Gaw9.
Contents 1 2 3 Introduction..................................................................................................... 1 1.1 Safety Precautions .............................................................................. 1 1.2 LEDs and Interfaces............................................................................ 2 1.3 System Requirements ......................................................................... 4 1.4 Features.............................................................
4 3.6.4 QoS ........................................................................................ 64 3.6.5 SNMP ..................................................................................... 65 3.6.6 Others..................................................................................... 66 3.7 Admin................................................................................................ 67 3.7.1 Commit/Reboot....................................................................... 67 3.
1 Introduction The ADSL Router supports multiple line modes. It provides four 10/100 base-T Ethernet interfaces at the user end. The device provides high-speed ADSL broadband connection to the Internet or Intranet for high-end users, such as net bars and office users. The device provides high performance access to the Internet, downlink up to 24 Mbps and uplink up to 1 Mbps. The device supports WLAN access, as WLAN AP or WLAN router, to the Internet. It complies with IEEE 802.11, 802.
1.2 LEDs and Interfaces Front Panel The following table describes the LEDs of the device: LEDs Color Green PWR Red Link Green Status Description On The device is powered on. Off The device is powered off. On The device is self-testing or self-testing is failed, or the software is upgrading. On The device has established connection with the office physical layer. Blinks (fast) The device is handshaking with the office physical layer. Blinks (slow) The device does not detect the signals.
LEDs Color Status Description The device has successful WLAN connection. On WLAN WPS Green Green Blinks Data is being transmitted on WLAN. Off The WLAN connection is failed. Off WPS is disabled. Blinks WPS is enabled, and is waiting for client to negotiate. Rear Panel The following table describes the interfaces of the device: Interface Description Wireless antenna. Line RJ-11 interface, for connecting to the ADSL interface or a splitter through a telephone cable.
Interface ON/OFF 1.3 Description Power switch, power on or power off the router. System Requirements Recommended system requirements are as follows: A 10/100 base-T Ethernet card is installed on your PC A hub or Switch. (attached to several PCs through one of Ethernet interfaces on the device) Operating system: Windows 98SE, Windows 2000, Windows ME, Windows XP or Windows Vista Internet Explorer V5.0 or higher, Netscape V4.0 or higher, or firefox 1.5 or higher 1.
1.5 PPP session PAP/CHAP IP/Port, MAC, URL filter Remote access control Line connection status test Remote access control Backup and restoration of configuration file IP quality of service (QoS) Universal plug and play (UPnP) WLAN with high-speed data transmission rate, up to 54 Mbps, compatible with IEEE 802.11b/g, 2.4 GHz compliant equipment Supported Protocols The device supports the following protocols: ITU G.992.1 (G.DMT) Annex A ITU G.992.2 (G.LITE) ANSI T1.
2 Hardware Installation Step 1 Connect the Line interface of the device and the Modem interface of the splitter through a telephone cable. Connect the phone to the Phone interface of the splitter through a cable. Connect the incoming line to the Line interface of the splitter. The splitter has three interfaces: Line: Connect to a wall phone jack (RJ-11 jack) Modem: Connect to the ADSL jack of the device Phone: Connect to a telephone set.
Figure 1 Connection diagram (Without connecting telephone sets before the splitter) Connection 2 Figure 2 shows the connection when the splitter is installed close to the router. Figure 2 Connection diagram (Connecting a telephone set before the splitter) Note: When connection 2 is used, the filter must be installed close to the telephone cable. See Figure2. Do not use the splitter to replace the filter.
you must add a microfilter before a telephone set. Do not connect several telephones before the splitter or connect several telephones with the microfilter. Wall Mount Diagram The device can be mounted on the wall. Figure 3 shows the wall mount diagram.
3 About the Web Configuration This chapter describes how to configure the router by using the Web-based configuration utility. 3.1 How to Access the Router The following is the detailed description of accesing the router for the first time. Step 1 Open the Internet Explorer (IE) browser and enter http://192.168.1.1. Step 2 In the LOGIN page that is displayed, enter the username and password. The username and password of the super user are admin and admin respectively.
If you log in as a common user, you can check the status of the router, but can not configure the most of the settings. 3.2 Wizard When subscribing to a broadband service, you should be aware of the method by which you are connected to the Internet. Your physical WAN device can be either PPP, ADSL, or both. The technical information about the properties of your Internet connection is provided by your Internet Service Provider (ISP).
