CONTENTS 1.The Repeater System..........................................................................1 2. Installation...........................................................................................3 2.1. Installation Location Requirement....................................................3 2.2. Installation of Outdoor Antenna........................................................3 2.3. Cable Layout and Connector Assembly...........................................6 3.
5.1. Indoor Whip Antenna and Outdoor Yagi/Ldpa Antenna..................12 5.2. Indoor Whip Antenna and Outdoor Tubular Antenna.......................14 5.3. Indoor Panel/Ceiling Antenna and Outdoor Yagi/Panel/ LDPA Antenna.....................................................................16 5.4. Indoor Panel/Ceiling Antenna and Outdoor Tubular Antenna..........18 6.Package Contents............................................ ..................................20 7.About the Booster........................
:.
Cell Phone Signal Solutions Ď Connect to Outdoor Antenna Connect to lndoor Antenna ď Connect to Outdoor Antenna Connect to indoor Antenna Đ Connect to Outdoor Antenna Connect to indoor Antenna đ Connect to Outdoor Antenna Connect to indoor Antenna Ē Connect to Outdoor Antenna Connect to indoor Antenna - 1-2 -
Cell Phone Signal Solutions ē Connect to Outdoor Antenna Connect to lndoor Antenna Ĕ Connect to Outdoor Antenna Connect to indoor Antenna Introduction: The cell phone signal booster antenna kit includes a signal booster, an indoor antenna, an outdoor antenna, coaxial cable, power adapter, English user manual, mounting screw kit.
/49:'22':/54 Cell Phone Signal Solutions The repeaters should be used to cover the indoor area.Humidity and temperature of working environment can affect the reliability of repeater. so, temperature, humidity, dust, interference, power, space requirements and other tactors should be considered during installation of repeater. 2.
Cell Phone Signal Solutions Selecting the installation direction of outdoor antenna. The outdoor antenna should point in the direction of the tower, and it is much better to keep line of sight. Select opposite directions for outdoor antenna and indoor antennas. Please test the signal quality and make sure to avoid self-oscillation first, if have to install Outdoor and Indoor antennas in the same direction. If the directional antenna is selected, the main directional angle should point to the tower antenna.
Cell Phone Signal Solutions If isolation can’t be achieved by the limited distance, the roof of the building or any other barriers can used in between to increase isolattion.
Cell Phone Signal Solutions RTYZGRRGZOUT 5L 5STO JOXKIZOUTGR 'TZKTTG :KYZ ZNK IGRR W[GROZ_ UL 5[ZJUUX GTZKTTG LUX VXULKYYOUTGR OTYZGRRGZOUT ZKGS UTR_ͨ Fix the outdoor antenna after selecting the best position, and adjust height or angles slightly in order to get the best signal with suitable input power level and calling quality. 2.3 Cable layout and connector assembly (1) Keep the type,specifications, routing direction, and curvature radius of cables in compliance with the design requirement.
Cell Phone Signal Solutions (8) Keep exposed Indoor cables in good order. Install pvc troughs if the exposed cables are more than 1 meter long, and put small passive RF parts (such as power splitter) in cable troughs. (9) The steps about how to process the both ends of RF coaxial cables as follows: - Keep the same redundant cable length and keep the length of stripped cables to match the corresponding connectors.
Cell Phone Signal Solutions (2)It is better to use a directional panel antenna when the shape of coverage is long and narrow (corridors, long row of houses in tow sides, tunnels, elevators or rural open space). (3)The small whip antenna is suitable to be installed in small room or apartment.
Cell Phone Signal Solutions 3.1Repeater Installation RTYZGRRGZOUT 9ZKVY :NK 8KVKGZKX YNGRR HK OTYZGRRKJ OT RTJUUX GXKGY UTR_ )UTTKIZ ZNK VU]KX Y[VVR_ GTJ IGHRKY VXUVKXR_ ZU ZNK XKVKGZKXȑY VUXZY )NKIQ GMGOT ZU SGQK Y[XK ZNGZ ZNK XKVKGZKX OY OTYZGRRKJ LOXSR_ GTJ OZY 2+* UT MXKKT *KYIXOVZOUT UL 8KVKGZKXYȑ 6UXZY (1) Outdoor Port: connect with the outdoor antenna by cable. (2) Indoor Port: connect with the indoor antenna by cable (3) DC Port: connect with power supply.
Cell Phone Signal Solutions 'IIKYYUXOKY 9KRKIZOUT Please pay attention to “frequency”and “impedance”during the selection of accessories. All accessories(feeder line, antenna, splitter, combiners, etc.) shall support the repeater’s frequency. For example, the repeater’s frequency is GSM900, all the accessories must support GSM900 frequency; and the repeater’s impedance is 50ohm, the accessories shall all be 50ohm. 9]OZIN UT ZNK VU]KX After power is on, first check the alarm and power LEDS.
