Preface Thank you for purchasing HYT TC-310 Business Two-Way Radio. It adopts ergonomic design to bring you excellent user experience, and is applicable for a variety of industries such as hospitality, property management, retail, entertainment and manufacture. This easy-to-use radio will deliver your secure, instant and reliable communication at peak efficiency. Please read this manual carefully before use. The information presented herein can help you to derive optimum performance from your radio.
Icon Information The following icons are available through this manual: Warning/Caution: represents important safety information, to make users aware of misoperations that may cause malfunction of the radio, personal injury or property damage. Note: indicates important information which helps you make better use of your radio. Copyright Information HYT and CRS are registered trademarks of HYT in P.R.C and other countries and/or areas. HYT retains the ownership of its trademarks and product names.
Contents Safety Information ............................................................................................................. 3 Product Inspection ............................................................................................................ 4 Radio Overview................................................................................................................. 5 Battery Information.............................................................................................
SAFETYTRAINING INFORMATION Your HYT radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only”.
ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the HYT belt-clip which is listed in instructions when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side.
OPERATING NOTES When transmitting with a portable radio, hold the radio in a vertical position with its microphone 5 to 10 cm (2 to 4 inches) away from your mouth. Keep the antenna at least 2.5 cm (1 inch) from your head and body. If you wear a portable two-way radio on your body, ensure that the antenna is at least 2.5 centimeters (1 inch) from your body when transmitting.
Product Inspection Please unpack the package box carefully and check that all shipped items are received; report any missing or damaged items to your dealer. Accessories supplied with the radio Item Qty. (PCS) Antenna 1 Strap 1 Belt Clip 1 Li-Ion Battery 1 Switching Power 1 Owner’s Manual 1 Antenna Li-Ion Battery Switching Power Strap Belt Clip Note: Frequency band is marked on the label of antenna; if not, please refer to the label on the radio unit for frequency band information.
Radio Overview (1) Strap Hole (2) Power On/Off Key (3) Antenna (4) Volume Control Key [+] (5) PTT (Push-to-Talk) Key (6) Volume Control Key [-] (7) Programmable Function Key (8) Microphone (9) Channel Selector Knob (10) Channel Mark (11) Status Indicator (12) HYT Logo (13) Charge Indicator (14) Speaker (15) Accessory Cover (16) Model Label (17) Audio Accessory Jack (18) MINI USB Port (19) Screw for Belt Clip (20) Battery (21) Belt Clip (22) Charging Piece (23) Battery Latch ﹡PTT (Pus
Note: Short Press means key press shorter than 1 second, while Long Press means key press longer than 1 second. ﹡LED Indicator Status indications and alert tones are shown in the table below: When the radio is turned on, an alert tone sounds and the Status Indicator flashes orange once. Power On (to enter User Mode) When the radio is currently on a blank channel, it sounds beep tones continuously. When the radio is turned off, the power-off alert tone Power Off is heard.
from low power to high power. VOX Compandor One beep sounds when the feature is enabled. Scrambler Two beeps sound when the feature is disabled. Channel Lock ﹡Battery Latch Used to secure or remove the battery. ﹡Audio Accessory Jack Used to connect audio accessories. ﹡Mini USB Port Used to connect accessories such as programming cable, cloning cable and switching power.
2. When charging the battery that is attached to a radio, turn the radio off to ensure a full charge. 3. Never charge a wet battery or a wet radio with battery attached. Please dry it with a soft cloth prior to charge. 4. The battery will eventually wear out. When the operating time of a fully charged battery is noticeably shorter than its normal performance, you need to buy a new one. Please replace it ASAP. 5.
self-discharge. Charging the Battery With a battery-attached radio, when the Status Indicator flashes red, and an alert tone sounds at an interval of ten seconds indicating the battery power runs low, please charge the battery immediately. Only use the charger specified by HYT. The Charge Indicator will indicate the charging progress as follows: Please follow steps below to charge the radio with switching power: 1. Plug the AC connector of the switching power into an AC outlet socket. 2.
Please follow steps below to charge the radio/battery with a desktop charger: 1. Plug the AC connector of the switching power into an AC outlet socket. 2. Plug the Mini USB connector of the switching power into the Mini USB port on back of the desktop charger. 3. Place the radio with the battery attached, or the battery alone, into the charger. 4. Make sure that the battery is in good contact with charging pieces of the desktop charger. The charging process begins when the charger LED glows orange.
图2:六联排充充电示意图 Figure 1 Schematic Diagram of Six-Unit Charger When multiple desktop chargers are used simultaneously, you may connect the chargers in parallel to create a multi-unit charger. Assembly Method: Slide the latch of a charger into the slot on the bottom of another charger, as shown in Figure 2. 座充连接扣 Latch of Desktop Charger Figure 2 Diagram of Multi-Unit Charger Assembly Antenna Information z Stubby antenna is durable and ideal for communication at low transmit power.
days or forest locations may narrow your communication range, so please make full preparations in advance to avoid potential inconvenience. Assembly and Disassembly Attaching/Removing the Battery Attaching the Battery 1. Press the belt clip down (in direction of ①) to make its bottom up. Then push the battery (in direction of ②) into the radio. See Figure 1. Note: Make sure the battery tab is fully inserted into the radio’s slot. 1 2 Figure 1 2.
