LED Interactive Multi-Touch Display User Manual V901.20150420 Please properly keep the manual for further reference. This is the general user manual for all interactive panels. Therefore, it may be different from the actual product.
Welcome: Thanks for purchasing this product. Please read the instructions carefully before using this product. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Contents Safety Instruction ............................................................................................................................. 5 1 Installation Requirement ............................................................................................................ 8 2 Introduction.................................................................................................................................. 10 3 Basic Operation ....................................................
.6.10 Smart Eyes Protection............................................................................................................................................ 60 4.6.11 Reset ...................................................................................................................................................................... 61 4.7 Browser..................................................................................................................................................
Safety Instruction For your safety, please read the following instruction before you use the product. Serious injury or property loss may be caused by improper operations. Do not try to repair the product by your own. Disconnect the product from power supply immediately if major failures occur. The major failures include the following: Smoke, peculiar smell or abnormal sound is discharged from the product. No image or sound is displayed, or the image error occurs.
Do not open the cover or change the product by your own. High voltage components are installed in the product. When you open the cover, high voltage, electric shock or other dangerous situations may occur. If inspection, adjustment or maintenance is required, contact the local distributor for help. Use the specified power supply. Do not use any types of power cables other than the one provided with the product to prevent the product from being damaged.
Do not touch the power cable with wet hands to avoid electric shock. Do not install the product in high temperature environments. Do not install the product near heat source, such as the radiator, the heat reservoir, the stove or other heating devices. Do not expose the product under sunlight, which may cause high temperature and subsequent faults in the product. For transport: Pack the product for mobility or maintenance by using the cartons and cushioning material provided with the product.
1 Installation Requirement Bearing You can install the product in an unfixed or a wall-mounted way based on your needs. The wall-mounted way can save a large amount of space. If the product is installed in an unfixed way, use the designated hanger or holder. If you want to use a self-made hanger or holder, ensure that the bearing capacity of it is at least four times of the weight of the product, and the product is installed stably on it.
When the product is installed in a wall-mounted way, the screws need to be installed deeper than 10 mm in the wall. Do not block ventilation vents. See the installation standard of CAS 132-2006 for reference.
2 Introduction Thank you for choosing our interactive touch screen. As our latest independently developed and produced human-machine interactive product, the hitevision interactive touch screen is a multi-functional display for interactive teaching, digital demonstration, multi-media presentation, touch operations and handwriting.
“*” indicates optional.
Control Panel Name Function Description Home Enter/Exit the Android home page. Return Return to previous menu. Menu Enter/Exit the function menu of screen. ECO Switch among three modes: energy-saving, automatic, and standard. Source Enter the menu to select the signal source. VOL- Decrease volume. VOL+ Increase volume. PC Power Power on or off the OPS. PC The USB 2.0 and USB 3.0 ports for the OPS. Android Android USB port.
Connection Panel 1 Name Function Description Touch Port 1 The touch control terminal 1 which is used to connect to a PC. HDMI 1 The input terminal 1 for high definition signal, which is used with the touch port 1 to operate PC in the way of touch control. MIC The external microphone port. Touch Port 1 corresponds to HDMI 1, and Touch Port 2 corresponds to VGA In, HDMI 2 and HDMI 3.
Connection Panel 2 Name Function Description Audio Out The terminal for external loudspeaker boxes or headphones. Android The USB 2.0 and USB 3.0 ports for connecting to the Android system. SD The external port for the SD card. WAN The port for wide area network, which is used to connect to external network. HDMI Out The output terminal for high definition signal, which can transmit the signal to other display equipment with high definition.
Name Function Description RS232 The input port for series signals, which is used by specific control device of serial port to input serial port protocol in order to control the panel. LAN The port for local area network, which is used to connect to internal network. Touch Port 2 The terminal 2 for touch control signal. HDMI 3 The input terminal 3 for high definition signal, which is used with the touch port 2 to operate PC in the way of touch control.
Name Function Description Video An array of audio and video input terminals, which are used to input audio and video signal. L Video: Video input terminal. R L: Left audio input terminal. R: Right audio input terminal. Please use the cable provided with the product to connect to device.
6. : Show or hide menu. 7. : Show or exit from the list of signal sources. 8. : Enable audio only mode. 9. : Freeze. 10. : Up/Down/Left/Right direction buttons 11. : Confirm. 12. : Capture screen shots. 13. : Show the current signal source. You cannot show it in Android. 14. : Adjust screen displaying. 15. : Open WIFI on the computer. 16. : Change the display mode. 17. : Turn to the previous page on white board software and PPT. 18.