Enter the correct password and then click NEXT. The page shown in the following figure appears. In this page, you can set the system time and Network Time Protocol (NTP) server. The following table describes the parameters of this page: Description Field State You can disable or enable NTP function. You have to enable it if you want to configure the parameters in this page. Server IP Enter the IP address of the specified time server manually.
Description Field Interval Set the interval that the router obtains the time from the time server. That is, the interval that the router verifies the time with the server. Time Zone Choose the time zone of your country. GMT time It displays the Greenwich mean time. After finishing the configuration, click NEXT. The page shown in the following figure appears.
Description Field ISP. You can select LLC/SNAP or VC-Mux. Channel Mode Select the WAN connection type. You can select 1483 Bridged, 1483 MER, PPP over Ethernet (PPPoE), PPP over ATM (PPPoA), or 1483 Routed. PPP Settings The username and password apply to PPPoE and PPPoA encapsulation only. Ensure that you enter the correct username and password. Default Route You can select Enable or Disable.
Description Field set the parameters in this page. Band Choose the working mode of the router. You can choose 2.4 GHz (B), 2.4 GHz (G), or 2.4 GHz (B + G). By defaut, the band is 2.4 GHz (B + G). SSID The service set identification (SSID) is a unique name to identify the router in the wireless LAN. Wireless stations associating to the router must have the same SSID. Enter a descriptive name that is used when the wireless client connecting to the router.
1483 Bridged In the Setup WAN Interface page, set the channel mode to 1483 Bridged 1483 MER 15
In the Setup WAN Interface page, set the channel mode to 1483 MER PPPoE 16
In the Setup WAN Interface page, set the channel mode to PPPoE PPPoA 17
In the Setup WAN Interface page, set the channel mode to PPPoA 1483 Routed 18
In the Setup WAN Interface page, set the channel mode to 1483 Routed 3.3 Status In the navigation bar, choose Status. In the Status page that is displayed contains: System, LAN, WLAN, WAN, Port Mapping, Statistic, and ARP Table. 3.3.1 System Choose Status > System. The page that is displayed shows the current status and some basic settings of the router, such as software version, DSP version, uptime, upstream speed, and downstream speed.
3.3.2 LAN Choose Status > LAN. The page that is displayed shows some basic LAN settings of the router. In this page, you can view the LAN IP address, DHCP server status, MAC address, and DHCP client table. If you want to configure the LAN network, refer to chapter 3.4.1.1 LAN IP. 3.3.3 WLAN Choose Status > WLAN. The page that is displayed shows some basic WLAN settings of the router. In this page, you can view basic status of WAN and DNS server.
3.3.4 WAN Choose Status > WAN. The page that is displayed shows some basic WAN settings of the router. In this page, you can view basic status of WAN and DNS server. If you want to configure the WAN network, refer to chapter 3.4.2.1 WAN.
3.3.5 Port Mapping Choose Status > Port Mapping. In this page, you can view the mapping relation and the status of port mapping. 3.3.6 Statistics Choose Status > Statistics. The Statistics page that is displayed contains Traffic Statistic and DSL Statistic. 3.3.6.1 Traffic Statistic Click Traffic Statistic in the left pane. The page shown in the following figure appears. In this page, you can view the statistics of each network port.
3.3.6.2 DSL Statistic Click DSL Statistic in the left pane. The page shown in the following figure appears. In this page, you can view the ADSL line status, upstream rate, downstream rate, and other information.
3.3.7 ARP Table Choose Status > ARP Table. In the ARP Table page, you can view the table that shows a list of learned MAC addresses. 3.4 Network In the navigation bar, choose Network. The Network page that is displayed contains LAN, WAN, and WLAN.
3.4.1 LAN Choose Network > LAN. The LAN page that is displayed contains LAN IP, DHCP, and DHCP Static IP. 3.4.1.1 LAN IP Click LAN IP in the left pane. The page shown in the following figure appears. In this page, you can change IP address of the router. The default IP address is 192.168.1.1. This is the private IP address of the router. This is the address under which the router can be reached in the local network. It can be freely assigned from the block of available addresses.
3.4.1.2 DHCP Dynamic Host Configuration Protocol (DHCP) allows the individual PC to obain the TCP/IP configuration from the centralized DHCP server. You can configure this router as a DHCP server or disable it. The DHCP server can assign IP address, IP default gateway, and DNS server to DHCP clients. This router can also act as a surrogate DHCP server (DHCP proxy) where it relays IP address assignment from an actual real DHCP server to clients. You can enable or disable DHCP server or DHCP proxy.
