DIVA Quick Start Guide V1.
Contents Product profile Introduction Product Documentation Download FUNSNAP 2 APP 3 3 4 Aircraft Components Intelligent Battery Aircraft Status Indicator Propellers Gimbal and Camera 5 5 8 8 9 Remote Controller Components Charging Powering On / Off Remote Controller Status Indicator Using the Remote Controller Optimal Transmission Range 11 11 12 12 12 14 FUNSNAP 2 APP Activating Device Connecting Device Using Camera Firmware update 15 15 19 19 Flight Flight Environment Requirement Calibration Hover
Appendix Specifications 26 Post-sales Information 28 2
Product profile Introduction Developed by FUNSNAP TechnologyTM, DIVA, the consumer drone has inherited the reliable flight control systems from its predecessor iDol. The system facilitates a smooth flight experience with its excellent position hold and altitude hold capabilities both indoors and outdoors. DIVA’s intelligent battery system gives a flight time of up to 30 minutes. The 13MP high definition camera shoots videos up to 4k (UHD), supporting up to 60 FPS frame rate (only under 1080P).
Download FUNSNAP 2 APP System requirements: iOS 9.0 and above, or Android 5.0 and above.
Aircraft Components Β Α ΐ Ύ Γ Ώ Ε Θ Δ Η Κ Ζ Ι ① Power Button ② Intelligent Battery ③ Battery Level Indicator ④ Gimbal and Camera ⑤ Motors ⑥ Propellers ⑦ Foldable Arms ⑧ Foldable landing Supports ⑨ Front Aircraft Status Indicator (Front LEDs) ⑩ Rear Aircraft Status Indicator (Rear LEDs) Η MicroSD Card Slot Θ MicroUSB Port Ι Sona Sensor Κ Vision Positioning Sensor Intelligent Battery Ύ ① Power Button Ώ ② Battery Level Indicator ③ Charging Slot 5
Powering on / off To turn on/off the intelligent battery, first press the power button once, then press and hold the power button for 3 seconds. Battery level will be displayed through the battery level indicators after the battery is powered on. Checking Battery Level To check the battery level when the battery is off, short press the power button. Then the battery level indicator will display the current battery level.
Connect the power adapter to AC power (110V – 240V, 50 / 60 Hz). Connect the Intelligent battery to the power adapter. When charging is normal, the battery level indicator blinks in cycles. When the battery is fully charged, all battery indicator LEDs will light off. Under normal ambient temperature (15 – 45 degree C), it takes about 45 minutes to fully charge the battery; Under low temperature (10 – 15 degree C) it takes about 90 minutes. Install / Remove Battery 1.
Aircraft Status Indicator Front LEDs Below are the 7 states that can be displayed through the red LEDs at the front of the aircraft: 1 No Wi-Fi connection (connection failure or connection loss) Blinking quickly 2 Low battery voltage Blinking slowly 3 IMU horizontal calibration in progress Blinking quickly 4 Compass calibration Phase 1 Blinking slowly 5 Compass calibration Phase 2 Blinking quickly 6 Confirmation after calibration in all 6 directions Blinking quickly 7 Normal status Solid
The four propellers on DIVA are located at the front left side, front right side, rear left side and rear right side of the main body respectively. The front left propeller and the rear right propeller are clockwise (CW) propellers, while the front right propeller and the rear left propeller are counter-clockwise (CCW) propellers. Marks on the propellers indicate whether it is a CW propeller (labelled with alphabets) or a CCW propeller (labelled with numbers).
Gimbal Operation Precautions When the aircraft is powered on, do not tap or knock the gimbal. Before a flight, deploy the aircraft landing supports and place them on flat surfaces to protect the gimbal. If the aircraft is placed on an uneven surface or on grass, gimbal movements could be obstructed. Huge impacts or collisions could also result in malfunction of the gimbal. Flying amid heavy fog or clouds may result in temporary failure when the gimbal becomes frosted.
Remote Controller Components ΐ Ύ Β Α Ώ Θ Δ Γ ① Power Button ② Battery Level Indicator ③ Status Indicator ④ Return to Home (RTH) Button ⑤ Right Control Stick ⑥ Left Control Stick Ε Ζ Η ⑦ Control Stick Protection Cap ⑧ Mobile Device Clamps ⑨ Take-off / Land Button ⑩ Shutter / Record Button Η Gimbal Dial Θ Antennas Charging To charge the remote controller, connect the controller to the power adapter (5V2A) through a Micro-USB cable.
Powering On / Off To power on/off the remote controller, first press the power button once, then press again and hold the power button for 3 seconds. Remote Controller Status Indicator To check the battery level when the battery is off, short press the power button, then the battery level indicator will display the current battery level.
