User Manual Model: FI9805E
www.foscam.com Table of Contents 1 Overviews ................................................................................................................................................ 3 1.1 Key Features .......................................................................................................................................................3 1.2 PoE (Power over Ethernet) .......................................................................................................................
www.foscam.com 3.7.2 RS485 configuration...................................................................................................................................50 3.8 Path Settings .....................................................................................................................................................51 3.9 Firewall ...........................................................................................................................................................
www.foscam.com 1 Overviews FOSCAM FI9805E is an integrated PoE Network Camera solution with a color CMOS sensor enabling viewing resolution 1280*720. It combines a high quality digital video camera, with a powerful web server, to bring clear video to your desktop from anywhere on your local network or over the Internet. FI9805E supports the industry-standard H.264 compression technology, drastically reducing file sizes and conserving valuable network bandwidth.
www.foscam.com Multi-level users management with password protection Motion detection alert via email or upload image to FTP Supports Third Party Domain name Supports multiple network protocols: HTTP /TCP /IP /UDP /FTP /DHCP /DDNS / UPNP Providing Phone APPs for Android and iPhone users 1.2 PoE (Power over Ethernet) The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable.
www.foscam.com 1.4 Packing Contents ● IPCAM×1 ● CD×1 ● DC Power Supply×1 ● Warranty Card×1 ● Mounting bracket×1(option) ● Network Cable×1 1.5 Physical Description Front Panel 1 2 Figure 1.1 1 LENS: CMOS sensor with fixed focus lens 2 Infrared LED: 36 IR LEDs Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Interface 1 2 3 4 5 6 7 Figure 1.2 1) I/O alarm terminal block This network camera provides a I/O alarm terminal block which is used to connect to external input / output device. The pin(there are four number in the terminal block from no. 1 to no. 4) definitions are descripted below: 1– input 2- input 3- output 4- output This camera supports I/O alarm, you can go to Settings – Alarm – I/O page to configure it. 2)LAN 10/100M adaptive Ethernet interface.
www.foscam.com 3) Reset button Press and hold on the reset button for 5 seconds. Releasing the reset button, the password will back to the factory default administrator password. The default administrator user is admin with no password. 4)Power Interface Connect the external power adapter, request for 12V/2A power. 5) Audio input interface: The jack is used to plug external input device such as sound pick up device directly.
www.foscam.com 2 Surveillance Software GUI Please refer to the Quick Installation Guide if you install the camera at first time. After finishing quick installation, you can take time to learn the operation of the software. 2.1 Login Window 1 2 3 4 Figure 2.1 Please check the login window above, it was divided to 54sections from no. 1 to 4.
www.foscam.com Section3 Select the language You can select the language you need via click on the language dropdown list to switch. Section4 Login the camera Click Login button and you will see the surveillance windows. Figure 2.2 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 2.2 Surveillance Window 1 2 8 3 4 5 6 7 Figure 2.3 Section1 9 FOSCAM Logo/ LiveVideo / Settings buttons : : FOSCAM LOGO Path to surveillance window. Click this button and back to the surveillance window : Path to Administrator Control Panel, Click it and it will lead to Administrator Control Panel and do advanced settings. Section2 Multi-Device Window The firmware inside the camera supports up to maximum of 9 cameras being monitoring at the same time.
www.foscam.com Figure 2.4 Section3 Mode/ Stream / Mirror/ Flip buttons Mode 1) 50HZ ---------Indoor surveillance (Region: Europe, China) 2) 60HZ ---------Indoor surveillance (Region: USA, Canada) 3) Outdoor-------Outdoor surveillance (Region: All over the world) There are three options within the menu of Mode: 50HZ, 60HZ and Outdoor. It depends on the frequency of the electricity and surveillance model (indoors & outdoor). Please choose outdoor mode, when the camera was installed outside.
www.foscam.com 3) Maximum frame rate When the video format is 50Hz, the maximum frame rate is 25 fps. When the video format is 60Hz, the maximum frame rate is 30 fps. You should lower frame rate when the bandwidth is limited. Normally, when the frame rate above 15, you can achieve fluently video. 4) Bit rate Generally speaking, the larger the bit rate is, the clearer video will become. But the bit rate configuration should combine well with the network bandwidth.