Field Show Client Default Gateway Description Click it, the Active DHCP Client Table page appears. It shows the assigned IP address of the clients. Enter the IP default gateway of the IP address pool. Max Lease Time The lease time determines the period that the PCs retain the assigned IP addresses before the IP addresses change. Domain Name Enter the domain name if you know. If you leave this blank, the domain name obtained by DHCP from the ISP is used.
Field Description example, 00-A0-C5-00-02-12. Expired (s) It displays the lease time. The lease time determines the period that the PCs retain the assigned IP addresses before the IP addresses change. Refresh Click it to refresh this page. Close Click it to close this page. Click Set VendorClass IP Range in the DHCP Settings page. The page shown in the following figure appears. You can configure the IP address range based on device type. Choose None in the DHCP Settings page.
Choose DHCP Relay in the DHCP Mode page. The page shown in the following figure appears. The following table describes the parameters of this page: Field Description DHCP Mode If set to DHCP Relay, the router acts a surrogate DHCP Server and relays the DHCP requests and reponses between the remote server and the client. Relay Server Enter the DHCP server address provided by your ISP.
3.4.1.3 DHCP Static IP Click DHCP Static IP in the left pane. The page shown in the following figure appears. You can assign the IP addresses on the LAN to the specific individual PCs based on their MAC address. The following table describes the parameters and buttons of this page: Field Description IP Address It specifies the IP address of the IP address pool. Mac Address Enter the MAC address of a PC on the LAN. Add After entering the IP address and MAC address, click it.
In this page, you can configure WAN interface of your router. The following table describes the parameters of this page: Field Description Default Route Selection You can choose Auto or Specified. VPI The virtual path between two points in an ATM network, ranging from 0 to 255. VCI The virtual channel between two points in an ATM network, ranging from 32 to 65535 (1 to 31 are reserved for known protocols) Encapsulation You can choose LLC and VC-Mux.
Field Description PPP Settings User Name The correct user name that your ISP has provided to you. Password The correct password that your ISP has provided to you. Type You can choose Continuous, Connect on Demand, or Manual. Idle Time (min) If select connect on demand, you need to enter the idle timeout time. Within the preset minutes, if the router does not detect the flow of the user continuously, the router automatically disconnects the PPPoE connection.
Field Current ATM VC Table Description This table shows the existed PVCs. It shows the Interface name, channel mode, VPI/VCI, encapsulation mode, local IP address, remote IP address and other information. The maximum item of this table is eight. Click it, the PPP Interface-Modify page appears. You can modify the PVCs’ parameters. Click in the PPPoE mode. The page shown in the following figure appears. In this page, you can configure parameters of this PPPoE PVC.
Field Description this PPP interface (VPI/VCI). Login Name The login name provided by your ISP. Password The password provided by your ISP. Authentication Method You can choose AUTO, CHAP, or PAP. Connection Type You can choose Continuous, Connect on Demand, or Manual. Idle Time (s) If choose Connect on Demand, you need to enter the idle timeout time.
The following table describes the parameters and buttons of this page: Field Description VPI The virtual path identifier of the ATM PVC. VCI The virtual channel identifier of the ATM PVC. QoS The QoS category of the PVC. You can choose UBR, CBR, rt-VBR, or nrt-VBR. PCR The maximum rate at which cells can be transported along a connection in the ATM network. CDVT The amount of delay permitted between ATM cells (expressed in microseconds).
In this pae, you can select the DSL modulation. Mostly, you need to remain this factory default settings. The router supports these modulations: G.lite, G.Dmt, T1.413, ADSL2, ADSL2+, AnnexL, and AnnexM. The router negotiates the modulation modes with the DSLAM. 3.4.3 WLAN Choose Network > WLAN. In the WLAN page that is displayed contains Basic Setting, Security, Access Control, multi-SSID, Advance Setting, and WPS. 3.4.3.1 Basic Setting Click Basic Setting in the left pane.
The following table describes the parameters and buttons of this page: Field Description Band Choose the working mode of the router. You can choose 2.4 GHz (B), 2.4 GHz (G), or 2.4 GHz (B + G). By defaut, the band is 2.4 GHz (B + G). Mode Choose the network modle of the router, which is varied according to the software. By defaut, the network model of the router is AP. SSID The service set identification (SSID) is a unique name to identify the router in the wireless LAN.
Field Description Choose a channel from the drop-down list box. Radio Power (Percent) You can choose the transmission power of the radio signal. It is recommended to choose the default value 100%. Show Active Clients Click it to view the information of the wireless clients that are connected to the router. Apply Changes Click it to save the settings of this page. 3.4.3.2 Security Click Security in the left pane. The page shown in the following figure appears.
