User's Manual

Smart Carbon Monoxide Sensor
User Manual
Click “Add Device” on the APP interface, and
enter the networking mode.
Technical Data
Tips
Installation Instruction
Installation Drawing
Product Introduction
* Ple ase re a d t he use r ma n ua l ca r ef u ll y be for e o per ati on.
The g uid e pictu r e is f or r e fer e n c e o n l y. please in k i n d pr e v a il
1.Install the sensor in bedroom and living area or
anywhere CO may leak, make sure each sleeping
ar ea ca n hea r sou nd al ar m whe n cho o se
installation position.
2.Avoid suppressing or falling down sensors, keep
sensors away from humid, high voltage, strong
magnetic and children.
3.Do not suggest install sensors in garage, kitchen,
boiler and places where sensor may false alarm.
Do not install in dirty, dusty or greasy places, oily,
dust or household chemicals may damage internal
sensor, and make sensor can not work normally.
4.Sensors can support wall mounted or placing on
the table, household and travel essential.
Screw the sensor into bracket, please remove the
double - sided adhesive membrane on the
installation base, and stick on the wall.
Sen sor
Ins tal lat i on Base
Anticlockwise rotating the bracket out from the installation
base, then remove the battery insulating strip to make
detector on power.
*Please replace battery correctly, following the battery posi
negative electrode.
tive and
Green- flash alternatively oncered-yellow-green LED
Green,red and yellow LED flash alternatively once
Red LED flash
Yellow LED flash twice every 10 seconds
Green LED flash every 53 seconds
Red LED flash every 53 seconds
Yellow LED flash twice
4 beeps
1 beep
4 beeps
2 beeps every 10 seconds
1 beep every 53 seconds
\
4 beeps every 10 seconds
Status
LED Indicator
Alarm
Please take following advices for reference if sensors can not work normally:
1.Replace battery in time, if voltage too low and reach effective life span.
(Check table 1 for state reference)
2.Please clean sensor if the fault resulted from dust or oil stain ( Check table
1for state reference).
3.Make sure sensors screw into the base correctly.
Press test button on the product for 3 seconds, shows in above
picture, till alarm happens ( check table 1 for state reference).
Suggest test sensor at least once a week. Please pay attention once
alarm happens.
Installation Step1
Installation Step2
Installation Step3
Installation Step4
Chart1
CR
1
2
3
A
1, This product can not be used for detecting natural
ga s ( m et h an e ), pr o pa n e , bu ta n e and ot h er
combustible gas.
2, Clean once a month, users may use household
vacuum cleaner and soft brush when cleaning.
3, Do not use cleanser or solvent wipe sensors,
please avoid spraying air freshener, hair spray, oil
paint or other aerosol near sensors.
4, Effective working life span is 5 years, suggest
replace every 5 years no matter there is fault or
not. (Battery life span is 3 years).
5, Please be attention when alarm happens. Shut-off
valves immediately, opening the window, make
sure indoor airiness. Besides using sensors
c o r r e c t l y, u s e r s s h o u l d s t r e n g t h e n t h e
consciousness of fire protection.
Test
Preheating
Alarm
Malfunction
Low battery
Normal working
Expired sensor
Status and battery replacement
Troubleshooting and test
Minimum recommended installation
Additional recommended installation
Bedroom
Bedroon
Bedroom
Livingroom
Kitchen
Basement
Gagrage
Aisle
To increase safety factors in single-layer house,
suggest to install at least a sensor in each bedroom and
install a sensor at 6m from chimney and gas fixture.
To increase safety factors in multi-layer house, suggest
to install at least a sensor in each bedroom, install at
least one sensor in basement. Please install a sensor at
6m from chimney and gas fixture.
Networking Hole
LED Indicator
According to APP prompt, press the networking button 3 times in
1.5 seconds until green light flash, (the longest networking time
is 30 seconds) APP interface prompted, networking success.
Select device, click "delete" on APP, then press the
networking button 3 times in 1.5 seconds until the green light
flashes slowly for 6 times, which indicates network is
disconnected successfully
T his p rod uct i s a sma r t car bon m ono xid e
sen sor, a dop t s su per low power cons ump t ion Z-
wav e wirel ess ne two rki ng tec hno log y, used for
det ect ing carb on monox ide . S ens or adop ts high
per fo rm an ce ele ct ro ch emi ca l sen so r, sup po rt
sou nd and fl ash al arm , I t h as hig h s t abi lit y, sup er
low po wer c ons ump tio n, li t tle s ens iti vit y dri ft and
man y ot her fea tur es. Fre e in sta lla tio n d e sig n,
sup por t ins t ant b ond ing .
1.Working Voltage：DC3V(CR123A Lithium Battery)
2.S tatic Current：≤20uA
3.Alarm Current：≤60mA
4.A lar m So und：8 5dB /1m
5.A lar m Se nsi tiv ity：3 0pp m 1 20m ins alar m
50 ppm 60- 90m ins alar m
10 0pp m 1 0-4 0mi ns a lar m
30 0pp m 3 min s al arm
6.N etw ork i ng：Z- wav e Ad-H oc Netw ork i ng
7.W ireless Networking Distance：≥70m(open area)
8. Work ing Temper atu re：-10℃ ～ +50℃
9.E nvi ron m ent Hum idi ty：≤ 95% RH
10. Dim ens i on：60 * 6 0*4 9.2 mm
7
6 8 9 10
11
1 2
3
4
5
HS1CA-Z