To avoid probable faults, please read the following instructions and use the remote controller properly. Do not drop or beat the remote controller. Do not spill water or other liquid on the remote controller. Do not put the remote controller on wet items. Do not expose the remote controller under sunlight or put it near overheated source.
3 Basic Operation 3.1 Power on Step 1 Power the interactive panel with the 100V-240V 50Hz/60Hz AC power supply. Step 2 Connect the panel to the power supply. Switch on the rocker switch (on the right bottom of the rear of the panel, next to the power port) to enter the standby status. The power indicator turns red.
Step 3 Press power switch on the control panel or Power on the remote controller to turn on the interactive panel. The OPS is started. The power indicator turns green. 3.2 Power off Step 1 Press PC Power to turn off the OPS (for all-in-one models only). Step 2 Press Power on the control panel or Power on the remote controller to enter the standby status. The power indicator turns red. Step 3 In the standby status, switch off the rocker switch to turn off the interactive panel.
Green Powered on 3.3 Software Installation Recommended configuration: − CPU: Inter (R) Core i3 2.27GHz or AMD CPU with equivalent performance − Memory: 1GB − Hard drive: 1GB − Graphics card: supports DirectX 9 or above If the interactive panel is equipped with the latest version of handwriting software in the PC before being delivered, please skip the step. HID drive-free function only applies for Vista, Windows 7or higher version (realize the functions of multi-touch etc.).
3.5 Software Positioning To ensure that the handwriting display works properly, you need to make the handwriting shown on the display coincide with the actual handwriting. The highly accurate coincidence can be achieved by software positioning. Software positioning must be implemented in the following scenarios: The first time to use the interactive handwriting LCD. The driver program is reinstalled. The handwriting display is connected to another PC.
Step 3 Select 9 Points, click Calibrate and the following figure is displayed. Step 4 Use the pen to click and hold the center of the flickering cross. Do not release it until the flickering cross moves to the next point. Repeat and complete the positioning process according to the instructions on the interface. The software interface returns to the desktop automatically after the positioning is completed successfully.
3.6 Positioning in the Windows 7 System Step 1 Connect the interactive panel to PC using the USB cable via the USB interface on the panel; Step 2 Choose Control Panel > Tablet PC Settings. Step 3 Click Calibrate in Tablet PC Settings window.
Step 4 Use the pen to click and hold the center of the flickering cross. Do not release it until the flickering cross moves to the next point. Repeat and complete the positioning process according to instructions on the interface. Step 5 Click Yes after the calibration is completed.
To ensure the handwriting accuracy, use the pen provided with the interactive panel to implement positioning. Do not use your fingers. Positioning errors may cause touch function failure on the interactive panel. In this case, you need to implement positioning again. During the positioning process, you can press ESC on the keyboard to exit the positioning operation. The positioning interface varies among different software versions.
4 Toolbar Introduction The SmartBar includes three modes: Home Page, White Board, and Remarks. In any of the three modes, you can click page and click signal sources. on the toolbar to go back to the previous to exit from other programs or go back to the home page from other On the home page, the SmartBar is in the home page mode and shows icons of the white board, gallery, file manager, system setting, browser and search engine. You can click an icon to open the corresponding program.
Preview external PC, such as the laptop. Preview external portable device, such as U flash disk and SD card. The operation interface for preview is as follows: Click on the SmartBar or press HOME button to enter the home page. The preview window is displayed. When more than three preview windows are displayed, additional windows will be displayed on the second page. Scroll left and right to turn page.
Click any place on the OPS desktop to display the interface information. Click the blank in the SD card preview window to open the SD card portable device. Click on the upper left corner of the home page to show tools, clock, calendar and calculator. Click at the bottom to hide tools and go back to the home page, as shown in the following figure: 4.2 Task Manager In the task manager, you can view current running programs, switch and end programs.
View Running Programs In the task manager, scroll left and right to view current running programs. Switch Programs In the task manger, click an application program icon to switch programs. For example, click Gallery to switch to the gallery application program, or click Browser to switch to the browser application program. End Programs In the task manager, click a program icon and scroll it up or down to end the program. You can also click a program and hold it for several seconds.
4.3 White Board The white board provides the writing function. In the white board program, you can select a pen, line and color to write and use an eraser to erase content on the white board. You can also print and clear the content on the white board. on the SmartBar or press White Board on the remote controller to enter the Click white board interface: New White Board and Settings Click . In the displayed menu, the functions of New Page, Overview, DeleteAll and Settings are listed.