Mode 1 Left Stick Right Stick Up Turn Left Forward Turn Right Right Left Down Backward Forward Up Mode 2 Left Stick Right Stick Turn Right Turn Left Backward Right Left Down Neutral position: The center position of the stroke of the sticks. Amount of Deflection: The amount of deflection of the control stick with respect to the neutral position. Using mode 1 as an example (nose facing forward): The throttle channel controls aircraft’s altitude.
forward and down to fly backward. The larger the amount of deflection, the faster the aircraft will move forward / backward. If the stick stays in the neutral position, the aircraft will not move forward / backward. The roll channel controls the aircraft’s roll. Move the right stick left to fly left and right to fly right. The larger the deflection amount, the faster the aircraft will move left / right. If the stick stays in the neutral position, the aircraft will not move sideways.
FUNSNAP 2 APP Activating Device The DIVA devices should be activated before use for the first time. To activate the DIVA devices, connect DIVA App to the devices. Upon successful connection, an activation prompt will pop up on the DIVA APP. Follow the onscreen instructions to activate the devices before use. Device not not An inactive device has been detected. Are you sure you want to activate the device? Activated successfully,After that, returns will not be supported.
Flight Screen 1 2 3 4 5 6 7 8 In airGPS STOP 18 14 9 13 17 10 16 11 15 12 1. Back to home screen Tap to go back to home screen. 2. Aircraft status indicator Device not connected Displays flight status and various warning information. 3. Flight parameters խխ Displays aircraft altitude, distance (under GPS mode) and speed. 4. Wi-Fi signal strength խ Displays the Wi-Fi strength between the aircraft and remote controller. 5. GPS status խ Displays the current GPS signal strength.
8. System settings Tap to enter system settings to set geofencing, control stick rates or firmware updates. 9. Shooting modes խ Tap to switch between photo mode and video mode. 10. Shutter / record button խ Tap to start / stop shooting photos or recording videos. 11. Camera settings խ Tap to set ISO, shutter, EV and other parameters under photo mode; set video resolution, filter and other parameters in video mode. 12.
Map screen 4 3 1 2 In airGPS 5 6 7 8 9 1. Mobile device location խ Displays the current location of the mobile device. 2. Aircraft location խ Displays the current location of the aircraft. 3. Waypoint խ The number indicates the sequence of the waypoint. The arrow 1 indicates the heading of the aircraft over that waypoint. To relocate the waypoint, long press and drag it to a desired position. Tap the waypoint to change its heading and altitude. 4. Geofencing խ Displays the area with geofencing.
7. Display mode խ Tap to change the display mode of the map. 8. Add waypoint խ Tap to enter add waypoint mode. Draw lines within geofencing zones to add waypoints. 9. Waypoint tracking խ Tap to enter waypoint tracking after all waypoints are set. Using Camera Camera Mode Three camera modes are available: photo, video and time-lapse. Photo mode and video mode can be selected via the camera mode button on the flight screen. Time-lapse mode can be selected from the camera setting page when in video mode.
Firmware Update Precautions *Ensure the battery levels of the aircraft and the remote controller are both above 50% before updates. *Do not switch off the remote controller / app / aircraft, or operate the remote controller while update is in progress. *A prompt will appear on the APP upon successful firmware update. Follow further instructions on the APP to reboot the device *When updating firmware for the camera, wait for one minute after the APP prompts, then reboot the device.
Flight Flight Environment Requirement Do not fly above grounds that are monochromatic without any textures. Calibration IMU Horizontal Calibration Extend all arms and landing supports. Place the aircraft on a still and level surface. Tap ‘horizontal calibration’ on the APP. The red LEDs will start blinking until calibration is completed. Compass calibration Keep the aircraft away from any metal objects and electrical device, then tap “Compass calibration” on the APP.
Phase 2: When the front LEDs start to blink quickly, keep the aircraft nose pointing upward and rotate the aircraft by 3 turns until the front LEDs become solid. Then the calibration process is complete. *Note: If the front LEDs start to blink slowly during phase 2, it means that the calibration does not pass. Calibration should restart all over. IMU 6-direction calibration Follow the instructions on the app for IMU 6-direction calibration. IMU 6-direction calibration Extend all arms and landing supports.
Adequate lighting and grounds with clearly visible textures are required. B. GPS mode: Enabled when aircraft receives sufficiently strong satellite signal with adequate positional accuracy. The app will give a prompt when the aircraft enters GPS mode, while the aircraft tail light becomes solid. C. Attitude mode: Under poor GPS signal and ground visibility, the aircraft will enter attitude mode. The aircraft will keep itself level, but its position will not be fixed at one point automatically.
Basic flight operations Stick Controls Under optical flow mode, the stick controls the aircraft roll / pitch angle. (The maximum tilt angle is limited to 18 degrees). Under GPS mode, the stick controls the aircraft flight speed. (The maximum flight speed is 10 m/s under sport mode, 4 m /s under normal mode and 2 m/s under tripod mode). Return to Home (RTH) When RTH is triggered, the aircraft will automatically turn its heading towards the home direction and start to fly back.
Follow: the aircraft points its head towards the location of the mobile device and starts following the mobile device with constant position relative to the followed object. Waypoint: the aircraft follows a series of waypoints planned in the APP. Note that when planning the waypoints, obstacles along the waypoints must be avoided. Exiting intelligent flight modes: Tap the exit icon on the APP. Manually move the control sticks to exit (Except orbit mode). When geofence is reached.