Field Description choose None, WEP, WPA (TKIP), WPA (AES), WPA2 (AES), WPA2 (TKIP), or WPA2 Mixed. Wired equivalent privacy (WEP) encrypts data frames before transmitting over the wireless network. Wi-Fi protected access (WPA) is a subset of the IEEE802.11i security specification draft. WPA2 Mixed is the collection of WPA and WPA2 encryption modes. The wireless client establishes the connection between the router through WPA or WPA2.
The following describes the parameters and button of this page: Field Description Key Length Choose the WEP key lenth. You can Choose 64-bit or 128-bit. Key Format If you choose 64-bit, you can choose ASCII (5 characters) or Hex (10 characters). If you choose 128-bit, you can choose ASCII (13 characters) or Hex (26 characters). Default Tx Key Choose the index of WEP Key. You can choose Key 1, Key 2, Key 3, or Key 4. Encryption Key 1 to 4 The Encryption keys are used to encrypt the data.
Field Description If you choose 128-bit and ASCII (13 characters), enter any 13 ASCII characters. If you choose 128-bit and Hex (26 characters), enter any 26 hexadecimal characters. Apply Changes 3.4.3.3 Click it to save the settings of this page. Access Control Click Advanced Setting in the left pane. The page shown in the following figure appears. In this page, you can configure the access control of the wireless clients.
3.4.3.4 multi-SSID Click multi-SSID in the left pane. The page shown in the following figure appears. The following table describes parameterand button of this page: Field Description SSID The service set identification (SSID) is a unique name to identify the router in the wireless LAN. Apply Changes Click it to save the settings of this page.
3.4.3.5 Advance Setting Click Advance Setting in the left pane. The page shown in the following figure appears. In this page, you can configure the wireless advanced parameters. It is recommended to use the default parameters. Note: The parameters in the Wireless Advanced Settings page are modified by the professional personnel, it is recommended to keep the default values.
Field Description In the encryption authentication, the wireless client connects to the router through the shared key. Data Rate Choose the transmission rate of the wireless data. You can choose Auto, 1 M, 2 M, 5.5 M, 11 M, 6 M, 9 M, 12 M, 18 M, 24 M, 36 M, 48 M, or 54 M. Broadcast SSID Select whether the router broadcasts SSID or not. You can select Enable or Disable. Select Enable, the wireless client searchs the router through broadcasting SSID.
WPS Authentication: The WPS service is enabled by default. There are there methods used in the Wi-Fi Protected Setup. In order to use wps authentication, you can select one method from the following there methods. Press the WPS button on the rear panel for more than 3 seconds. The router generates PIN, see the above figure. Click Regenerate PIN to generate a new PIN, then click Start PCB, press WPS button on the wireless client simultaneously.
not know how to translate a particular domain name, it asks another one, and so on, until the correct IP address is returned. The following table describes the parameters and buttons of this page: Field Description Attain DNS Automatically Select it, the router accepts the first received DNS assignment from one of the PPPoA, PPPoE or MER enabled PVC(s) during the connection establishment. Set DNS Manually Select it, enter the primary and optional secondary DNS server IP addresses.
The following table describes the parameters of this page: Field Description DDNS provider Choose the DDNS provider name. Hostname The DDNS identifier. Interface The WAN interface of the router. Enable Enable or disable DDNS function. Username The name provided by DDNS provider. Password The password provided by DDNS provider. Email The email provided by DDNS provider. Key The key provided by DDNS provider. 3.5.2 Firewall Choose Service > Firewall.
3.5.2.1 IPPort Filter Click IPPort Filter in the left pane. The page shown in the following figure appears. Entries in this table are used to restrict certain types of data packets through the gateway. These filters are helpful in securing or restricting your local network. Click Apply Changes to save the settings of this page. Click Add to add a new rule of the IP/Port filter. 3.5.2.2 MAC Filter Click MAC Filter in the left pane. The page shown in the following figure appears.
Click Apply Changes to save the settings of this page. Click Add to add a new rule of the MAC filter. 3.5.2.3 URL Blocking Click URL Blocking in the left pane. The page shown in the following figure appears. This page is used to block a fully qualified domain name (FQDN), such as tw.yahoo.comand and filtered keyword. You can add or delete FQDN and filtered keyword.