Pen, Line and Color If the marker is selected, click and hold If the highlighter is selected, click and hold for two seconds to set its line and color. for two seconds to set its line and color. Eraser Two methods are available to erase written errors or content as follows: Click to select the eraser, and then you can use it to erase the content on the white board. Use five fingers to touch the screen and a circle is displayed indicating the scope for erasing.
Cancel Click to cancel operations. Screen Capture The following two methods are used to capture screen: Click to capture current content on the white board and save it as an image in ScreenImage directory. (The SmartBar is not captured in the image.) You can open the directory by two ways: − Go back to the home page and click on the SmartBar to enter the file manager. In the system file, find and click the ScreenImage folder to check.
Click a folder to display images in it. View images one by one Click one image in a folder. Scroll left to show the previous image and scroll right to show the next image. In the single image mode, you can click icons on upper right corner of the screen to delete, cut and edit the image. Play slides Click slides.
4.5 File Manager The file manager provides various functions, such as preview, filter, search, select, copy and delete files. 4.5.1 File Preview Click on the SmartBar to enter the file manager interface. Current system files are displayed. External device files are also displayed, such as the files in the SD card and U flash disk.
Preview of external device file
4.5.2 File Filter In the system, documents, images, audios and videos can be displayed by sort to help you find the file. Click icons on the left toolbar to view files by sort. or at the Two ways are available to view the files: by list or by thumbnail.
4.5.3 File Search Click Search on the left toolbar and type keywords in the search box.
The search results can be displayed by sort.
4.5.4 File Operations Click Document operation on upper right corner of the file manager. The functions, select all, select one, copy, delete and cancel, are provided, as shown in the following figure: Click a file: The current file is selected. Select all: All files displayed are selected. Copy: Copy the file selected. Delete: Delete the file selected. Cancel: Cancel current operation. 4.6 System Settings Click on the SmartBar to enter the system settings interface.
4.6.1 Network Click Wireless & network to check the Network status, Wake up via LAN, LAN setting, WiFi setting and WiFi hotspot setting. Select a network connection and set related parameters correctly.
Network Status The network status includes the information about current network connection.
Wake up Via LAN When “Wake up via LAN” function is “ON”, administrator of control center can send requests via LAN using MAC address of touch screen to power on touch screen remotely. To use the function successfully, touch screen should be power off and connected to control center with LAN cable in the same network.
Steps of obtaining MAC address of touch screen: Step 1 Using “SOURCE” on the remote control or “Source” on the front control panel of touch screen to enter Input Source page.
Step 2 Using remote control to enter number “2580” in input signal page to enter “Design Menu” page. Step 3 Click “Ursa Info” in “Design Menu” page to enter “Ursa Info” page and get "WOL_MAC” as MAC address of touch screen.
LAN Setting If the panel is connected with LAN cable and supports Dynamic Host Configuration Protocol (DHCP), the system will automatically configure the internet protocol (IP) value.
If the network protocol needs to be set manually, enter the IP address, default gateway and DNS server parameters by using the soft keyboard or remote controller. or to select the subnet mask to be changed.
WIFI Setting When the Android USB port on the panel is connected with an external wireless card (customized) and WiFi setting is enabled, the system automatically searches available wireless network APs. In the result list, select the AP to be connected.
After an AP with safety authentication is selected, an interface is displayed to ask for the password. You need to enter the password using the soft keyboard to connect to wireless network. WIFI Hotspot Setting When the Android USB port on the panel is connected with an external wireless card (customized) and Portable Wi-Fi hotspot enabled, perform the following operations: Select Portable Wi-Fi Hotspot to set the panel as a WIFI hotspot.
Or, click Set Wi-Fi hotspot and set related WIFI hotspot attributes in the displayed window. 4.6.2 Language and Input Method Click Language and Input method. A setting interface is displayed.
Click Language. Chinese (China) and English are displayed. Click KEYBOARD & INPUT METHODS. Two input methods, AOSP and Google Pinyin, are displayed. You can choose one according to your preference. Click Android Keyboard (AOSP) to enter the related setting interface.
4.6.3 Date and Time Click Date and time to enter the setting interface. Click Select 24-hour mode to set the time format of 24 hours. Otherwise, the time format is displayed as 12-hour time.
Click Select date format to set the date format to be displayed. When Auto sync time and date is selected, the date and time of the system are displayed and you do not need to change them manually. Deselect Auto sync time and date and then you can click Set date, Set time, Set time zone to set the date, time and time zone manually.
