NANO Q4 CAM PLUS NO.
Content Introduction------------------------------------------------ 1 Safety Notes------------------------------------------------- 1 Safety check before flying------------------------------ --- 3 Charge the Li-Po battery-------------------------------------- 3 Remote Controller------------------------------------------ 5 Camera------------------------------------------------------ 6 Start to Fly-------------------------------------------------- 7 Advanced Performance Setup------------------
1 Introduction Thank you for buying the HUBSAN products. It is designed as an easy-to-use, multi-functional RC model, capable of hovering, fast forward and acrobatic flight maneuvers. Please read the manual carefully and follow all the instructions. Be sure to keep the manual for future reference. 2 Safety Notes 2.1 Important Notes This multi-functional RC model is not a toy. In case of any injuries caused by improper operations, please read the instructions carefully before use.
2
2.4 Prevent Moisture The quadcopter contains many precision electrical componets. Store the battery and the quadcopter in a dry area at room temperature. Exposure to water or moisture may cause malfunction resulting in loss of control. 2.5 Proper Operation For safety, pnly use Hubsan spare parts for replacement. 2.6 Always Be Aware of the Rotating Propellers Be careful to keep your body away from the working propellers. Always keep the quadcopter fly in sight.
4.2 Power-on/off Long press the power button to turn on/off the quad.
5.1 Input Key Functio S/N Mode/ Control Function Mode 2 Push the stick forward or backward and the quadcopter will ascend or decend; Push thestick left or right and the quadcopter will rotate left or right. 2 Mode 2 Elevator/ Aileron Stick Push the stick forward or backward and the quadcopter will flyforward or backward;Push the stick left or right and the quadcopter will fly left or right.
Calibrating Procedures: Mode 2: Push the left stick to the most right corner, and move the right stick left to right quickly, the 4 LED indicators on quadcopter will blink alternately, calibrationsucceeded when the indicators stop blinking. Mode 1: Push the left stick to the most right corner, put the right stick to the lowest and move left to right quickly, the 4 LED indicators on quadcopter will blink alternately, calibration succeeded when the indicators stop blinking. Mode 2 Mode 1 6 Camera 6.
7 Start to Fly 7.1 Power-On The quadcopter is designed with Power-On safety system, it ensures the motors will not start undelss safety signals detected. 7.1.1Turn on/off the remote controller by pushing power switch to left/right. Make sure the Throttle stick is in the full down position, power on the remote controller, then quadcopter. Do not push any sticks or trims before pairing is succeeded, or the quadcopter will drift. 7.
Right Rotation Mode 2 Mode 1 Left Rotation The Rudder stick controls the rotate direction Push the stick to the left and the X4 will rotate left Push the stick to the right and the X4 will rotate right Pushing harder will cause the X4 to rotate faster in the corresponding directions. Mode 2 Forward Mode 1 Backward The Elevator stick moves the X4 forward and backward. Push the stick up the and the X4 will fly forward. Pull the stick down and the X4 will fly backward.
7.3 Headless Mode Headless Mode means the quadcopter default any directions (corresponding to the directions of transmitter sticks) asits up head when the mode is activated. 2 front LED blink simultaneously when in Headless Mode. Mode 2 Mode 1 Short press the Throttle stick for to enter/exit headless mode. Short press the Throttle stick to enter into the headless mode, indicated by two“Beeps”. Short press the Throttle stick again to exit the headless mode, indicated by one“Beep”.
9.2 Backward Flip Push the Elevator stick backward quickly. Release the stick to the center after flip. Mode 2 Mode 1 9.3 Left Flip Push the Aileron stick to the left quickly. Release the stick to the center after flip. Mode 2 Mode 1 9.3 Right Flip Push the Aileron stick to the right quickly. Release the stick to the center after flip. Mode 2 Mode 1 Flip Mode is not available when battery is low.
10 Propellers A B A=A B A (1) Attach the propellers to the corresponding motors that are marked A and B; B=B (2) Tighten the propellers to the motor shaft. ● Make sure that the A and B propellers are installed correctly. The quadcopter will not fly if propellers are improperly installed.
Exploded View 1 2 2 1 5 4 3 6 8 7 9 10 S/N Part Name Qty S/N 1 Propeller A 2 6 Li-Po Battery 1 2 Propeller B 2 7 PCBA 1 3 0614 Motor A 2 8 Camera 1 4 0614 Motor B 2 9 Lower Body Shell 1 5 Upper Body Shell 1 10 Screw 4 12 Part Name Qty
H002 TRROUBLESHOOTING 1. Transmitter and Quadcopter can not pair Throttle position needs to be fully down. Please do not move any sticks or trims during initial power-on binding. 2. Gyro not Working Well 1）Battery voltage is too low； 2）Re-bind； 3）Land the quadcopter on the ground with the throttle stick fully down, take off again after 3 seconds. 3. Unable to Flip Li-Po power is too low, re-charge the battery. 4.
Mode 2 Mode 1 8.The camera can’t record 1）The SD card can’t be read by the quad. Please use MicroSD card (2-16GB, Class 4, UHS-1), Do not use any privated MicroSD. 2）Replace camera module 3）Format Micro-SD in the computer H002 Spare Part List H002-01 Body Shell Set H002-02 Screw H002-07 Propeller A/B H002-03 Motor A/B H002-04 2.
FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