The following table describes the parameters and buttons of this page: Field Description URL Blocking Capability You can choose Disable or Enable. Choose Disabled to turn off URL blocking and keyword filtering. Choose Enable to block access to the URLs and keywords specified in the URL Blocking Table and Keyword Filtering Table. Apply Changes Click it to save the settings of this page. Keyword The keyword to block. Add Keyword Click it to add the keyword to the keyword filtering table.
The following table describes the parameters of this page: Field Description Service Type You can choose the common service type, such as AUTH, DNS, or FTP. You can also define a service name. If you choose the common service type, the corresponding WAN communication port/service host communication port has the default settings. If you define service type, you need to enter the corresponding port. Protocol Choose the transport layer protocol that the service type uses. You can choose TCP or UDP.
3.5.2.5 DMZ Setting Click DMZ Setting in the left pane. The page shown in the following figure appears. A demilitarized zone is used to provide Internet services without sacrificing unauthorized access to its local private network. Typically, the DMZ host contains services accessible to Internet traffic, such as web (HTTP) servers, FTP servers, SMTP (e-mail) servers and DNS servers. Step 1 Select Enable DMZ to enable this function. Step 2 Enter an IP address of the DMZ host.
3.5.3 UPNP Choose Service > UPNP. The page shown in the following figure appears. This page is used to configure UPnP. The system acts as a daemon after you enable it.
3.5.4 IGMP Proxy Choose Service > IGMP Proxy in the left pane. The page shown in the following figure appears. IGMP proxy enables the system to issue IGMP host messages on behalf of hosts that the system discovered through standard IGMP interfaces. The system acts as a proxy for its hosts after you enable it. 3.5.5 TR069 Choose Service > TR069. The page shown in the following page appears. In this page, you can configure the TR-069 of the router.
The following table describes the parameters and buttons of this page.
Field URL Description The URL of the auto-configuration server to connect to. User Name The user name for logging in to the ACS. Password The password for logging in to the ACS. Periodic Inform Enable Select Enable to periodically connect to the ACS to check for configuration updates. Periodic Inform Interval Specify the amount of time between connections to ACS. Connection Request User Name The username to connect the router from the ACS.
Field Description CPE Certificate Click it to browse and upload the certificate for the router. CA Certificate Click it to browse and upload the CA certificate for the router. 3.5.6 ACL Choose Service > ACL. The page shown in the following figure appears. The following table describes the parameters and buttons of this page: Field Direction Select Description Select the router interface. You can select LAN or WAN. LAN ACL Switch Enable or disable ACL.
Field 3.6 Description Services Allowed You can choose the following services from LAN or WAN: web, telnet, ftp, tftp, snmp, or ping. You can also choose all the services. Add After setting the parameters, click it to add the Current ACL Table. Reset Click it to refresh this page. Advance In the navigation bar, choose Advance. The Advance page that is displayed contains Bridge Setting, Routing, Port Mapping, QoS, SNMP, and Others. 3.6.1 Bridge Setting Choose Advance > Bridge Setting.
Field Description preventing undesirable loops in your network. Apply Changes Click it to save the settings of this page. Undo Click it to refresh this page. Show MACs Click it to show a listing of the learned MAC addresses for the bridge. Click Show MACs. The page shown in the following figure appears. This table shows a list of learned MAC addresses for this bridge. 3.6.2 Routing Choose Advance > Routing. The Routing page that is displayed contains Static Route and RIP. 3.6.2.
The following table describes the parameters and buttons of this page: Field Enable Description Select it to use static IP routes. Destination Enter the IP address of the destination device. Subnet Mask Enter the subnet mask of the destination device. Next Hop Enter the IP address of the next hop in the IP route to the destination device. Metric The metric cost for the destination. Interface The interface for the specified route. Add Route Click it to add the new static route to the table.
Click Show Routes. The table shown in the following figure appears. The table shows a list of destination routes commonly accessed by your network. 3.6.2.2 RIP Click RIP in the left pane. The page shown in the following figure appears. If you are using this device as a RIP-enabled router to communicate with others who is using the Routing Information Protocol (RIP), enable the RIP. This page is used to select the interfaces on your devices that use RIP, and the version of the protocol used.
Field Description Apply Click it to save the settings of this page. Interface The router interface that uses RIP. Recv Version The interface type to accept RIP messages. You can choose RIP1, RIP2, or Both. Choose RIP1 indicates the router receives RIP v1 messages. Choose RIP2 indicates the router receives RIP v2 messages. Choose Both indicates the router receives RIP v1 and RIP v2 messages. Send Version The working mode for sending RIP messages. You can choose RIP1 or RIP2.