Appendix 5FDIOJDBM 4QFDJDBUJPOT Camera Aircraft Sensor 1/3” CMOS Camera Lens FOV: 81.5° Format Equivalent: 28 mm Aperture: f/2.0 Shooting Range: 1.2 m to ∞ Image Size 4000 x 3000 pix Video Recording Modes 4K（UHD 3840 x 2160）/15FPS 2.7K（2704X1520）/30FPS 1080P/30FPS，1080P/60FPS Max Video Bitrate 100Mbps Supported File System FAT32 Photo JPEG Video MP4 APP iOS/Android Weight 430g Size 168*184*64mm Propeller Size 5.
GPS Mode GPS + GLONASS Hovering Accuracy Range Vertical：±0.1m / VIO，±0.5m /GPS Horizontal：±0.1m / VIO，±1.5m /GPS Pitch 0º~ -90º Roll 30º~ -30º Max Control Speed (tilt) 120°/s Capacity 2250mAh Voltage 13.0V Battery Type LiPo 3S Max Charging Voltage 13.05V Energy 27Wh Weight 140 g Charging Temperature Range 10 ~ 45° Max Charging Power 60W Aircraft Gimbal Battery Charger Input 100~240V，50/60HZ Output 13V，3A Video Transmission 5.
*OWFOUPSZ DIVA Drone x1 Remote control x1 Smart battery x1 Propeller (Clockwise x4) &Propeller (anticlockwise x4) Long Joystick x2 Propeller Screw x8 Charger x1 USB x1 6TFS T NBOVBMx1 28
Battery Safety Instructions 29
Read the Battery Safety Instructions carefully before charging the iDol rechargeable lithium polymer battery.Follow the instructions herein strictly. Warning 1. The lithium polymer cells in this battery use volatile materials.Improper use of this battery may cause fire, damage to property or personal injury. 2. The liquid in the battery is highly corrosive. If the battery leaks,do not touch the liquid. If the liquid touches skin or eyes, rinse withwater and seek medical attention immediately. 3.
3. Do not charge the battery close to combustible or flammable materials or liquids. 4. Never leave charging batteries unattended to prevent accidents. 5. If there is a fire, disconnect the chargers power immediately and extinguish the fire following the correct method. 6. The charger has a thermal throttling function, if the battery is within the temperature range of 5 ° C - 40 ° it will charge normally. However, if the battery temperature is outside of this range the battery will not charge.
9.If the battery is submerged in water place it in a safe open area and stay away from it until the battery is air dried. The battery may not be used again and as such and should be discarded. Follow the proper recycling method and local laws & regulations for your district. 10.If the battery catches fire use CO2 (or another electrical safe method) to extinguish the fire. 11.
metal necklaces or other metal objects. 7. Transport the battery within the temperature range of 23 ± 5 ° C. 8. Do not transport damaged batteries. When you need to transport the battery make sure to discharge the battery until it is around 50% capacity. 9. Do not hit, crush or pierce the battery. Do not drop or short-circuit the battery. 10. In hot weather the temperature inside a car will rise quickly.
Disclaimer and Safety Information 34
Disclaimer and Warning The user promises to be responsible for their own behavior and all the consequences arising therefrom. The user will use the product only for legal and legitimate purposes and agrees to the terms and any related policies or guidelines that may be made by Funsnap Technology. While the product adopts advanced technology, inappropriate use of the product could result in personal injury or property damages.
same time, this product complies with the basic requirement’s stipulated in 1999/5/EC and other related directives. It is forbidden to modify or change this product without permission so as to avoid harmful interference being emitted from the product. The manufacture is not responsible for any consequence’s or problems that may arise due to modifications made to this product. 2. It is forbidden to modify or change this product without permission so as not to affect the normal operation of the product. 3.
speeds. When running there is a certain level of danger that must be taken into account. Failure to do so may lead to personal injury or property damage. 3. When using this product, stay away from dangerous environments such as airports, railways, highways, high-rise buildings and suspended wires. 4. When using this product,please stay away from mobile phone base stations,high-power transmission equipment and other high electromagnetic interference environment's. 5.
Warranty Card Product Name User Name Product Serial Number Contact Phone Number Dealer Date of purchase Contact number Maintenance Recordst Repair Date Fault and Repair Conditions The following conditions are not covered by thewarranty: 1. Failure or damage due to transportation, loading and unloading the product after purchase. 2. Any alterations, disassembly, repairs, or repairs not authorized by the manufacturer. 3.
User Notice 1. Data Backup Before you accept this service, please back up all data separately. The company does not take any responsibility for lost or damaged data that may occur. 2. Ownership of parts requiring repair or maintenance Replacement parts or any other parts that are repaired and replaced during the company repair process will be serviced by the company. Parts removed during repair or maintenance shall become property of the company. 3.
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
