HOLATEK – A3 User Manual 3D LED Smart Projector & TV
Contents SAFETY INSTRUCTIONS ................................................................................................. 4 THE SAFETY SIGNS ........................................................................................................... 4 NOTICE FOR USE ............................................................................................................... 4 BATTERY INSTRUCTION ..................................................................................................
Safety Instructions Thank you for purchasing the HOLATEK Projector. You need to read carefully the “safety instructions” before using it. After reading the User Manual, please keep it for future reference. The safety signs To ensure the safety of you and others and keep the items from damages, the User Manual applies a variety of signs whose meanings are as follows: This sign indicates that ignoring the sign and wrong operations will lead to death or serious injury.
2. Unplug the power plug of the machine; 3. Contact your dealer or the HOLATEK authorized service center. ● Fault Please immediately stop using the machine (continuing using it will lead to dangers of causing fire and electric shock) if the picture display is abnormal or has any other abnormal phenomenon under correct operations, and please take the following measures: 1. Turn off the power of the machine; 2. Unplug the power plug of the machine; 3.
When using this machine in the in the country where it is purchased, please use the attached power cord; when using this machine in other countries, you must purchase and use a power cord which meets the national power supply requirements and pay attention to the safety standards of that country.
● Drop and impact Continuous use may lead to dangers of causing fire and electric shock if the machine is damaged due to drop or other reasons. In this case, please immediately take the following measures: 1. Turn off the power of the machine; 2. Unplug the power plug of the machine; 3. Contact your dealer or the HOLATEK authorized service center. ● Incineration Do not discard the machine by incineration, or it will lead to dangers of explosion, fire and personal injury.
Do not erect the machine during the operation ● Lightning Do not touch the power plug of the machine when thunderstorm and lightning occur ● Remote control Do not dismantle or reconstruct the remote control in any way as it may lead to dangers of electric shock, burn and other personal injury. All internal inspections, debugging and maintenance must be entrusted to your dealer or the HOLATEK authorized service center Do not wet the remote control.
If you are using a cardiac pacemaker or any other electronic medical devices, please consult doctors or the manufacturers of such devices before operating the product.
● Refraction effect There shall be no fishbowl or other items which may produce refraction effect in front of the machine when the light source unit is lit as it may lead to dangers of causing fire ● Lens Do not touch the lens with hands ● Clean The dirty machine inner with accumulated dusts may result in dangers of causing fire and breakdowns; Please contact the dealer or the HOLATEK authorized service center once per year to have the machine’s internal cleaned.
Make sure the batteries are in the correct direction when inserting them; Batteries specified by remote control only ● Depleted batteries Depleted batteries must be removed from the remote control as soon as possible; Remove the batteries if the remote control will not be used for an extended period of time ● Batteries disposal Dispose the used batteries according the local laws and regulations Operation Instructions The light source Light source unit of the machine applies LED The
Other Instrustions This machine is composed of precision parts and failure to comply with the following instructions may result in failure to correctly save data and risk of breakdowns: Do not operate or place the projector in any of the following environments as it may lead to breakdowns and damage to the machine Locations which generate static electricity easily; Locations with excessive temperature; Locations with excessive humidity; Locations where the temperature may change suddenly;
● Clean with a soft dry cloth The projector is dirty; please clean it with a soft dry cloth soaked in the water and neutral detergent diluents. Wring the cloth till dry before wiping; diluents, benzene and any other volatile chemical are not allowed to clean the projector, otherwise the printing would be wiped and dirty the projector.
summary Packing list ● Carefully open the package and check whether the projector includes the following items: Packing list Graphic Amount HOLATEK-A3 intelligent projector *1 Remote controller *1 AC power cord *1 USB line *1 14
User manual *1 Warranty card *1 Note: if any missing items or damage or device does not work, please contact the distributor immediately. System upgrade ● Android software upgrade process is as follows: 1. First of all, you need a Windows PC with access to the internet; 2. Download the firmware upgrade software in the official website; 3. Install the firmware upgrade software in PC; 4. Download the firmware upgrade package in the official website; 5.