4.6.4 Timer Switch Click Scheduled power on/off to enter the interface for setting the automatic startup and shutdown time.
Click Power on time to set the automatic startup time in the displayed window. Click Power off time to set the automatic shutdown time in the displayed window.
4.6.5 Clear Screenshots Click Clear screen shots. A list is displayed and sorted by one month, two months, three months, six months and twelve months. Select a time to clear the screenshots included this period.
4.6.6 Printer Click Printer to enter the printer setting interface. The connecting printer is displayed on the interface. You can also add other printers. The printer type includes Generic BW LaserJet PCL5, Generic Color LaserJet PCL5 and Generic Postscript BW. Printers compatible with the laser printer are supported. (HP, Canon, Brother, Lexmark, Samsung, Xerox) 4.6.7 Storage Click Storage to check the usage of internal storage space and USB storage device in the displayed window.
4.6.8 Application Program Click Application to check the application programs in DOWNLOADED, IN SD CARD, PROCESSING and ALL.
4.6.9 Starting Signals Click Starting signals. On the displayed interface, click Default startup to set the default signal source after each startup.
4.6.10 Smart Eyes Protection Click Smart eyes protection to set Eye protection mode, Eye protection writing mode and Eye protection brightness control mode on the displayed interface.
4.6.11 Reset Click About to check Android version, Activation, Reset, and Firmware update on the displayed interface.
Click Reset and then click OK to restore factory settings. If a new Android version is available, is displayed on the left of Firmware update. Click Firmware update to update the system. 4.7 Browser Click on the SmartBar to open the web browser. Enter a website in the address bar and enter keywords in the search box by using the soft keyboard or remote controller.
4.8 Audio Only Click AUDIO ONLY on the remote controller to turn off the screen but keep audio on. To turn on screen again, touch any place on screen or click AUDIO ONLY again to return to normal operation mode. 4.9 Kids Safety Lock You can turn on/off Kids Safety Lock function via three methods below: Turn on/off the function in Parental Control menu. Step 1 After switching to selected signal source, click MENU on remote controller and choose Parental Control.
Step 3 Kids Safety Lock will be activated after successful setting. To turn on the function, switch to On to lock the device. To turn off the function, change the setting to Off. Press ECO button on the front panel for more than 5 seconds to enter screen locked mode. Under screen locked mode, press ECO for more than 5 seconds again to unlock. Press ECO button on the remote controller for more than 5 seconds to enter screen locked mode.
4.10 Application Programs Click on the SmartBar to enter the application program page. All application programs in the system are displayed.
Calculator Click to enter the calculation page. Click digits and operators on the keyboard to perform calculation. Clock Click timing. to enter the clock page. Click Start to start timing and click Stop to stop Music Click to start the music program. The music in the local disk is displayed by artists, albums, songs, playlist and playing status.
4.11 Temperature Reminder and Thermal Shutdown Temperature Reminder The real-time temperature in the interactive panel is displayed on upper left corner of the home page. Click the temperature display area on the top-left corner of screen to switch between Celsius and Fahrenheit. Thermal Shutdown In the running status, the overall temperature of the panel increases due to unfavorable ventilation environment and long working hours.
5 Signal Channel Selection The following three ways are used to select a signal channel: Press SOURCE on the remote controller. Press Source on the control panel of the interactive panel. Click in the application program page. In the signal source page, press ▲ or ▼ to select a channel and press OK. You can also select directly by clicking an icon, as shown in the following figure: The interactive panel will automatically detect signals when it is started or no signal is available.
6 Menu After switching to selected signal source, press MENU on the remote controller. A menu is displayed, including Picture, Sound Mode, Parental Control and Settings. Scroll left and right on the screen or press ◄ or ► to switch between entries. Picture The Image page displays options including Picture Mode, Color Temperature, Zoom Mode, Image Noise Reduction, and MPEG Noise Reduction. When the picture mode is user, the contrast, brightness, hue, sharpness and saturation are adjustable.
When the sound mode is User, High Pitch and Low Pitch are adjustable. Two ways are used to set the options: Click an icon and set the option. Press ▲ or ▼ to move the cursor onto an option. Press OK and press ◄ or ► to modify the value. Press RETURN to exit the menu. When the sound mode is User, High Pitch and Low Pitch are adjustable. Settings The Settings page displays options including Menu Time, Switch Mode, Color Range, MHL Auto Switch, Movie Mode and Restore To Default.