www.foscam.com Section5 Cruise Here only support two cruise tracks: Vertical and Horizontal. Vertical: The camera will rotate from up to down. Horizontal: The camera will rotate from left to right. : Start cruise. : Stop cruise. How to do cruise? Firstly: Select one track in the track dropdown list Secondly: Thirdly: Section6 Click Start cruise button, the camera will cruise following the predefined path. Click stop button and finish cruising.
www.foscam.com Section7 Image quality settings In this page, you can tune Hue, Brightness, Contrast, Saturation, and Sharpness to get higher quality. Section8 OSD( On screen display) If you have added time and camera name in the video, you can see it in the live window. Go to Settings ---Basic settings---Camera name panel, and you can change another device name. The default device name is anonymous. Go to Settings ---Basic settings---Camera time panel and adjust the device time.
www.foscam.com 5----- Snap: Click it to make snapshot and it pop up a window which picture you snapshot, right click in the window and save the picture to anywhere you want. 6----- Record: Click the icon and the camera start recording, you can see a green dot in the live window. Click again and stop recording. The default storage path is C:\IPCamRecord. You can change the storage path: Go to Settings- >Record-> Storage Location panel.
www.foscam.com Figure 2.7 Full Screen: Select it and Click it to make full-screen, press ESC and exit full-screen. Zoom up/down: Click it and the live view will be digital zoomed up, then click Zoom Down and the live view back to original size. Figure 2.8 NOTE: 1 Please make sure the camera has connected with outer cradle head and configured RS485 protocol successfully, or else Screen PTZ doesn’t work. 2 For Mac OS, the plugin cannot support Onscreen Mouse function, so you cannot allow to use it.
www.foscam.com 3 Advanced Camera Settings Click the button “Settings”, goes to Administrator Control Panel to make advanced camera settings. 3.1 Device Status Device Status contains four columns: Device Information, Device Status, Session Status and Log, it will show you various information about your camera. 3.1.1 Device Information Figure 3.1 Camera name: The Device Name is a unique name that you can give to your device to help you identify it.
www.foscam.com 3.1.2 Device Status On this page you can see device status such as Alarm status, NTP/DDNS status, WIFI status and so on. Figure 3.2 3.1.3 Session status Session status will display who and which IP is visiting the camera now. Figure 3.3 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 3.1.4 Log The log record shows who and which IP address accessed or logout the camera and when. Click the page number and go to the corresponding page to see more logs Fill in one page number, click Go button and go to the corresponding page Figure 3.4 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 3.2 Basic Settings This section allows you to configure your Camera Name, Camera Time, Mail, User Accounts and Multi-Device. 3.2.1 Camera Name Default alias is Anonymous. You can define a name for your camera here such as apple. Click Save to save your changes. The alias name cannot contain special characters. Figure 3.5 3.2.2 Camera Time This section allows you to configure the settings of the internal system clocks for your camera. Figure 3.
www.foscam.com time format. Click Save button to submit your settings. 3.2.3 Mail Settings If you want the camera to send emails when motion has been detected, here Mail will need to be configured. 5 1 2 6 3 4 Figure 3.7 1----- SMTP Server/ Port /Transport Layer Security Enter SMTP server for sender. SMTP port is usually set as 25. Some SMTP servers have their own port, such as 587 or 465, and Transport Layer Security usually is None.
www.foscam.com Test result Figure 3.8 If the test success, you can see the Success behind the Test, at the same time the receivers will receive a test mail. Figure 3.9 If the test fails with one of the following errors after clicking Test, verify that the information you entered is correct and again select Test . 1) Cannot connect to the server 2) Network Error. Please try later 3) Server Error Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 4) Incorrect user or password 5) The sender is denied by the server. Maybe the server need to authenticate the user, please check it and try again 6) The receiver is denied by the server. Maybe because of the anti-spam privacy of the server 7) The message is denied by the server. Maybe because of the anti-spam privacy of the server 8) The server does not support the authentication mode used by the device 3.2.
