Baby Monitor model：iBabyⅠ (Ver.1.0) Shenzhen Jinghua phase control Co.
iBabyI - Baby Monitor Contents 1. Summary......................................................................................................................................... 2 2. Electrical characteristics and parameters.................................................................................. 4 2.1 Angle and distance of Detection .......................................................................................... 4 3. Major function..................................................
iBabyI - Baby Monitor Summary iBabyI is using 60G millimeter wave radar technology to realize human respiratory heart rate perception and sleep assessment. The module is based on the FMCW radar system, aiming at the output of the respiratory heart rate frequency of personnel in specific occasions, combined with the long-time sleep posture body motion acquisition, and timely reporting the record of personnel's sleep state and history.
iBabyI - Baby Monitor Electrical characteristics and parameters Sleep detection distance (anocelia) 0.4 2.5 m Respiratory and heartbeat detection distance (anocelia) 0.4 2.5 m Respiratory measurement accuracy Respiratory measurement range 90 0 Heartbeat accuracy Ranges of heartbeat measurement 23 % 54 90 0 Refresh time Detection establishment time 74 % 120 time/min 0.12 S 1.5 S Voltage (VCC) 4.
iBabyI - Baby Monitor Radar operating range The beam coverage range of the radar module is shown in Figure 3. The radar covers a three-dimensional sector area of horizontal 60 and pitch 60. Affected by the beam characteristics of radar, the action distance of radar in the normal direction of the antenna surface is relatively far, but the action distance deviated from the antenna normal direction will become shorter.
iBabyI - Baby Monitor Sleep detection function a. Detection distance: 2.5m (detection distance between human and radar antenna surface) The b. Sleep quality assessment function: awake / light sleep / deep sleep c. Sleep time recording function: the data output of the relevant duration of sleep quality d. In bed function: in / off bed a. Detection distance: 0.4m≤x≤2.5m (detection distance between chest cavity and radar antenna surface) b. precision:≥90% a. Distance measurement: 0.4m≤x≤2.
iBabyI - Baby Monitor within 1.5m to ensure that the radar can normally detect breathing, heartbeat and sleep-related parameters. The radar normal direction is aligned with the main detection position to ensure that the main beam of the radar antenna covers the human sleep detection area land within certain boundaries. The radar normal direction is aligned with the main detection position to ensure that the main beam of the radar antenna covers the human sleep detection area land within certain boundaries.
iBabyI - Baby Monitor 1) Detect there is anyone in the room； 2) Measure people’s Heart rate and respiratory rate； In this mode, for the accuracy of the environmental state judgment, the state output logic of the radar module is as follows: A. Only when the radar equipment detects the status change, it has the corresponding status output of the radar; otherwise, the radar remains silent; B.
iBabyI - Baby Monitor of the bed, and tilted downward to 45 pairs in the middle of the bed, to ensure that the distance between the radar and the human body is within 1.5m, and to ensure that the radar detection range can normally cover the sleep area. This module is mainly used in scenarios such as health management or home enabling. The following explains the application mode of typical scenarios.
iBabyI - Baby Monitor Based on the detection characteristics of the sleep state and breathing rate of the sleepers, the radar can be better used in a healthy life, including: a. Intelligent health single product linkage application b. Household electrical appliances Because the module needs to completely reset the internal circuit of the module, and the environmental noise is fully evaluated, to ensure the normal operation of the module.
iBabyI - Baby Monitor the target. This module does not have the ranging function temporarily, so it is normal for the effective detection range to fluctuate in a certain range. Because human biometric features are ultra-low frequency and weak reflection characteristic signals, radar processing needs a relatively long time of accumulation processing. In the accumulation process, many factors may affect radar parameters, so the accidental detection failure is a normal phenomenon.
iBabyI - Baby Monitor the product without notifying the users, and we will make no promises and guarantees in any legal sense. Encourage customers to comment on recent updates to the product and support tools. The components and devices mentioned in this document are references to the information published by the copyright holder company, and the right to modify and publish it belongs to the copyright holder company.
iBabyI - Baby Monitor Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
