Interactive Whiteboard User Manual Please retain this manual properly for future reference. This is the general manual for Interactive Whiteboard and there might be slight differences between the actual product and the descriptions.
Table of Contents ATTENTION ....................................................................................................... 2 SYSTEM REQUIREMENTS ............................................................................. 3 INTRODUCTION ............................................................................................... 4 HOW TO INSTALL ............................................................................................ 5 HOW TO INSTALL HARDWARE .................................
Attention z Do not expose this whiteboard to rain or moisture so as to reduce the risk of fire or electric shock. z Do not expose this whiteboard to fire, electric shock and long time direct sunlight. z This device is heavy with N.W. over 15 Kg. Use expansion bolts to fix the device to the wall. z When the projector and interactive whiteboard are used together, do not stare directly at the light from the projector. Especially the kids should be warned about this.
System Requirements Lowest Environmental Requirements˖ z CPU: 1.0GHz×86 z Memory: 512M Byte z Display Card: Support 256 or above z Hard Disk:1GByte z Screen Display Resolution˖800×600ǃ1024×768ǃ1280×1024 z USB1.1 Port Recommended˖ z CPU: 2.0GHz×86 z Memory: 2GB or above z Display Card: Support 256 or above z Hard Disk:2GByte z Screen Display Resolution˖1024×768ǃ1280×1024 z USB2.
Introduction This interactive whiteboard uses IR scan and sensor technology. Working seamlessly with a projector and computer, the Interactive whiteboard can become a large touch display. Any projected image in the whiteboard can be operated by pens or fingers directly. Thus, it provides an interactive presentation platform for the lecturers.
How to Install The following instructions have stated the installation for all series products from our company. The user can refer to corespondent instructions according to the products purchased. Please contact the local distributor for mor details. How to Install Hardware ˊWhiteboard installation for A series Iˊ 1. Firstly install the smart pen tray of the interactive whiteboard˖Insert the box underprop into the pen tray.
2. Drill 8 holes for expansion bolts on the wall according to your preference (shown as a). Install the wall-mount brackets and tighten bolts into each hole. Hang up the whiteboard with calibration hole D in four corners in the wall-mounting bolts (shown as b).
IIˊ ˊWhiteboard installation for B series 1ˊFirstly install the smart pen tray of the interactive whiteboard˖Lock the smart pen tray to the metal supporting plate with three M5 bolts. Shown as follow˖ 2ˊThere are wall-mount brackets A and B on the back of the whiteboard. Wall-mount brackets B should be screwed.
Install the fixing plate according to the space between wall-mounts brackets A˖ After hanging up the whiteboard, drill 2 holes for expansion bolts according to actual positions, and fix wall-mount brackets B into the wall. Shown as follow˖ IIIˊWhiteboard installation for C series The whiteboards in this series have ultra-thin frames. To install with traditional blackboards, you are recommended to have embedded installation.
Whiteboard Diagram Blackboard Black board Sliding Blackboard Interactive Whiteboard Interactive Whiteboard Blackboard Blackboard Embedded Installation Diagram 9
IVˊ ˊWhiteboard installation for D. E&F series 1. Firstly install the smart pen tray of the interactive whiteboard˖First, please insert the 4 pin pen cable into the pen box of smart pen tray. Insert the box under prop into the pen tray. The PCB in pen tray should be exactly in the outlet of the underprop and the pen tray joints should be exactly in the box underprop slot. Screw in two M3 screws from the bottom of the pen tray.
2ˊThere are 4 pieces of whiteboard wall-mount brackets in the accessory box as follow. Place them on the wall according to the position of the hooks on the back of whiteboard and fix them with expansion bolts. 3ˊHang the whiteboard onto wall-mount brackets and make sure the hooks on whiteboard catch the brackets.
(C) ˄D˅ 12
(E) (F) 13
Vˊ ˊInteractive System Building 1. Make sure the whiteboard is firmly fixed before building the interactive system. 2. Adjust the positions of the projector and whiteboard to make sure images are projected to writing area of the whiteboard in full screen. 3. One corner of the whiteboard is set with USB port(position of USB port will be varied in different models). Plug the USB cable into the USB port. The USB cable in the accessory box is designed for this whiteboard.
How to Install Software Before software installation, exit the anti-virus or virus protection softwares in your computer. The software installation instructions in this manual are based on Microsoft Windows 7 system. There is an installation disc in the accessory box. Insert the installation disc and you can see the instructions. You can open the disc by manual if you do not see. Follow the instructions and complete the installation of the whiteboard software.
