AP699E8.1U10-4 AP Router User manual Ver: 1.
Contents
Chapter 1 Introduction The AP699E8.1U10-4, a Wireless Area Network(WLAN) Access Point supporting 802.11 b/g/n, bringing high-speed wireless Internet connection to a home or office, can provide the transmission of broadband data service. It is suitable for using in a wide range of both residential (in-home) and commercial (offices, apartments, hotels, warehouses) network applications. It gives you a blazing fast connection to the internet, far fast and more convenient. The AP699E8.
Product topology Applications l Home and SOHO wireless gateway l The small enterprise Applications l l l l l l TV over IP (IPTV) Voice over IP (VoIP) Higher data rate broadband sharing Shared broadband internet access Audio and video streaming and transfer PC file and application sharing l Network and online gaming Compliance Certificates l Wi-Fi Certification l FCC Class B l CE Mark Feature l l l l l l l l l l l l l l l l l IEEE802.11 compatible b/g/n draft 2.
l telnet, HTTP Web Management, TFTP for Firmware Upgrade l wireless signal rates: 54, 48, 36, 24, 18, 12, 9, 6 Mb/s for 802.11g; 11, 5.5, 2, 1 Mb/s for 802.11b; 11n (20MHz): MCS0-15 with Short Guard Interval Support (up to 144Mbps )11n (40MHz): MCS0-15 with Short Guard Interval Support (up to 300Mbps ).
The key to maximizing the wireless range is to follow these basic guidelines: n Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise. The location should be away from transformers, heavy-duty motors, fluorescent lights, microwave ovens, refrigerators. n Keep the number of walls and ceilings between the AP and other network devices to a minimum - each wall or ceiling can reduce your AP’s range from 3-90 feet (1-30 meters.
Blinking: sending/receiving data from wireless LAN Off: Transmitter is off LAN Green On: Good Link Blink ing: sending/receiving data from LAN Port Off: No link WPS Green On:WPS Start’ Off:WPS Close Security Green On:Security Start Off:Security Close Attaching an External Antenna This AP comes with an antenna. It is external removable monopole signal-band 2.4 GHz antenna. It can be rotated over 90 degrees and is omni-directional with a gain of less than 2 dBi.
In the following, you will learn how to configure the basic functionsof your wireless AP. Language Configuration The 2880AP support multi-language.After login on the web UI ,You can click open all to choose the Language English or Traditional Chinese from the drop list.And you can choose Status and Statics to view information about the AP.
Operation Mode You may configure the operation mode suitable for you environment.If you select Bridge mode,all ethernet and wireless interfaces are bridged into a single bridge interface.If you select Gateway mode, The first ethernet port is treated as WAN port. The other ethernet ports and the wireless interface are bridged together and are treated as LAN ports.And here, you can set whether NAT enabled. Click Cancel to close without saving, click Apply to save the settings.
Click Cancel to close without saving, click Apply to save the settings. LAN You may enable/disable networking functions and configure their parameters as your wish. Click Cancel to close without saving, click Apply to save the settings.
DHCP Client You could monitor DHCP clients here Wireless Settings Basic Wireless Settings You could configure the minimum number of Wireless settings for communication, such as Network Name (SSID) and Channel. The Access Point can be set simply with only the minimum setting items. Network Mode The 2880AP supports 11a, 11b, 11g, 11a/n mixed mode, 11b/11g mixed mode, 11b/g/n mixed mode.You can configure the suitable network mode. SSID Service Set Identifier.
The Wireless AP supports Multiple SSID which allows it to act as multiple AP appearing in a Wireless LAN network. You can configure up to 7 SSID on the device. BSSID Basic Service Set Identifier. This is the assigned MAC address of the station in the access point. This unique identifier is in Hex format and can only be edited when Multi BSSID is enabled in the previous screen. SSID Broadcast If you want to disable the broadcast of your SSID, you should check the Disable box. It also calls Hide SSID.
HT Physical Mode Click Cancel to clear the settings, click Apply to save the settings. Advaced Wireless Settings Use the Advanced Setup page to make detailed settings for the Wireless. Advanced Setup includes items that are not available from the Basic Setup page, such as Beacon Interval, Control Tx Rates and Basic Data Rates. Basic Data Rate Choose between the following data rates 1, 2, 5.5, 11, 6, 9 , 12, 18, 24, 36, 48,54 and auto. Default is auto.
Click Cancel to close without saving, click Apply to save the settings. Security For example, when you select Security mode, you should config the Radius Sever inforamtion.
Click Cancel to close without saving, click Apply to save the settings. WPS You could setup security easily by choosing PIN or PBC method to do Wi-Fi Protected Setup. Click Apply to save the settings. If you enable WPS, you can view WPS status.
Station list Through this page, you can easily identify the adjacent wireless stations. It will automatically observe the adjacent wireless station’s ID (if specified), MAC address, SSID and current status. Firewall This section mainly introduce some ways to proctect youself through the following configuration.
MAC/IP/Port Filtering You may setup firewall rules to protect your network from virus,worm and malicious activity on the Internet. Select MAC/IP/Port Filtering Enable, click Apply, then you start this function.you may define some rules for the MAC/IP/Port Filtering Settings and apply.It is also very convenient for you to delete these Settings. Port Forwarding This page enables you setup Virtual Servers to provide services on Internet.
Select Virtual Server Settings Enable form drop list, set the IP Address, Port Range, Protocol and comment, click Apple to save the settings, click Reset to clear the data you input and you can easily delete these rules from the Current Virtual Servers list. DMZ This page enables you to setup a De-militarized Zone(DMZ) to separate internal network and Internet.
System Security Settings This page enables you to configure the system firewall to protect AP/Router itself from attacking. Select Allow from drop down list, click Apply to save the setting , click Reset to select Deny. Administration Management You may configure administrator account and password, NTP settings, and Dynamic DNS settings here.
Click Cancel to cancel the settings, click Apply to save the settings. Upgrade Firmware Upgrade the RT2880 firmware to obtain new functionality. It takes about 1 minute to upload flash and be patient please. Caution! A corrupted image will hang up the system. Click Reset to clear the firmware, click Apply to upgrade the firmware.
Settings Management You might save system settings by exporting them to a configuration file, restore them by importing the file, or reset them to factory default. Click Export to export the configuration file and click Import to import the configuration file and click Load Default to reset the settings to factory default. Status The Web interface has been designed to enable you to easily perform advanced configuration tasks and view information about the AP.
Statics The Statics page shows all the statics information about your AP.
System Command This page enable you to run a system command as root Click Apply to run the command you put, click cancel to clear the command you put. System Log This page enables you to look and clear the system log. Click Refresh to refresh the log, click Clear to clear the log.
FCC Notice: This device must not be co-located or operating in conjunction with any other antenna or transmitter NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
