User's Manual

User Manual
*Please read the user's manual carefully before operation.
The illustrations in the manual are only for your reference, please in kind prevail.
This product is a smart photoelectric smoke sensor,
with ultra-low-power Z-Wave wireless network
technology design. It is an warning device, cannot
sense gas, heat, or flame, cannot prevent or put out
fire.Real-time detecting the presence of smoke,
detection of visible particles(smoldering fire) faster
than ionization smoke alarms. Red LED flashes
rapidly and detectors sound alarm once detecting
smoke fire danger, it can alert you and your family
timely. Smoke alarms should be installed in all
rooms, living room, storage areas, basements and
atticsunit that fire may happen.
1. This sensor is designed specifically for home use, may
not able to provide sufficient fire alert for public areas.
2. Please avoid installation in bathrooms and other very
humid places, dusty or greasy areas, or very airy place
with air conditioner, ceiling fans,etc.
3. Please keep sensor clean, and do not let dust
accumulated. It is recommended to be cleaned every
6 months with a household cleaner and a soft brush.
4. The effective lifespan is 10 years. Replacement every
10 years, regardless of sensors breakdown or not (
battery lifespan: 3 years).
5. Please pay attention if it alarms. Besides proper use of
sensor, we should also strengthen the consciousness
of fire safety.
Flat ceiling mounting
The preferred location to install smoke sensor is in the
centre of the ceiling, because smoke, heat and
combustible products rise to ceiling and will laterally
spread.Keep at least 30cm distance from lights or
decorations, and at least 15 cm away from walls and
corners.
Sloping ceiling mounting
If ceiling is sloping, please install the smoke sensor at
horizontal distance 90cm away from the ceiling top.
Rotate the anticlockwise to separate from
bracket, then remove battery insulating strip to electrify
the .
sensor
sensor
Attach the sensor to the mounting bracket and turn
clockwise to lock into place. Remove the membrane of
double sided adhesive tape on the mounting bracket.
please refer to the following situations, if the sensor can
not work normally:
1.Battery reaches service life (status refer to form 1).
Pleasereplace the battery.
2.Fault affected by dirt with dust or oil, etc (status refer to
Form 1). Please clean the alarm correctly.
3.Whether the alarm is properly rotated into the mounting
bracket.
Please make sure there is no real fire danger when using
hush function. If non-emergency smoke(e.g. Steam)
causes nuisance alarms, please do not stop alarm by
block smoke detector or in other forms. You could press
the hush/test button to stop alarm temporarily.(Ten
minutes later, the smoke detector will be back to normal
working condition)
Press and release the test button to test the alarm. The
alarm will sound loud short beeps. It means the smoke
detector can work normally. The alarm may stop sounding
once releasing the test button. It is suggested to test the
smoke alarm at least one time every week. Do not use an
open flame to test this smoke alarm.
Please replace battery correctly according to the positive
and negative electrode. Dispose of used battery in right
way. Pay attention to environmental protection.
Dead air area
Hush Function
OFF
TWIST
ON
Product Introduction
Technical Deta
Product Details
Bracket
Alarm
Test/Hush Button
and LED Indicator
Tips
1. Working Voltage: DC3V(CR123A lithium battery)
2. Static Current: ≤10uA
3. Alarm Current: ≤60mA
4. Networking: Z-Wave Ad-Hoc Networking
5. Sound Level: ≥85dB/3m
6. Distance Of Networking: ≥70m (open area)
7. Working Temperature: -10°C ~ +50°C
8. Working Humidity: ≤95% RH
9. Dimension: 60×60×49.2mm
Recommended and Avoided
Installation Position
Sloping Ceiling
Mounting Position
Installation Step 1
Installstion Renderings
Installation Step 2
Status and Troubleshooting
Status
Light
Alarm Sound
Normal
Testing
Red LED flashes every 53 seconds.
Red LED flashse quickly
No
Rapid beeps
Hush mode
Red LED Flashes one time every 10 seconds.
one beep every
53 seconds
Low Power
Red LED flashes one time every 53 seconds.
two beeps every
53 seconds
Red LED flashse quickly
Alarm
Red LED flashes two times every 53 seconds.
Rapid beeps
No
Fault
Mute and Test
Battery Replacement
Statement
*Instruction is for reference only, please prevail in kind.
*Because of the updating of the technology, the final
interpretation right owned by factory, if there are any
inconformities when using this products under this instruction.
1
2
3
4
5 6
7
8 9 10 11 12 13
Networking Hole
Detector will enter the network mode by clicking “ ” in the
APP.
Installation Step 3 Installation Step 4
OFF
TWIST
ON
Connecting network:
hole for 2 seconds till green LED flash quickly, APP shows slip,
green LED keep on for 3 seconds, networking succeed.
Disconnecting network: Press the networking button for 5
seconds to disconnect the network, after the green light
flashes slowly for 3 seconds, which indicates network is
disconnected successfully.
According to APP prompt, press networking
Form1
Smart Smoke Sensor
HS1SA-Z