www.foscam.com Figure 3.11 How to add account ? Select one blank column, then enter the new user name, password and privilege, last click Add to take effect. You can see the new added account on the Account list. Figure 3.12 Figure 3.13 Delete Select the account which you want to delete, then click Delete button to take effect. Note: The default administrator account cannot be deleted, but you can add other administrator users. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 3.2.5 Multi-Camera If you want to view multi-surveillance screens on one window, you need to login one camera, and set it as the main device, and do Multi-Device Settings, add other cameras to the first one camera. Before you do multi-cams settings, you need to assign different port such as 81, 82, 83, 84, 85, 86, 87, 88 to the cameras if there is 8 cams installed. The firmware within the camera can support a maximum of 9 devices monitoring all at the same time.
www.foscam.com Camera Model: Our Company produces two series cameras: MJPEG and H.264. Figure 3.15 Back to Surveillance Windows, and click Four Windows option, you will see four cameras you added. Figure 3.16 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 3.17 Add cameras in WAN If you want to view all cameras via the internet(remote computer), you will need to add them using DDNS domain name. Firstly, make sure all of the cameras you added can be accessed through the internet. (Read How to configure DDNS settings in chapter 3.3.3) Login to the first camera using a DDNS domain name and port. Use DDNS domain name and port to login Make sure each camera you need add could login with DDNS name and port Figure 3.
www.foscam.com Click Multi-Device Settings. Choose The 2nd Device. Fill in the 2nd camera’s name, DDNS domain name, port number. Enter user name and password and then choose Add. (Figure 3.19) 1 2 3 4 5 Figure 3.19 1----- The camera model: MJ or H264. 2----- The 2nd camera’s name 3----- Fill in the 2nd camera’s DDNS host not LAN IP.
www.foscam.com Figure 3.20 Return to video window. You will see all of the cameras accessible through the internet. When you are away from home, you can use the first camera’s DDNS domain name and port to view all the cameras via internet. Figure 3.21 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 3.3 Network This section will allow you to configure your camera’s IP, PPPoE, DDNS, UPnP and Port. 3.3.1 IP Configuration If you want to set a static IP for the camera, please go to IP Configuration page. Keep the camera in the same subnet of your router or computer. Figure 3.22 Changing settings here is the same as using the IP Camera Tool. (Figure 3.23/3.24) It is recommended that you use the subnet mask, gateway and DNS server from your locally attached PC.
www.foscam.com Figure 3.23 Figure 3.24 If you don’t know the DNS server, you can use the same settings as the Default Gateway. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 3.3.2 PPPoE If you are using a PPPoE connection, enable it and enter the User Name and Password for your PPPoE account. Figure 3.25 3.3.3 DDNS FOSCAM camera has embedded a unique DDNS domain name when producing, and you can directly use the domain name, you can also use the third party domain name. FOSCAM domain name Here take test09.myfoscam.org for example. Go to option of DDNS on the Settings->Network panel, you can see the domain name. Figure 3.
www.foscam.com Third Party Domain Name Settings User can also use third part DDNS, such as www.no-ip.com. ,www. 3322.com Here take www.no-ip.com for example: ① Step 1, Go to the website www.no-ip.com to create a free hostname Firstly: Login on www.no-ip.com and click No-IP Free to register. Click here to register Figure 3.27 Please register an account step by step according to instructions on www.no-ip.com After registration, please login your email which used to register.
www.foscam.com Figure 3.28 Figure 3.29 Please create the domain name step by step according to instructions on www.no-ip.com Step 2, DO DDNS Service Settings within the Camera Please set DDNS Settings within the camera by hostname, a user name and password you’ve got from www.no-ip.com Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Take hostname ycxgwp.no-ip.info, user name foscam, password foscam2012 for example. Firstly, goes to option of DDNS Settings on the administrator panel. Secondly, select No-Ip as a server.. Thirdly, fill foscam as DDNS user, fill password foscam2012 as DDNS password, fill ycxgwp.no-ip.info as DDNS domain and server URL, Then click save to make effect. The camera will restart and to take the DDNS settings effective.
www.foscam.com Figure 3.30 ③ Use domain name to access the camera via internet After the port forwarding is finished, you can use the domain name+ http no. to access the camera via internet. Take hostname ycxgwp.no-ip.info and http no. 2000for example, the accessing link of the camera via internet would be http:// ycxgwp.no-ip.info:2000 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 3.3.4 UPnP Figure 3.31 The default UPnP status is closed. You can enable UPnP, then the camera’s software will be configured for port forwarding. Back to the “Device Status” panel, you can see the UPnP status: Figure 3.32 The camera’s software will be configured for port forwarding. There may be issues with your routers security settings, and sometimes may error. We recommend you configure port forwarding manually on your router (Figure 3.30). 3.3.
