User Manual

ManualsBrandsShenzhen Four Seas Global Link Network Technology ManualsElectronicsWireless Repeater



UserGuide

WirelessRepeater

M/N:CF‐WR300N

TradeMark:COMFAST

Manufacturer: Shenzhen Four Seas Global Link Network Technology Co., Ltd



1、 ProductSpecification

ThisdeviceasacomplementofwiredLAN(localareanetwork)

achievedthewirelessaccessfunctionofthewiredLANnetwork,

plug‐and‐play.Suitableenvironments:Hotels,School

dormitories,House,Apartments,Buildings

Note:COMF ASTminirepeaterhastwoshape,pleasefind

thecorrespondingdescriptionoftheproduct

according

toyouritemappearance.

WPS/Resetbutton:

WPS/ResetbuttonisatthebottomofThisdevicebesideLAN/WAN

port.Whenpowerison,pressandholdtheWPS/Resetbuttonfor

2seconds,youwillenabletheWPSfunction,pressandholdthe

buttonfor10secondsandrelease,thenitis

restoringthefactory

valuefunctionthedevicewillrestoretofactorysettings.

Warning:

1.Pleaseremovethedeviceifit'sthethunderstormweatherto

keepfromlightningstrikes

2.Keepawayfromheatsourceandkeepventilation.

3.Pleasepayattentiontowaterproofwhenitisinstoring,

transportingandoperatingenvironment.

2、

Introductionof3ApplicationModes

2.1APMode(AccessPoint)

ThisdeviceasacomplementofwiredLAN(LocalArea

Network),achievedthewirelessaccessfunctionofthewiredLAN,

plug‐and‐play.Underthismode,theRJ45wireportisbeingused

asLANport,computercanconnectwithThisdevicethrough

wired

orwirelessway.youhavetosetyourcomputer'sIPaddress

manuallyifyouwanttologinthesettingpage.

2.2RepeaterMode

Summary of content (6 pages)

PAGE 1
User Guide Wireless Repeater M/N: CF‐WR300N Trade Mark: COMFAST Manufacturer: Shenzhen Four Seas Global Link Network Technology Co., Ltd 1、 Product Specification This device as a complement of wired LAN (local area network) achieved the wireless access function of the wired LAN network, plug‐and‐play.
PAGE 2
This device is used for extending the wireless signal's coverage of existing AP or wireless router. Under this mode, the RJ45 wire port is being used as LAN port, computer can connect with this device by wired or wireless signal. You should set your computer's IP address manually or press the reset button for restoration(note: after restoration, it is router mode by default, the computer must through wireless way log in the setting page) Application environments: Duplex houses, Large‐area places. 2.
PAGE 3
4.If your computer's IP address sub net mask and default gateway were set manually, please revise them to "Automatically get the IP address "and" Obtain DNS server address automatically", then click "OK", previous interface also click "OK" 4、 Wireless Network Connection(Win 7 and XP) Windows 7 1.After the installation of the wireless adapter, bottom right corner will appear icon, click this icon. 2.
PAGE 4
(default name is “COMFAST”)an “Pre‐shared key”(note: pre‐shared key is same as the key of the SSID which you want to repeat) 2.Click”connect”,set up waiting for 20 seconds, laptop/mobile phone/pad etc. devices can search out the Repeater ”SSID”, type the key to connect and get the Internet. 8、Wireless router mode 1.Choose"Router" mode as shown below, WAN Access Type default type is "DHCP .Client(dynamic IP)" 2.
PAGE 5
Wi‐Fi function is enabled(we recommend you connect the laptop vendor or read the laptop user manual); B. At device manager interface, check whether the driver of network adapter has been installed successfully; C. Check whether the wifi service has been turned on, right click the icon" my computer" on your desktop, choose manage. In "Computer Management" wizard, click"Services and A applications",then on the page of "Service", find the item "Wireless Zero Configuration" and check its Status value. D.
PAGE 6
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only mobile configurations.