of continuios product improvement.
1. what’s in the box Please consult below checklist for all the components. USB Cable Video Doorbell User Guide Screw & Tools Indoor Chime Double-sided Tape 2. meet the doorbell 3 1 2 10 4 11 5 6 7 8 12 1 2MP Camera 7 Charging Indicator 2 PIR Motion Sensor 8 Micro USB Port 3 Speakers 9 4 Indicating LED 10 Wall-mount bracket Reset 5 Doorbell Button 11 SD Card Slot 6 Microphone 12 Battery Compartment 9 3.
5. Battery charging The batteries inside the doorbell are not fully charged in accordance with transportation safety regulations. Please charge the batteries with a USB compatible wall charger (not included) and the provided USB cable for about 8~10 hours prior to Wi-Fi configuration and installation. 6. Download the app Download and install the 'CloudEdge' app from Google PlayTM or the App StoreTM.
8. run a test After setup, tap on the live view window in the app for a test. Then take your doorbell outside to the installation spot and run a test there. Make sure the installation spot is covered by strong 2.4 GHz Wi-Fi signal. Note: If the video quality from the doorbell outside is not as good as it was indoors, you may need to move your router closer to your installation spot, or invest in an Wi-Fi extender.
9. Live view interface 1 Quit live viewing 8 Wi-Fi signal status 2 Setting menu 9 Screenshot button 3 Battery status 10 Speak to the scene 4 Volume on/off 11 Record on the phone 5 HD/SD switch 12 Body detection on/off 6 Full screen view 13 Notification history 7 Stream bit rate 14 Cloud storage service HD 10.
11. Installation Select location 140° Your doorbell has 140-degree view angle and 120-degree human detection range. It is suggested to mount your doorbell at least 5 feet (160 cm) above the ground for the best angle of view and motion detection performance.
12. connect the chime supply power to the chime The chime can be powered by an USB compatible phone charger (DC5V 1A). You can also plug the chime to the USB port on your PC/notebook to supply power. (not included) (not in clude 1. Powered by DC5V adapter (phone charger). d) 2. Powered by PC USB Port. Pair with doorbell 1. Tap on “···” and enter into Settings, select Wireless Chime.
Select ringtone Enter into Settings->Wireless Chime, there are 4 ringtons available(See to Picture.3). Volume control Enter into Settings->Wireless Chime, and you can control the volume level for the chime(See to Picture.3). Unbind 1. Press and hold reset button on the chime for about 5 seconds till the indicator flashes blue twice, and the chime will be restored to factory default. 2. You can also tap on “unbind” (See to Picture.6) in the APP to release the connection between doorbells and wireless chimes.
14. Specification Video doorbell Video & Audio Image Sensor Indoor Chime General 1/2.7” CMOS (2.0MP) Hisilicon Lite-OS Power source DC 5V 1A OS Power port USB (Type-A) Resolution 1920 × 1080 px Consumption 0.2W Stream HD/SD dual stream Ringtones 4 ringtongs optional Infrared LED High power IR LED with ICR Volume Max 100dB Lense 1.7mm/F2.0 Volume control Low(mute), middle, high Angle of view 140° Connection type Radio frequency Min. illumin. Color: 0.01 Lux; B&W: 0.
FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.