DR-9200 SHENZHEN HQT SCIENCE & TECHNOLOGY CO ., LTD . For more information, please visit www.hqtsolutions.com All rights reserved to HQT. Pictures shown in this manual are for your reference only, if there is fluctuation, please take the material object as the standard.
Statement HQT endeavors to achieve the accuracy and completeness of this manual. As for any inaccuracies and omissions that may possibly occur, the right to interpret is reserved to Shenzhen HQT Science & Technology Co., Ltd. Hello Thank you for purchasing HQT DMR digital repeater DR-9200.
HQT On-line Service Center More Professional Technical Support User Manual and Brochures HQT service network provides more information about To provide downloading or on-line reading of the latest user manuals and brochures in covering on-line service of HQT two-way radio. detailed information of two-way radios. More detailed product information To deepen your understanding of the functions of this radio. Software Download To provide downloading of the latest programming software from HQT website.
Safety Information Please read the following safety guidelines. Nonobservance of these guidelines may cause danger or violation of law. Warning Warning Warning Don’t transmit with antenna detached from the radio or don’t damage or change antenna type. Strong electronic waves are emitted from the radio and damages or changes to the antenna may effect the performance of the radio, and it may cause the radio to be defective and not covered under warranty. Don’t use other manufacturers’ accessories.
1.RF Radiation Information This product must be restricted to operations in an Occupational/Controlled RF exposure Environment. Users must be fully aware of the hazards of the exposure and who are able to exercise control over their RF exposure to qualify for the higher exposure limits. FCC Regulations Federal Communication Commission(FCC)requires that all radio communication products should meet the requirements set forth in the above standards before the can be marketed in the U.
Contents Safety Matters ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 03 Repeater Overview ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 11 ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 04 Front Panel ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 11 Product Inspection General Installation ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 05 Pre-Installation Overview 05 Environmental Conditions at Intended Installation Site 06 Ventilation Requirements 07 AC Input Power Requirements ‐ 07 Mounting Methods 08 Grounding and Lightning Protection 08
Safety Matters Product Inspection Please read the rules below. Nonobservance of these rules may cause danger or violation of law. • The use of this radio must comply with regulations of local government. Please unpack carefully and check that all items listed below are received. If any item • Turn off the radio before you enter places of potentially explosive or flammable environment. is missing or damaged, please contact your dealer.
General Installation • Configure parameters (e.g. Working Frequency, PL, Code, Color Code etc.) of the repeater based on user's requirements Proper installation can ensure optimum performance and reliability of the HQT repeater and, therefore, pre-installation planning is required. This includes considering the mounting location of the equipment Environmental Conditions at Intended Installation Site in relation to input power and antenna.
the dirt or dust in the internal PCB and module is difficult to clean, and may cause problems such the power supply to AC power supply. as superheating and discontinuously electrical connection etc. A grounding socket-outlet with standard 3-core cable is recommended to connect the AC power supply. Ventilation Requirements The socket-outlet must be connected to the AC power supply which can provide a maximum power The repeater is equipped with a cooling fan to provide forced convection cooling.
• Electrical Grounding Ground cable used for transmitting the current from site circuit or devices belongs to Electrical Mechanical Installation Grounding. It includes the AC or DC power supply used for site power device, and lines or cables This section introduces mechanical installation steps of HQT repeater. Various mounting methods for connecting site alarm or sensor. vary depending on different types of rack or cabinet selected for fixing the repeater.
Repeater Overview NO. Item Description 1 Tx Connector N Type (Roll Pass) 2 Ground Screw Must be connected to system grounding. 3 Main Fan 4 Ethernet Connector 100Base-TX (RJ45) 5 Rear Accessory Connector For plugging programming cable. 6 Rx Connector BNC (Roll Pass) 7 Power Fan Continuously working to cool the repeater. Change speed. Stops at room temperature. LED Indicators LED Front Panel works for a long time.
Optional Accessories Rear Accessory Connectors The main optional accessories of the repeater are listed below. For more information, please contact your dealer or HQT. Pin No. Pin Name Pin Function 1 USB_VBUS USB External Power Supply 2 GND 3 MAP_GPIO_3 4 5 6 GND 7 EXT_MIC+ External MIC/Audio Input Connector 8 RX_AUDIO RX Audio External Output Connector Pin No.
Troubleshooting Care and Cleaning Phenomena Analysis Solution The repeater can not a. Power cord is not connected or is not securely connected to the outlet. b. Power cord fuse is damaged. a. Properly connect the power cord and ensure secure connection. b. Check if the DC fuse has blown, and if yes, replace it with a new one. be powered on. a. TX/RX f requency of the repeater is inconsistent Group members can not talk to each other, or the repeater can not communicate with a subscriber radio.
Service and Support Shenzhen HQT Science & Technology Co., Ltd. (“HQT”) provides long-term support for its products, including repair and supply of the radio and its parts and accessories. Service Commitment 1. HQT two-way radio body has an 18-month warranty; accessories (battery, adapter, charger and antenna) 6 months; earphone 3 months. 2.
FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.