® Ages 14+ READ THE INSTRUCTION MANUAL CAREFULLY PLEASE VISIT WWW.HUBSAN.
Hubsan FPV X4 Desire V1.0 2016.03 Please read the instruction manual carefully! CAUTION: For safety, the quadcopter is default set to CAN NOT FLY WHEN NO GPS. If you prefer to fly when GPS is not available, please reset the value as instructed below before using. Pull the throttle stick to the lowest position and press the Elevator stick for 1.5 seconds to enter into the MAIN MENU interface.
INTRODUCTION Thank you for buying the HUBSAN product. It is designed as an easy-to-use, multi-functional RC model, capable of hovering and acrobatic flight maneuvers. Please read the manual carefully and follow all the instructions. Be sure to keep the manual for future reference. Quadcopter Weight: 155g(including battery) FPV: First Person View Function enables you to experience every live moment of the flight from the drone's point of view. 1.
2. QUAD COPTER MOTOR LED INDICATOR Indicator Status: Front LED: is blue; Back LED: is red. 1. Power on: 4 LED indicators blink simultaneously every 1.5 seconds. 2. Compass Calibration: 1). Horizontal calibration: 4 LED indicators blink circularly. 2). Vertical calibration: 4 LED indicators blink alternately. 3. GPS Flight: 4 LED indicators remain lighted. 4. GPS Return : 2 front LED remain lighted, and 2 back LED blink twice every second. 5.
4. PROPELLERS Attach the propellers to the corresponding motors that are marked A and B,tighten the propellers and keep the motors deadlocked with the screw-driver. “I” Mark “D”Gap Match the “I” mark on propellers to the “D” gap on motor shafts when assembling, as figure 1 shows. ● Make sure that the A and B propellers are installed correctly. The X4 will not fly if propellers are improperly installed. ● Hazardous moving parts keep fingers and other body part away.
5. START TO FLY 5.1 FLIGHT ENVIRONMENT (1) The flying area should be open and without tall buildings or other obstacles; the steel structure within buildings interferes with the compass and the GPS signal. (2) DO NOT fly in bad weather such as strong wind, heavy snow, rain or fog. (3) Keep away from barriers, people, power cables, trees, and other obstructions. (4) Do NOT fly near radio towers or airports. (5) The X4 control system will not work properly at the South or North Pole.
5.4 BASIC FLIGHT The operation mode for the transmitter including Mode 1 or Mode 2. The manual will use Mode 2 as an example to illustrate the transmitter’s operation. Transmitter (Model 2) X4 Remarks UP The throttle stick controls the ascent and descent . Push up the stick and the X4 will ascend. Pull down the stick and the X4 will descend. When the stick is in the center, the X4 will hover and hold its alititude automatically . Move the throttle stick above the center position to take off.
The GPS Switch controls the position-hold function. position 1 (upward) In position 1 (up), the GPS function works. position 2 (downward) In position 2 (down), the GPS function is inactive. GPS Switch Photo Button RTH Switch The RTH Switch controls the automatic return home function. Video Button In position 1 (up), the RTH function works. In position 2 (down), the RTH function is inactive. Important Note: The GPS and RTH functions are only available outdoors.
6. ADVANCED PERFORMANCE SETUP 6.1 GPS POSITIONING/ HOME POINT SETTING 1.) GPS Positioning works ONLY when the GPS signal has no less than 6 satellites. 00:23:59 7.3V R 0 P 0 H 247 0.3m/s 1.5m 0m 00:23:59 7.3V 00:00:00 S: 0.1m/s 7.3V R 0 P 0 H 247 H: 0.0m D: 0.0m GPS 6 N22.7914931 E:114.0479740 GPS 6 N:22.7914650 E:114.0479983 Altitute GPS 6 N22.7914931 E:114.0479740 GPS 6 N:22.7914650 E:114.0479983 Altitude Push up the GPS switch to activate the GPS positioning.
EXIT RTH MODE Pull down the RTH Switch, the X4 will exit the RTH Mode. 6.3 HEADLESS MODE Headless mode means the X4 will default any directions (corresponding to the directions of transmitter sticks) as the up ahead when the mode is activated. MODE 2 MODE 1 Press the Throttle stick 0.5 second to switch on/ off headless mode. Press the stick to enter into Headless Mode, indicated by two "beep" sounds and the “Headless On” displays on the LCD.