Calibration To work normally, the strokes on the whiteboard should coincide with the actual ones so as to calibrate accurately. The following situations need a calibration. z The whiteboard is used for the first time. z The whiteboard softwares have been reinstalled or updated. z The position of the whiteboard or projector is changed. z The computer connected to the whiteboard is changed. z The computer's resolution ratio or refresh rate is changed.
Step 3˖Adjust the projection angle and make sure the projection area is within the whiteboard display area. Step 4˖Mouse click the whiteboard service program icon at the bottom right of the screen and you can see the following˖ Click "Calibration" and the whiteboard will be in calibration interface as follow˖ Step 5˖Vertically touch the centre of the flashing "ॱ" with the interactive whiteboard pen tip until the flashing "ॱ" move to the next calibration point and thus one point is calibrated.
interface and complete the calibration of other points thus the interactive whiteboard calibration is finished. Notes˖ z Calibration with a finger might lead to inaccurate calibration. Calibration with the pens will gain a better effect. z Wrong calibration may lead to whiteboard not working and this requires recalibration. z Pressing "ESC" during calibration can cancel the current calibration operation. z There are minor differences between the calibration interface of different version softwares.
How to Use the Whiteboard The whiteboard can be normally used after calibration finished. Common computer operations can be realized without opening the writing software. Left Click Clicking the whiteboard with a finger or pen has the same effect as mouse left click. Normally it is for selection or pointing. Double Click Double clicking the whiteboard with a finger or pen has the same effect as mouse double click.
Roaming Spread your palm and press the whiteboard with five fingers at the same time and slide then you can have the roaming function. Tools and Resources The whiteboard with writing software running can realize more functions. You can refer to the writing software user manual for more details. Notes˖ z When you are roaming with your palm, you need to have five fingers pressing the whiteboard at the same time. Your fingers will be recognized as being writing if they are not pressing at the same time.
How to Use the Smart Pen Tray The smart pen tray can contain three whiteboard pens and one eraser. The slots on the pen tray from left to right are for red pen, black pen, blue pen and eraser. And all of them have priority properties: The eraser has the top priority, then blue pen, black pen and lastly the red pen. When you pick up a pen from the pen tray and write on whiteboard, the stroke color is what the slot represents.
Notes˖ z The stroke colors are only associated with the pen tray slots and have no relation with pen colors. z When pens are in the pen tray, for convenience, the pen colors should be correspondent with the color marks in the pen tray slot. z The pen tray slot has built-in PCBs. Do not put other objects in it. Do not expose the pen tray to liquid. Clean the dust in the pen tray slot with a dry cloth regularly. The pen tray might work abnormally if it is not cleaned for a long time.
Screen Keys Screen keys are called hot keys as well. If the whiteboard is set with hot keys and WhiteBoard is not running, you can run Whiteboard by clicking the hot keys. You can realize the normal functions by clicking the hot keys when the Whiteboard is running.
Different models have different hot key functions. Refer to the above hot key explanations according to the actual models your purchased.
Trouble Shooting Solutions to Problems Problems Phenomenon Presumable Causes Solutions No service program Service program is not Start up the service icon on the right started up. program. bottom of the Service program is not Install the service computer. installed. program. The whiteboard is not Connect the whiteboard connected to the and computer with the computer. USB cable. Interactive whiteboard is not working. The self-checking of Drive icon is red.
move under is same with the desktop operation background color. or background color. mode but cannot write under writing mode. The pen is working but there are deviations. Inaccurate Part of the whiteboard have large deviations. The pen is The strokes do working but not sync with the reactions are writing and there slow. is a delay. Cannot change the The pen tray stroke color when is not picking up or working putting down normally. pen from the pen tray. the calibration.
Specifications Technology Infrared Touch System Pen, Finger Resolution 32767 X 32767 Tracing Velocity 125 P/S Scan Period ≤8ms Consumption(Wired) Power˘1W Port USB Operation System Microsoft Windows XP/Vista/Win7/Win8 Operation Temperature -15°C ~ 50°C Operation Humidity 20~90% Storage Temperature -40°C ~ 50°C Storage Humidity 10~95% 27
We commit ourselves to product upgrading and technology improvement. The contents in this manual are subject to be changed without prior notice. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules.
