User's Manual

ManualsBrandsShenzhen Fudasi Technology ManualsElectronicsPhottix Odin TTL Trigger for Canon

Phottix Odin TTL Trigger for Canon

Parts

Transmitter Control Unit (TCU)

1. LCD Screen

2. Options Button

3. Mode Button

4. Zoom Button

5. Power Button

6. LED

7. + / - / Selection Buttons

8. Test Button

9. Clear Button

10. High Speed Sync / Second Curtain Sync Button

11. LCD Backlight Button

12. USB Port

13. Battery Compartment

14. Locking Ring

15. Hot Shoe

Please Note: After adding turning on the Phottix Odin TCU and receivers you

must take one photograph for the TCU to “learn” about your camera and flashes.

The first shot you take will not be properly exposed. Subsequent images will be

correct.

Slave mode does not need to be set on flashes on Phottix Odin receivers.

Many TTL flashes have been tested but the manufacturer cannot guarantee that

all third party TTL flashes will function properly with the Phottix Odin. It has been

designed and optimized for original Canon flashes using the ETTL II system.

Tip: Turn off all devices – flashes/strobes, cameras, and the Phottix Odin TCU

and receivers - when connecting and disconnecting devices.

Summary of content (6 pages)

PAGE 1
Phottix Odin TTL Trigger for Canon Parts Transmitter Control Unit (TCU) 1. LCD Screen 2. Options Button 3. Mode Button 4. Zoom Button 5. Power Button 6. LED 7. + / - / Selection Buttons 8. Test Button 9. Clear Button 10. High Speed Sync / Second Curtain Sync Button 11. LCD Backlight Button 12. USB Port 13. Battery Compartment 14. Locking Ring 15.
PAGE 2
Upgrading firmware by USB The firmware of the TCU and receivers can be upgraded using the included USB cable. Any upgrades and full instructions will be announced on the Phottix Blog (journal.phottix.com). LED functions The LED on the TCU and receiver units will turn green when the camera is focusing and red when a photo is being taken. Inserting batteries 1. Press the battery cover in while pushing it away from the Phottix Odin TCU or receiver. The battery cover will slide open. 2.
PAGE 3
TTL/Mixed allows groups A, B and C to be set to TTL, Manual or OFF with adjustments to EV or power levels. Ratio is similar to Canon’s native TTL system. The ratio of groups A and B can be set from 8:1 to 1:8. EV levels can also be adjusted. To change function screens: Press the Option button on the TCU. The Option Button will switch between TTL/Mixed and Ratio screens. TTL/Mixed Functions Screen The Selection Button allows you to cycle through groups A, B, and C, and Channel selections.
PAGE 4
Using Zoom: 1. Press the Zoom Button to enter the Zoom screen. 2. Pressing the Selection button will cycle through groups A, B and C, and Transmission channel. 3. Note: Pressing the Selection button after the CH selection will return to the TTL/Mixed or Ratios Function Screens。 4. With groups A, B or C active: Press the Mode Button to change from TTL to Manual mode. In Manual Zoom, press the - / + buttons to adjust the flash zoom. No adjustments can be made in TTL mode. Using the Clear Button: 1.
PAGE 5
Input: USB port (transmitter and receiver) Input voltage: 2.4-3.2V Flash port voltage handling: 6V (transmitter) Body dimensions: 94(L) x 66(W) x 35(H) mm, (transmitter), Antenna: built-in PCB antenna Weight: 105g (transmitter)– without batteries Operating temperature: -15—65 ℃ Storage temperature: -30—85 ℃ * On compatible cameras / flashes Warnings - This product is a precise electronic instrument. Do not expose to damp environments or dust.
PAGE 6
FCC ID: XBYFKT05ZA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.