Figure 2 Removing the Battery 1. Make sure the radio is powered off first. Press the belt clip down (in direction of ①) to make its bottom up. Then lift the battery latch (in direction of ②). See Figure 3. 1 2 Figure 3 2. When the battery bottom gets tilted, release the latch and remove the battery (in direction of ③) as shown in Figure 4.
Attaching/Removing the Antenna Attaching the Antenna 1. Align the threaded end of the antenna with the antenna connector located on the radio’s top side. 2. And turn the antenna clockwise to fasten it. See Figure 5. Figure 5 Removing the Antenna Turn the antenna counter-clockwise until you can remove it.
Figure 6 Removing the Belt Clip Use a screwdriver to loosen the screws and remove the belt clip. Note: Please be careful to avoid missing of screws. Attaching/Removing the External Earpiece/Mini USB Device Attaching the External Earpiece Loosen the strap (①), and tie it to the strap hole (②). Uncover the accessory jack cover (③), and insert the earpiece plug into the jack (④). Then rotate the other end of the strap into the connector of the earpiece cable (⑤).
Note: When the earpiece is not in use, make sure the accessory jack is properly covered to prevent intrusion of dusts. Attaching the External Mini USB Device Uncover (not remove) the Accessory Cover (in direction of ①), and insert the Mini USB connector into the Mini USB port (in direction of ②). See Figure 8. 1 2 Figure 8 Removing the Mini USB Device Pull the Mini USB connector out and remove it.
Adjusting the Volume Press [+] to increase or [-] to decrease the volume level. During volume adjustment, the radio will sound alert tones at your selected volume level. Selecting a Channel Rotate the Channel Selector Knob to align the channel numbers. Transmitting Press and hold down the PTT key, and speak into the microphone at your normal voice level. Hold the radio about 2.5 to 5 centimeters away from your mouth. Receiving Release the PTT key to receive.
switch even if you rotate the Channel Selector Knob, and this feature always remains valid after PC programming.) Advanced Operations The following functions are programmable by your dealer. CTCSS/CDCSS You may set up talkgroups with unique CDCSS/CTCSS to prevent unwanted conversations at the same frequency. If CTCSS/CDCSS is set on the current channel, CTCSS/CDCSS match is required for the radio to unmute to an incoming signal.
beeping until the PTT key is released. Your dealer can program a pre-alert function to warn you of the TOT expiration in advance. Battery Strength Indicator When you intend to know the battery strength, press the programmed Battery Strength Indication key to illuminate the Status Indicator and learn the battery strength by different colors. To exit this function, release the key. Status Indicator of different colors represents different battery strength levels.
Operation: Press the Squelch Off key to enter this mode, and press it again to exit. z Squelch Off Momentary Purpose: Refer to Squelch Off. Operation: Hold down the Squelch Off Momentary key continuously to enter this mode, and release the key to exit. z Monitor Purpose: In this mode, the receiving party can receive incoming calls from the transmitting party regardless of CTCSS/CDCSS condition. If the carrier condition is not satisfied, the receiving party will fail to receive any incoming calls.
Figure 1 Normal Scan Sequence Priority Channel Scan Suppose there is a scan list of 5 channels and Channel 2 is prioritized as Priority 1, the scan operation may proceed in the following sequence, as shown in Figure 2. Figure 2 Priority Scan Sequence z Scan On/Off You can enter Scan mode through any of the following two methods: Key-operated Entry Press the programmed Scan key to enter Scan mode, provided that there are no less than 2 channels in the scan list.
channel; when the radio is not staying on a scanned channel, it transmits on a preset channel. Unchecked: The radio transmits on the preset channel. z Priority Scan This function enables users to scan the most frequently used channel so that messages will not be missed. The priority channels are programmed by your dealer via programming software. Please contact your local dealer for more information.
2. Plug the earpiece into the accessory jack of the radio. 3. Press the programmed VOX key to activate the VOX feature. 4. Speak through the microphone on the earpiece to transmit your voice. Operation Instructions: 1. Press the PTT key on you radio to disable the VOX during its operation, and release the key to reactivate this function. 2. Press the programmed VOX key to enable/disable the VOX feature, with corresponding alert tone.
to perform auto-detection until it operates normally. During the detection process, do not handle the earpiece; otherwise, it may malfunction due to detection errors. 3. If the earpiece functions abnormally, please pull and plug it again as instructed above. 4. You may select VOX levels according to the operating environment. Too much noise and too high VOX level may cause the radio to transmit continuously. 5.
z Group members may be too far away from each other. Please make sure that you are within the communication range. z Hear non-group members. The CTCSS/CDCSS settings should be changed for all radios in your group by your dealer. z selected. No voice or low voice received from the transmitting party. Please ensure an adequate volume level is z Or please send the radio to your dealer for microphone examination. z In Monitor mode, group members may have been too far away from each other.
Earbud with In-Line PTT Earset with In-Line MIC & Li-Ion Battery (1700mAh) Six-unit Switching Power ESS09 VOX EHS09 BL1716 PS4001 Rapid-Rate Charger Vehicle Power Adapter Remote Ring PTT Switch Wrist Strap (Nylon) (for Li-Ion Battery) CH06L01 PV1001 POA18 NCN004 Note: Pictures above are for reference only and may vary from actual product. However, featuring functions shall be held.