User Guide iOS Android
1. Wiring Diagram............................................................................................................. 2. System requirement................................................................................................. 1 2 3. Application installation............................................................................................ 2 4. WiFi settings................................................................................................................. 2 5.
1 Wiring Diagram WACL CACN V+ CCT Panel HLD503-Z-CT ACL C- ACN V+ Panel HLD503-Z-SC 1
2 System requirement Android2.3 and above iOS 6.0 and above 3 Application installation Scan QRCode, and install application. 4 WiFi settings Power on the gateway. Please select the WLAN iLightsInxxxxxx on mobile settings menu. The xxxxxx is the mac address on back of gateway. Connect the WiFi AP, and open installed application(Picture1,2). Attention : The gateway can be set to connect another router on application setting menu. See chapter 8.2 Network settings.
Picture1 Picture2 Picture3 6 Add device Enter Settings menu/ Add device with 2 methods to add device(picture3,4). a) Add device by QRCode scanning. Each of device has one QRCode. Usercan scan QRCode to add device in application(Picture5).Save the scanned device and check it by Testing button(Picture6).
Picture4 Picture5 Picture6 Attention: The device and gateway has to be power on while test button is pressed, but the device can be power off while scanning QRcode to add device. And the gateway has to be power on when enter Add device or Add group menu. b) Add device by pairing. The following are steps to add device by pairing mode 1.First input the device name and select correct device type.
2.Activate the device pairing mode by power on device (some device will be on pairing mode in 5 seconds after power on). Or user also can activate pairing mode by press the key of device. 3.Save the device while device is on pairing mode (The pairing command will be sent to device while save button is pressed)(Picture7, 8). Attention: a. The device type on Add device menu has to be thesame with device! b. The following is the definition to activate pairing mode for different device.
Picture7 Picture8 Picture9 The lights have to bound with daylight sensor for daylight sensor control. The following is the operation steps.(Picture12,13) Attention: Please binding the device before control the daylight sensor.See chapter 8.3 Binding settings. a).Power on lights. Bind the light or group in Settings/Binding settings menu. b).Change the lights brightness to favorite luminance(User can use illuminometer to get favorite luminance).
c).Find the sensor in Area/All devices menu. d).Power on sensor. Go to sensor parameter menu. Set current Lux as constant value. Attention: The stored lux value is around sensor! Turn on the senor in App. Then sensor will change all bound lights brightness based on environment luminance. (If user needs to change the sensor parameter, please turn off sensor in APP first. Then turn on sensor after parameter setting.
Picture13 The part Click Picture14 Picture15 can set different effect, interval and run or stop. to enter Timer or delay menu. Under this menu, user can set the timer or delay and different status while timeout (Picture14,15,16). User can store the power on color for Color temperature light(Picture17). User select different type device by the following icons (Picture18).
Picture16 Picture17 Picture18 7.1 Edit area User can long press the area button on area menu to edit area or delete area (Picture19). 8 Settings Click to enter settings menu.
Picture19 Picture20 Picture21 8.1 Import data/Export data All devices , scene and area are stored on client as database. Please back up your database after all devices, scene and area adding done. Apps support database synchronization between 2 clients(Picture20,21,22). a. Import or export database from SD card or to SD card. (Android) b.
c. Import or export database from gateway. 8.2 Network settings The gateway also can join another WiFi router for remote control. Attention: The gateway will recover the default settings after the setting is failed with wrong SSID, encryption type or password.
8.3 Binding settings(Picture23,24,25,26,27) a).Open Add devcie, select Add by QRcode, Scan the QRcode back of touch dimmer. b).Input name and save. Then the touch dimmer has to bound with lights before light control. Handheld dimmer has to press any key before Click Save. d).User can bind the remote control, handheld dimmer and sensor with lights.
9 Environment and Electrical parameters Parameters HLD503-Z-CT Input power 100-277VAC Channels Output Current 2 Channels 1 Channel 950mA MAX 950mA MAX Output DC 24-38V 24-38V PF > 0.9 > 0.9 EFFICIENCY Wireless frequency Max 85% Max 85% 2.4GHz 2.4GHz Operation temperature -20℃ to 55℃ -20℃ to 55℃ No land power < 0.5W < 0.5W HLD503-Z-SC 100-277VAC This device complies with part 15 of the FCC Rules.
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.