www.foscam.com Figure 3.33 HTTPS port: The default port is 443. You can use the url to access the camera: https:// IP + HTTPS port. Sometimes you need to add the url to the Trusted Sites, Open Internet Explorer if it is not already opened. Click on Tools, then click Internet Options. Next, click the Security tab, then click the Trusted sites button. Figure 3.34 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Another way to change the HTTP port no. Step 1: Open the IP Camera Tool, select the camera you would like to change the port of, right click on the IP address, and click on ”Network Configuration”, this brings up the network configuration box as shown in Figure 3.35 and 3.36. Select which camera you’d like to change the port for, and right click Figure 3.35 Modify the Http Port. Enter the Username and password, click OK. Figure 3.
www.foscam.com have problems later with remote access and seeing the camera remotely if the camera loses power and reconnects on a different LAN IP address. Make sure you set a static LAN IP address! Note: If the camera cannot be accessed, please make sure the port forwarding is succeed. 3.4 Video This section allows you to configure Video stream settings, On screen display and Snapshot settings. 3.4.1 Settings Figure 3.37 Stream type: There are four types to identify different streams you have set.
www.foscam.com narrow, and bit rate is large, that will lead to video can not play well. Frame rate: Note that a larger frame size takes up more bandwidth. When the video format is 50Hz, the maximum frame rate is 25 fps. When the video format is 60Hz, the maximum frame rate is 30 fps. You should lower frame rate when the bandwidth is limited. Normally, when the frame rate above 15, you can achieve fluently video. Key Frame Interval: The time between last key frame and next key frame.
www.foscam.com The mask area Figure 3.39 Click Back button and return to the OSD page, click Save to take effect. Back to the surveillance window, you can see the mask area as the following picture: Figure 3.40 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 3.4.3 Snapshot Settings On this page you can set the snapshot pictures’ image quality and the storage path. Figure 3.41 Image Quality: Low, Middle and High. The higher the quality, the picture will be clearer. Save Path: FTP. If you have done FTP and Alarm settings, when alarming, the camera will snap pictures to the FTP automatically. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 3.5 Alarm IP Camera supports Motion Detection Alarm and I/O alarm, when the motion has been detected, it will send emails, upload images to FTP or adopt other output action. 3.5.1 Motion Detection 7 1 2 3 4 5 6 Figure 3.42 To enable motion detection, follow the steps below: 1 Enable Motion detection 2 Sensitivity---- It supports three modes: Low, Middle and High. The higher the sensitivity, the camera will be more easily alarmed. Select one motion sensitivity.
www.foscam.com There are four alarm indicators: A Ring If the camera has connected with a speaker or other audio output device, then you select Ring, when the motion has been detected, the people around the camera will hear beep alarm sound. B Send E-mail If you want to receive alarm emails when motion is detected, you must select Send Mail and set Mail Settings first. The alarm email cannot contain the alarm picture if you have not selected Snap picture.
www.foscam.com Figure 3.43 6 Alarm Schedule ① Alarm anytime when motion is detected Click the black button up the MON, you will see all time range turn red. When something moving in the detection area at anytime, the camera will alarm. Click this button and select all time range Figure 3.44 ② Specify an alarm schedule Click the week day words, the corresponding column will be selected. For example, click TUE, Shenzhen Foscam Intelligent Technology Co.
www.foscam.com the all column of TUE turns to red, that means during Tuesday whole day, when something moving in the detection area, the camera will alarm. Figure 3.45 ③ Press the left mouse and drag it on the time boxes, you can select the serial area, Figure 3.46 7 Click Save button to take effect. When the motion is detected during the detection time in the detection area, the camera will alarm and adopt the corresponding alarm indicators.
www.foscam.com 3.5.2 I/O Detection This camera supports I/O terminal block which is used to connected external input/output device. After connection successfully, you can go to this page and do I/O alarm configuration. 7 1 2 3 4 5 6 To enable motion detection, follow the steps below: 1 Enable Motion detection 2 Sensitivity---- It supports three modes: Low, Middle and High. The higher the sensitivity, the camera will be more easily alarmed. Select one motion sensitivity.