Parental Control The Parental Control menu shows options including Lock System, Set Password, Block Program, and Kids Safety Lock. There are two ways to set it: Click an icon and set option. Press ▲/▼ to move the cursor onto an option. Press OK and press ◄/► to adjust the value. Press RETURN to quit the menu. This menu is only available when TV signal source is used.
7 ECO Mode Please switch off the panel when it is not used, and enable the function of Listen Alone when you do not need to watch the display, which help reduce power consumption and save energy. On the premise of ensuring viewing effect, the energy consumption can be reduced by lowering display brightness. To better save energy, the automatic power-off function is configured for the panel and the default duration is 10 minutes.
8 Serial Port Control The RS-232 port of the interactive panel is defined as follows: Connect RS-232 port to the PC or controlling device. Enable RS-232 serial port connection and complete the following configuration. Port Number: COM 1 (Set the value according to the port number of the PC or controlling device.) Bit rate 19200 Odd/even check None Data bit 8 Stop bit 1 The following table lists button controlling codes.
Function Controlling Code Function Controlling Code Signal source 7F 08 99 A2 B3 C4 02 FF 01 06 CF 5 7F 08 99 A2 B3 C4 02 FF 01 25 CF Display status 7F 08 99 A2 B3 C4 02 FF 01 09 CF 6 7F 08 99 A2 B3 C4 02 FF 01 26 CF HDMI 1 7F 08 99 A2 B3 C4 02 FF 01 0A CF 7 7F 08 99 A2 B3 C4 02 FF 01 27 CF HDMI 2 7F 08 99 A2 B3 C4 02 FF 01 0B CF 8 7F 08 99 A2 B3 C4 02 FF 01 28 CF HDMI 3 7F 08 99 A2 B3 C4 02 FF 01 0C CF 9 7F 08 99 A2 B3 C4 02 FF 01 29 CF OPS (HDMI 4) 7F 08 99 A2 B3 C4 02 FF 01 38 CF
9 VGA Signal Input VGA (Video Graphics Array) is the computer display standard for analog signal. VGA port is the special port on the computer which uses the VGA standard for data input. The following table lists the specifications of various VGA signal input. The VGA signal input is available only when the panel is in PC mode. SN Standard Resolution Refresh Rate (Hz) Horizontal Frequency (Khz) Vertical Frequency (Hz) Horizont al/Vertic al Sync Polarity (TTL) 1 VESA 640x480 60 31.
10 Multimedia Format Support Media Type File Format File Extension Image JPEG, BMP, PNG .jpg, .bmp, .png Movie MPEG1, MPEG2, MPEG4, H264, RM, RMVB, VC1, Divx, FLV .avi, mpg, .dat, .vob, .div, .mov, .mkv,.r m, .rmvb, .mp4, .ts, .trp, .asf, .flv Music WMA, MP3, M4A, (AAC) .mp3, .m4a Text TXT .
11 Symptom Common Faults and Solutions Possible Cause Solution The drive program is not correctly installed. Install the drive program correctly. The USB port (lead) is not connected or is faulty. Change the USB lead or check if the USB port is faulty. The infrared tube is blocked. Ensure that the surrounding infrared tubes are not blocked. Repositioning is required every time the panel is switched on. The computer is equipped with a recovery card.
Symptom The handwriting cannot be displayed. Not sound is played and no image is displayed. Image is displayed properly, but no sound is played. No image is displayed or the image is black and white. Possible Cause Solution The covering area of the nib does not meet the requirement or the nib is too small. Change the nib or use a pen with larger covering area. The infrared tube is blocked. Check if infrared tubes are blocked. Strong light or infrared interference exists.
Symptom The image or sound is interrupted. The remote controller fails. The PC cannot be started. (This scenario is applicable only to panel models operating with the PC.) Possible Cause Solution Find out the electric appliance that causes the interference and move it away from the interactive panel. Do not share the power socket of the panel with the electric appliance that causes interference. Change the batteries. Clean the signal emitter at the top of the remote controller.
12 Care and Maintenance Maintenance Tips Do not put or install the product near a heat source or under direct sunlight, or in dusty or humid places, or somewhere the product may be hit or damaged by mechanical vibration. To maximize the performance, it needs to be put away from equipment such as grid, large metal objects and radar stations as far as possible. Do not wipe the panel with any chemical reagent. Solvents may damage the enclosure or paint.
13 Technical Parameters Specification Parameter Backlight type LED Aspect ratio 16:9 Viewing angle 178° Physical resolution 1920x1080 Pixel Image/Sound system PAL/DK, I Working voltage 100V-240V, 50 Hz /60Hz Standby power consumption ≤0.