The location and function of control External view Corresponding Definition instruction number Air Inlet Air Inlet Controlling Controlling(detailed in “control area”) LED LENS LED LENS IR Receiver IR Receiver Air Outlet Air Outlet Indicator Indicator (see details in P30 “Indicator”) 16
Control area Corresponding Definition instruction number Menu Menu Power Power Source Source Down ↓ 3D 3D Enter OK W-T W-T(W stands for the wide section in zoom lens, T stands for the long period) 17
DLP Esc DLP Esc Volume+ Volume+ Up ↑ Volume- Volume- Rear view Corresponding number Definition instruction Update Update TF-card slot *2 USB2.
AC power line interface RJ-45 network interface OTG-USB interface HDMI interface (input) AV interface (input) Bottom view Corresponding number Definition instruction Front floor mat *2 Rotate, rise and adjust projection angle Rear floor mat *2 Anti-skidding Positioning hole *4 For installing hanger/bracket 19
Function of remote control Corresponding Definition instruction number Menu Menu Key response Key response Power Power 20
Left ← Enter OK Mute Mute DLP Menu DLP Menu Volume+ Volume+ Volume- Volume- 3D L/R 3D L/R Local input Local input Reserve (Red) Reserve (Red) Reserve (Green) Reserve (Green) Home Home Back Back Up ↑ Right → Down ↓ DLP Esc DLP Esc Keystone+ Keystone correction+ 3D 3D Keystone- Keystone- AV input AV input HDMI input HDMI input Reserve (White) Reserve (White) 21
Reserve (Blue) Reserve (Blue) ● Effective range of remote control With infrared (IR) remote sensor in the front of the projector; The remote control must remain orthogonal angle of 30 degrees with the infrared remote control sensor, so that it will function normally; The distance between the remote controller and sensor is no more than 8 m (about 26 feet); No obstacle blocks off the infrared beam between remote control and infrared sensor on the projector.
screen and wall, the size of the projection image will grow accordingly; Refer to the following table when installing the projector, so that the optimal size images are projected onto the screen. Screen The lens center Projection screen size This is the height from the lens center to projected image’s bottom. (A: When the lens is displaced at the highest position ) Projection distance Unit :cm ● Projection distance Unit:m Screen 40 80 100 150 200 250 300 1.2 2.3 2.9 4.4 5.9 7.3 8.
Methods of projection Caution ● If the projector is installed in the ceiling, it shall be installed by qualified technical personnel with approved installation equipment. If not installed correctly, the projector may fall, thus leading to personal injury or accident. Please contact your dealer to properly install this projector.
Don’t touch the vents and the air outlet which would be extremely hot when the projector is being used; Avoid placing plastic products or other heat sensitive items next to or below the projector to avoid the risk of deformation and discoloration; Avoid placing the projector on the unstable and vibrating surface; Avoid placing the projector on carpets, blankets, towels and other soft goods; Avoid placing the projector in the places with direct sunlight; Avoid placing the projector in
shorten the lifespan of the light source unit; The air discharged from the air conditioner will blow the heat discharged from the projector lens, causing the heat wave in projection. If this case happens, please adjust the air from the air conditioner or move the projector; Please place the projector in a horizontal position. Don’t tilt or place the projector sideways when using, or it may cause malfunction.
Basic Operations Turn on and turn off the projector ● Notice for AC power Use AC power cord attached with the projector; Use AC power whose output voltage accords with the rated voltage of the projector; Don't share a power supply socket with other devices; If using extension line, make sure the rated current of the extension line is adapted for the power of the projector; Don’t use bundled power cord; Don’t place articles on the power cord or step on it; Don’t pull the power cord
1. Connect the projector and the power socket with attached AC power cord; 2. When power cord is inserted into the power socket, the power button at the top of the projector will become orange, which means the projector is powered on and bootable. ● Turn on the projector 1. Press the (power) button on the top of the projector or on the remote controller to turn on the projector, and then the color of the (power) button will change from orange to blue; 2.
goes out, and then unplug the AC power cord from the outlet. Option of information language When the projector is turned on for the first time, the default language is Chinese. If you need to change the language, you will be subjected to the following steps (the operating steps of projector and remote control are consistent): 1. Press “Menu” button; 2. Press“▲” or “▲” button to select the “Machine setting 1”, and then press “Menu” button; 3. Select your desired language and press “Menu” button to confirm.