Cell Phone Signal Solutions (2) If the signals in small part of the areas have not been improved,please check below: - Check whether the service antenna is installed correctly or not, you may need to move the antenna location to improve coverage. - Check if it is necessary to adjust the direction of the service antenna. -Check whether it is necessary to add one or more antennas to enhance the coverage of special areas.
Cell Phone Signal Solutions 'ZZKTZOUT 1.The signal booster will only work with the correct frequency, so please make sure your phone signal is with the same frequency as the signal booster. 2.This cell phone signal booster will only make a weak signal stronger, it can't create a signal. That means it won't work if the outdoor antenna can't receive any signal. 3.
Cell Phone Signal Solutions 2.Check and find a place where your cell phone could receive the best signal outside your house, then mount the Outdoor Yagi/LDPA Antenna and keep Yagi/LDPA Antenna towards the cell phone signal tower. 3.Tightly connect the 32ft Coaxial Cable to the OUTDOOR port of the Signal Booster. 4.Mount the Signal Booster device somewhere inside the house, the Signal Booster should be mounted in a place where is near from the power socket, and have good ventilation. 5.
Cell Phone Signal Solutions /TJUUX =NOV 'TZKTTG GTJ 5[ZJUUX :[H[RGX 'TZKTTG 1.Tightly connect the 32ft Coaxial Cable to the Outdoor Tubular Antenna. 2. Check and find a place where your cell phone can receive the best signal outside your house, then mount the Outdoor Tubular Antenna. 3. Mount the Signal Booster device somewhere inside the house, the SignalBooster should be mounted in a place where is near from the power socket,and have good ventilation. 4.
Cell Phone Signal Solutions 5. Tightly connect the Indoor Whip Antenna to the INDOOR port of the Signal Booster. 6. Connect the Power Adapter of the Signal Booster and Power Socket.
Cell Phone Signal Solutions /TJUUX 6GTKR )KOROTM 'TZKTTG GTJ 5[ZJUUX ?GMO 6GTKR 2*6' 'TZKTTG 1. Tightly connect the 32ft coaxial cable to the Outdoor Yagi/Panel/LDPA Antenna 2. Check and find a place where your cell phone receives the best signal outside your house, then mount the Outdoor Yagi/Panel/LDPA Antenna the Outdoor Yagi/Panel/LDPA Antenna towards the cell phone signal tower. 3.Mount the Signal Booster device somewhere inside the house.
Cell Phone Signal Solutions 6. Connect the Power Adapter to the Signal Booster and Power Socket.
Cell Phone Signal Solutions /TJUUX 6GTKR )KOROTM 'TZKTTG GTJ 5[ZJUUX :[H[RGX 'TZKTTG 1. Tightly connect the 32ft Coaxial Cable to the Outdoor Tubular Antenna. 2. Check and find a place where your cell phone can receive the best signal outside your house, then mount the Outdoor Tubular Antenna. 3. Mount the Signal Booster device somewhere inside the house, the SignalBooster should be Mounted in a place where is near from the power socket, and have good ventilation. 4.
Cell Phone Signal Solutions Reason 1: There are loose or wrong connections in the repeater system. Solution: Check that the connections between the different parts of the system are hooked up correctly and tightly. Reason 2: The signals of other operators nearby received by outdoor antenna are too strong. ( For example, the other operator’s signals are 10 db stronger than the needed signals ).
Cell Phone Signal Solutions 8KSGXQ Increase the output power*---Recommended ways: adjust the outdoor antenna direction/location, or replace with a higher gain antenna to increase input signal strength. 6GIQGMK )UTZKTZY͵ 1.Signal Booster 2.Indoor Antenna 3.Outdoor Antenna 4.Coaxial Cable 5.Power Adapter 6.User Manual You should receive the Mobile Booster kit which includes the similar above-mentioned fittings.
Cell Phone Signal Solutions 9GLKZ_ 8KSOTJKX =GXTOTM The Federal Communications Commission (FCC) has tested this product and found it to comply with their RF Exposure Requirements, pursuant to FCC Part 22 and 24. To comply with the FCC RF exposure requirements, keep the human user’ s body at least 8” (20cm) from the indoor antenna of the booster. Don’t expose this product to extreme low or high temperature ( -20℃ and 55℃ ).
Cell Phone Signal Solutions a complete list of authorized antennas, cables, and cable loss: -22-23-
Cell Phone Signal Solutions Contact information: Company Name:Shenzhen Fuzhixing Electronics Co., Ltd. Address: 5/F, Block C, Penglongpan Hi-technology Park, Dafu Ind. Z one, Guanlan, Longhua New Dist.