Quick Start Guide

Connect the mobile phone
or computer to the Wi-Fi.
Account Password
Quick Start Guide
FRL-W5A
FARLINK FRL-W5A
This document is for reference only and does not
constitute any form of commitment.
Step 1: Wire the device
FARLINK FRL-W5A
Connect to
the power
supply.
The network cable
can connect to any
Ethernet port.
LAN port
Router or fiber optic
modem / common
modem
*The FRL-W5A itself does not provide the routing function and needs to connect to a router
or a fiber optic modem or common modem with the routing function.
Step 2: Connect Wi-Fi
FARLINK_5G_XXXX
WLAN
Connected
FARLINK_2G_XXXX
Initial password: 12345678
FARLINK AC2100 wireless intelligent networking terminal
Model: FRL-W5A
Rated voltage of power: 12V 1.5A
Management system: farlinkwireless.com (scan the QR code)
Management address: 192.168.1.100
User name: admin
Password: admin
Wi-Fi name: Farlink_2G_XXXX
Farlink_5G_XXXX
Initial password: 12345678
SN: XXXXXXX1234 MAC: AABBCCDDXXXX
Reset hot key: Hold down the key for five seconds until the indicator flashes in red.
Then, the system restarts automatically and restores to the factory configuration.
Farlink Electronic Technology Co., Ltd. Manufactured in China
*The device generates two Wi-Fi names by default, and the last four characters of the names
are the same as those of the device MAC address.
Step 3: Access the management system
Scan the QR code at the bottom of the device or enter
farlinkwireless.com to access the device management system. If the
device is not connected to a router, enter 192.168.1.100 in the
browser.
User name/Initial
password
Login
Account:
Password:
Management system: farlinkwireless.com
Management address: 192.168.1.100
*When the device is not connected to a router, ensure that the IP address of the mobile phone or
computer is in the 192.168.1 network segment, and then configure the device.
Change the Wi-Fi name
and password
Wi-Fi setting
2.4G/5G signal merging
5G Wi-Fi name
5G Wi-Fi password
2.4G Wi-Fi name
2.4G Wi-Fi password
Save setting
Change user name
and password
Save setting
Account:
Password:
After configuration, connect
the mobile phone or
computer to the Wi-Fi again.
*The 5G signal has strong anti-interference capability. It is recommended to generate 5G and 2.4G
signals separately and use 5G signals preferably.
For a large house, villa, or
loft, it is recommended to
use multiple devices for
mesh networking to
expand the coverage.
*Select a proper number of devices and the deployment locations based on the house type and area. *Perform the same operations for more relay nodes.
Mesh networking
Press the WPS key on the device to set up mesh
connection to expand the coverage
Router or fiber
optic modem /
common modem
Root node
Press the buttons of the root node and relay node at the
same time, and then the indicator flashes in green . When
the indicator stops flashing, mesh connection is set up.
Relay node
Step 4. Configure Wi-Fi Coverage expansion
Find the Wi-Fi name on the nameplate
at the bottom of the device.
Indicator
Indicator
Indicator Color
Green steady on
Orange steady on
Red steady on
Green flashing
Yellow flashing
Orange flashing
slowly
Status Description
The device is in normal running.
The device is starting.
The device is not networked or the uplink is
disconnected.
The WPS configuration is started or the software is
being upgraded.
The bandwidth of the accessed network is 10/100M or
the return wireless signal is weak.
The device is triggered to perform resetting or restore to
the default setting.
*Hold down the indicator button for more than three seconds to turn on or off the display of the indicator light.