● Operation on the remote control: Press “Keystone+” ( ) or “Keystone” ( ) buttons to correct the keystone. ● Operation on the projector: 1. Press “Menu” button; 2. Press “▲” or “▼” button, select the “Picture setting” and press “Enter” button; 3. Select the “keystone” and press the button of “ ” or “ ” to correct; 4. After the correction, press “Menu” button to exit the operation. Useage of 3D function ● Start the 3D function After starting the 3D film source, operate with a remote control.
If you feel discomfort or the picture is without a 3D effect, you can operate with a remote control. Press “3D L/R” button to adjust ● Close the 3D function Press “3D” button with a remote control, select “2D”, and then press “Enter” button to close 3D or 2D TO 3D function. Usage of setting options During the image projection, press “Menu” button and the setting options will be displayed on the screen. The setting options can be used to match various settings of projectors.
Ceiling projection Start picture Aspect ratio Blank picture Recovery menu defaults Signal name indicator Input setting Recovery menu defaults Eco mode Auto shutdown Machine setting 1 Language Recovery menu defaults Machine setting 2 Focusing Input signal Signal name Horizontal frequency Operation information Vertical frequency Scanning system Using hours of light Software version Fully recovery defaults Fully recovery defaults 32
Maintenance The unit of light source If the light source point is off, you must contact your dealer or HOLATEK Indicator Definition description Power adapter is plugged for starting up The projector is started and available Orange Power Blue Off Temperature of projector is normal Over-temperature Warning Red Temperature of abnormal and automatically Off Android system is not started Blue Android system is started and available Off Wireless network is out of service Blue Wireless network availab
Indicator Troubleshotting If there are any problems with the projector, please check the followings: ● Projector fails to boot up Cause Solution Plug one end of the AC power cord into the The power cord is not plugged power connector and the other end into an outlet ( if there is a switch, make sure it is on) ● No pictures Cause Solution Select the input signal correctly through Incorrectly select input signal “Source” button on the projector or on the remote control The projector doesn’t connect w
There is a barrier between remote Remove the barrier control and projector The remote control is too far away The distance from remote control to projector is from projector not exceeding 8 meters (26 feet) Attention! Please try the following operations and maybe the projector will return to normal: Pull out AC cord and wait for at least 10 minutes; Plug AC cord and turn on the power again.
HOLATEK-A3 3D LED Smart Projector & TV (LED portable projector, recreational projector, household projector) ● Optical parameter Projection technology Displayed chip Lightness Contract ratio Recommen ded resolution Resolution Maximum DLP Digital Light Procession Projection Technology of Texas Instrument of America 1000 Lumen 2500:1 2500:1 1280*720 1920*1080P Type of light resource LED LED power 30W Normal mode Eco mode LED life 20,000 hours 30,000 hours ● Projection parameter Methods of zooming
Computer compatibility 480i,480p,576i,576p,720p,1080i,1080p Video compatibility NTSC,PAL,SECAM Loudspeaker 2W(double loudspeakers)*2 ● Android parameter Android V4.2 CPU Dual-Core GPU Mali400MP2 *2 RAM 1GB DDR3 Hard disk 8GB ROM Audio function Multichannel high-fidelity audio Ethernet RJ-45 Support 802.11b/g/n Support 802.11b/g/n WLAN Bluetooth Bluetooth TM v4.
Remote control *1 Alternating current power line *1 USB line *1 User manual *1 Guarantee card *1 Enjoy nationwide quality assurance and the three guarantees service Warranty policy Term of Warranty quality 1 year information guarantee Service 400-662-0138 hotline Monday to Friday: 9:00-18:00 Company name: Holatek Science and Technology Development Co.
Warranty and copyright information ● Warranty HOLATEK warrants the product against any defects in material and workmanship under normal usage and storage. Proof of purchase date will be required with any warranty claim. In the event the product is found to be defective within the warranty period, HOLATEK will assume the obligation to replace any defective parts (labor cost included) for you.
FCC Information and Copyright This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.