Press the Elevator stick for 0.5 second to switch on/ off follow me mode. Press the stick to enter into the follow me Mode, indicated by two "beep" sounds, the “ Follow On” displays on the LCD and the drone will turn and face the transmitter. Press the stick again to exit follow me Mode, indicated by one "beep" sound and the “ Follow Off” displays on the LCD . ! The follow me mode only works when the GPS (both on transmitter and on drone) has no less than 6 satellites.
7. TRANSMITTER Quad copter’s battery capacity Recording time Transmitter’s Record/Camera SD Card battery capacity status 00:23:59 Voltage Tilt Angle Pitch Angle Nose Orientation 0.3m/s 1.5m 0m 7.3V R 0 P 0 H 247 GPS Signal Quad copter’s GPS Transmitter’s GPS GPS 6 N22.7914931 E:114.0479740 GPS 6 N:22.7914650 E:114.
7.1 INPUT KEY FUNCTION S/N (1) (2) Mode/ Control MODE 1 Throttle/Aileron Stick Push the stick forward or backward and the quadcopter will ascend or decend; Push the stick left or right and the quadcopter will fly left or right. Push the stick forward or backward and the quadcopter will fly Elevator/Rudder Stick forward or backward;Push the stick left or right and the quadcopter will rotate counter clockwise or clockwise.
7.2 INSTALL THE TX BATTERY PUSH PUSH Remove the cover Install 4 x AA batteries according to the correct polarities ● Do not mix old and new batteries ● Do not charge non-rechargeable battery. Close the cover ● Do not mix different types of batteries 7.3 REVERSING CHANNEL SETUP If you would like to reverse any of the stick functions due to personal preference then follow the instructions below. Be aware that it will change the controls back to front.
0:08:49 M2 0:08:49 MAIN MENU Set Reverse Set Sensitivity 5.8G Frequency Set Manual Fly When no GPS Show Version Exit M2 SET SENSITIVE Exit Expert mode 100 Elevator : 100 Aileron : 100 Rudder : Sensitivity default setting is in Expert Mode. The quadcopter can’t be disarmed when sensitivity value less than “60”. 7.
8. COMPASS CALIBRATION Compass calibration is required before the first time flight, otherwise the system may not work properly. The compass is very sensitive to electromagnetic interference which can cause abnormal compass data and lead to poor flight performance or even flight failure. Regular calibration enables the compass is in optimum performance.
9. TRANSMITTER CALIBRATION Mode 2: Push both sticks to the upper left corner and power on the transmitter simultaneously,rotate both sticks in circles twice, then press any trim for 1.5 seconds until the LED on the transmitter turns solid green which indicates a successful calibration. Mode 1: Push the left stick to the upper left corner and the right stick to the upper right corner and power on the transmitter simultaneously, rotate both sticks in circles twice, then press any trim for 1.
EXPLODED VIEW 18 ©2016 Hubsan 哈博森科技 版权所有
NO PART NAME 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 19 Lower Body Shell 5.8 GHz Transmission Module Main Control Board Compass Module GPS Module Blue LED Red LED Camera Module Motor A Motor B Li-Po Battery 5.8G Attenna 2.
Ｈ５０２Ｓ Ｓ ＰＡ ＲＥ ＰＡ ＲＴ ＣＨＡ ＲＴ H502S-01 Body Shell Set H502-01 H502-02 H502S-02 Battery Cover Eye Lampshade Lens Holder H502-03 H502-04 Lamp Base A/B Screw Set H502S-03 H502-05 H502-06 H502-07 H502-08 H502-09 Propeller A/B Motor A Motor B Motor Holder Bearing Motor Gear A H502S-06 H502-14 H502-10 H502-11 H502-12 H502-13 Motor Gear B Motor Shaft LED Kit 2.
ＦＣＣ ＩＮＦＯＲＭＡ ＴＩＯＮ This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
User manual is subject to change without prior notice due to unforseen product upgrades. Download the latest user manual from WWW.HUBSAN.COM VERSION 1.
ＦＣＣ ＩＮＦＯＲＭＡ ＴＩＯＮ This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
