Operation Manual

ManualsBrandsSHENZHEN Hitevision Technology ManualsElectronicswireless module

1 / 8

《Operation manual of WLAN module》

VER： V2.0

Product name： Network Module (2019) For Conference Display

Model No. AZ720

Fictioner ： Liu Zhi Yong

Checker ： Zhang Chao Bing

Approver ： Zeng Xiang Long 、Tan Yi

Date ： 2019. 07 . 01

Product Description

The product described in this document is the basic information of network module hardware, and the

unified model name of network module is az720. This module mainly establishes the network foundation for

the large screen customer environment of commercial display. The products respectively support wired and

wireless wan to realize data access to the external network, and provide high-speed and stable wireless hot

spots to meet the terminal wireless internet access and business needs.

Summary of content (8 pages)

PAGE 1
《Operation manual of WLAN module》 VER： V2.0 Product name： Network Module (2019) For Conference Display Model No. AZ720 Fictioner ： Liu Zhi Yong Checker ： Zhang Chao Bing Approver ： Zeng Xiang Long 、Tan Yi Date ： 2019. 07 . 01 Product Description The product described in this document is the basic information of network module hardware, and the unified model name of network module is az720.
PAGE 2
1. Basic information of network module products Hardware interface and function Reset Button Interface distribution: RJ45 DC Interface WIFI 5G FFC Port Name WIFI 2.4G Function Explain It is mainly connected with Android main board through FFC cable to realize module FFC power supply (voltage 12V, current 1.5A). At the same time, it integrates two LAN ports to realize LAN data transmission RJ45 One support 10 \ 100 \ 1000m Ethernet port, realize WAN port data access function Realize the module
PAGE 3
2. General information Product name wireless module Model name. AZ720 FCC ID 2ACYT-AZ720 47 CFR FCC Part 15, Subpart C (Section 15.247) FCC Part 15, Subpart E, Section 15.407 ANSI C63.10:2013 Standard FCC Part 2 (Section 2.1091) KDB 447498 D01 IEEE C95.
PAGE 4
The EUT incorporates a MIMO function. Physically, The EUT provides 2 completed transmitter and 2 receiver: Support mode Transmit and receive mode Transmit and Receive Chain 3. 802.11b MIMO 2TX,2RX 802.11g MIMO 2TX,2RX 802.11a MIMO 2TX,2RX 802.11n HT20 MIMO 2TX,2RX 802.11n HT40 MIMO 2TX,2RX 802.11ac VHT20 MIMO 2TX,2RX 802.11ac VHT40 MIMO 2TX,2RX 802.11ac VHT80 MIMO 2TX,2RX Channels List( operating fundamental frequencies.) For 2.4GHz Band: 11 channels are provided for 802.11b, 802.
PAGE 5
For U-NII-1 4 channels are provided for 802.11a, 802.11a c 20MHz, 802.11n (20MHz): Channel Frequency Channel Frequency 36 5180 MHz 40 5200 MHz 44 5220 MHz 48 5240 MHz 2 channels are provided for 802.11a c 40MHz, 802.11n (40MHz): Channel Frequency Channel Frequency 38 5190 MHz 46 5230 MHz 1 channel is provided for 802.11ac (80MHz): Channel Frequency Channel Frequency 42 5210MHz -- -- For U-NII-3 5 channels are provided for 802.11a, 802.11a c 20MHz, 802.
PAGE 6
4. Product block diagram description 1、The network module is integrated in the display screen, and the power supply and power failure of the module are provided by the internal power bus of the display screen. 2、 The wifi antenna of the network module is installed internally and integrated. The antenna uses IPEX connection interface mode to ensure good contact.
PAGE 7
5. FCC Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 8
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.