User's Manual

HSD9042E
Instruction Manual
Main Features & Technical Parameters
● Power supply: input AC 100-240V 50/60Hz, output
DC13V/1.2A
● Rated working current: 1.2A
● Rated consumption power: 18W
● Lighting rated power: 8W
● Rated ambient temperature: t
a
…40℃
● Dimmer: sensor touch, 5 levels lights
● Timer: smart timing shutdown
● Light source: 40 pcs of LEDs
● Light mode: Natural—White—Yellow light
● Color temperature: 2700-6500K
● CRI: Ra≥90
● Max illuminance:≥1000LUX(measured 33CM from lamp
shade to desk）
● Wireless charging output: 5V/1A(MAX)
Operating Instruction
1. Turn on the lamp: put the lamp on table positively,
connect the adapter, short press the " " symbol to turn on
the lamp, the default for open the lamp is natural light.
Short press again to shut down the light. Short touch press
"M" to switch light mode circularly: natural—white—yellow.
2. Lamp brightness: after lamp turned on, short press " "
or " " to adjust the brightness.
3. Timer: when light turned on, extended press " " to turn
on the timer function in any circumstance, at the same time
the light flashes 2 times, then lamp would shut down in
40mins(a period of one lesson). Timer function would reset
if you extended press " " again. Lamp will shut down
automatically until count down is over.
Wireless Charging Instruction
1. Wireless charging function: when lamp power supply is
on, putting a mobile phone which with wireless receiver
function(or a mobile phone with wireless charging receiver
module) on the desk lamp of wireless charging icon in the
center area, observing the power icon on the phone, such
as display is charging, explain the phone has been in a
state of wireless charging. Meanwhile, wireless charging
indicator turns to green.
2. For the best use effect of wireless charging function, to
get higher charging efficiency, please pay attention to
wireless receiving position of mobile phone, it should be
fully exposed to wireless charging icon on the surface of
the desk lamp and in the central area. If don’t exposed fully
on the icon, the green indicator light will flash. When
devices fully power charged, green and red indicator will be
on at the same time.
3. Light and wireless charging functions can be used at the
same time.
Cautions
1. This product power is supplied by adapter DC13V/1.2A.
If the adapter or cable is damaged, please ask the
manufacturer, agent or any qualified people for help.
2. This product shall be used indoor only.
3. While the LED light on, do not shine on eyes in short
distance to prevent eye injury.
4. This product might be turned on or off under strong
electromagnetic wave.
5. Part of the lamp pole is not available to bend, otherwise it
might be damaged. Please do not bend the silicone part so
often in case it might be damaged.
6. The light source of this lamp cannot be replaced, when
the light source servers to its end, should replace the whole
lamp.
7. This product may tip over when used on a table with a
slope greater than 6°.
Product Illustration
Packing Accessories
1. Adapter * 1.
2. User Manual *1
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a
residential installation. This equipment generates uses and
can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician
for help
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's