The procedure for manipulating a mapping group is as follows: Step 1 Select Enable to enable this function. Step 2 Select a group from the table. Step 3 Select interfaces from the WAN and LAN interface list and add them to the grouped interface list using the arrow buttons to manipulate the required mapping of the ports.
Step 4 Click Apply to save the changes. 3.6.4 QoS Choose Advance > QoS. The page shown in the following figure appears. Entries in this table are used to assign the precedence for each incoming packet based on physical LAN port, TCP/UDP port number, and source/destination IP address/subnet masks. The following table describes the parameters and buttons of this page: Field IP QoS Description You can choose disable or enable.
Field Description is disabled. You need to enable IP QoS, and then you can set the parameters in this page. QoS Policy You can choose stream based, 802.1p based, or DSCP based. Schedule Mode You can choose strict prior or WFQ (4:3:2:1). Src IP The IP address of the source data packet. Src Mask The subnet mask of the source IP address. Src Port The port of the source data packet. Dest IP The IP address of the destination data packet. Dest Mask The subnet mask of the destination IP address.
The following table describes the parameters and buttons of this page: Field Description Enter the IP address of trap host. The trap information is sent to the host. Trap IP Address Community (read-only) name Community (read-write) name 3.6.6 The common character string that is used for obtaining the device information. It is like password, through which SNMP application entry obtains the device information directly. Modify the common character string that is configured by the device.
3.7 Admin In the navigation bar, choose Admin. The Admin page that is displayed contains Commit/Reboot, Upgrade, System Log, Password, and Time Zone. 3.7.1 Commit/Reboot Choose Admin > Commit/Reboot. The page shown in the following figure appears. In this page, you can set the router reset to the default settings or set the router to commit the current settings.
Field Reboot 3.7.2 Description Click it to reboot the router. Upgrade Choose Admin > Upgrade. The Upgrade page that is displayed contains Upgrade Firmware and Backup/Restore. 3.7.2.1 Upgrade Firmware Click Upgrade Firmware in the left pane. The page shown in the following figure appears.In this page, you can upgrade the firmware of the router. I Note: Do not turn off your router or press the Reset button while this procedure is in progress.
3.7.2.2 Backup/Restore Click Backup/Restore. The page shown in the following figure appears. In this page, you can backup the current settings to a file and restore the settings from the file which was saved previously. Note: Do not turn off your router or press the Reset button while these procedures are in progress. The following table describes the parameters and buttons of this page: Field Description Save Settings to File Click it and select the path.
3.7.4 Password Choose Admin > Password. The page shown in the following figure appears. In this page, you can change the password of the user, including admin and user. By default, the super user name and password are admin and admin. The common user name and password are user and user.
The following table describes the parameters of this page: Field Description User Name You can choose admin or user. New Password Enter the password to which you want to change the old password. Confirmed Password Enter the new password again. Set to Default Password After selecting it, the password you set does not take effect. It keeps the default password. 3.7.5 Time Zone Choose Admin > Time Zone. The page shown in the following figure appears.
3.8 Diagnostic In the navigation bar, choose Diagnostic. The Diagnostic page that is displayed contains Ping, ATM Loopback, ADSL and Diagnostic. 3.8.1 Ping Choose Diagnostic > Ping. The page shown in the following figure appears.
The following table describes the parameters and buttons in this page: Field Description Host Enter the IP address. PING Click it to begin to Ping the host address. 3.8.2 ATM Loopback Choose Diagnostic > ATM Loopback. The page shown in the following figure appears. In this page, you can use VCC loopback function to check the connectivity of the VCC. 3.8.3 ADSL Choose Diagnostic > ADSL. The page shown in the following figure appears. It is used for ADSL tone diagnostics.
Click Start to begin ADSL tone diagnostics. 3.8.4 Diagnostic Test Choose Diagnostic > Diagnostic Test. The page shown in the following figure appears. In this page, you can test the DSL connection. Click Run Diagnostic Test to begin testing.
4 4.1 Statement Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
systems, 5 GHz high performance RLAN equipment and 5,8 GHz Broadband Data Transmitting Systems. This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.
4.2 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. 4.3 Part 68 statements This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bass unit of this equipment is a label that contains, among other information, a product identifier in the format US: SGEDL01BGAW95Z97. If requested, this number must be provided to the telephone company.
If you experience trouble with this telephone equipment, please contact the following address and phone number for information on obtaining service or repairs. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs.