www.foscam.com B Send E-mail If you want to receive alarm emails when motion is detected, you must select Send Mail and set Mail Settings first. The alarm email cannot contain the alarm picture if you have not selected Snap picture. C Take Snapshot If you select this checkbox, when the motion has been detected, the camera will snap the live view window as a still picture and load it to the FTP. If you select Send Email, at the same time the picture will be send to you as an attachment.
www.foscam.com 3.6 Record On this page you can change the manually recording storage path, the default storage path is C:\IPCamRecord. Figure 3.47 3.7 PTZ This page will allow you to change the pan/tilt speed and the RS485 protocol configuration. 3.7.1 Pan/Tilt Speed There are five Pt speed types: very fast, fast, normal, slow and very slowly. Select the desired PTZ speed type and click save button . Figure 3.48 3.7.
www.foscam.com Figure 3.49 3.8 Path Settings If you want to upload record images to your FTP server,you can set FTP Settings. Figure 3.50 Figure 3.51 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com FTP server: If your FTP server is located on the LAN, you can set as Figure 3.50. If you have an FTP server which you can access on the internet, you can set as Figure 3.51. Port: Default is port 21. If changed, external FTP client program must change the server connection port accordingly. FTP Mode: Here supports two modes: PORT and PASV. Username/password: The FTP account and password. Click Save to take effect. Click Test to see if FTP has been successfully configured.
www.foscam.com 3.9 Firewall This section explains how to control the access permission by checking the client PC’s IP addresses. It is composed of the following columns: Block access from these IP addresses and Only allow access from these IP addresses. Figure 3.52 Enable firewall, If you select Only allow access from these IP addresses and fill in 8 IP addresses at most, only those clients whose IP addresses listed in the Only allow access from these IP addresses can access the Network Camera.
www.foscam.com 3.10 System In this panel, you can back up/restore your camera settings, upgrade the firmware to the latest version, restore the camera to default settings and reboot the device. 3.10.1 Back up& Restore settings Click Backup to save all the parameters you have set. These parameters will be stored in a bin file for future use. Click Browse and select the parameters file you have stored, then click Submit to restore the restore the parameters. Figure 3.53 3.10.
www.foscam.com Upgrade Firmware by IP Camera Tool Double click the IP Camera Tool shot icon , select the Camera IP that you want to upgrade the firmware. Then select Upgrade Firmware and enter the username and password, choose the firmware file, and upgrade. Figure 3.55 Enter the User name and password Figure 3.56 CAUTION: If your camera works well with the current firmware, we recommend not upgrading. Please don’t upgrade the firmware unnecessarily.
www.foscam.com upgrading. Read the upgrade documentation (readme.txt file) in the upgrade package before you upgrade. 3) Upon downloading the firmware check the sizes of the .bin files. They must match the size in the readme.txt file. If not, please download the firmware again until the sizes are the same. Your camera will not function correctly if a corrupt .bin file is used. 4) Normally, only Device WEB UI need to be upgrade, please do not try to upgrade the Device Firmware.
www.foscam.com 4 Phone APPs With Phone APPs , you can view your camera directly as a computer anywhere, anytime. This section shows the user how to set up the iPhone, and Android mobile phones to view Foscam cameras with Phone APPs. 4.1 APP for Android cell phones There are two ways to install the phone App : 1) Search the APP “Foscam ip cam viewer” in the Google Play directly if your cell phone has installed Google Play. Figure 4.
www.foscam.com Click the shortcut icon and login Phone APP. Default user name is admin with a blank password Figure 4.2 Enter the user name and password then click Login button, you can see the following surveillance windows: 1 2 3 Figure 4.3 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com The default surveillance window is black, you need to add devices to it and then connect the device. Please check the login window above, it was divided to 3 sections from no. 1 to 3.
www.foscam.com How to add cameras to the Phone APP The following steps are required before adding cameras to the APP: 1) Install the IP Camera(s) which wants to be monitored. 2) Login the IP Camera(s) by web browser and set the IP address, port, username & password and make sure the camera can be accessed by browsers. 3) DDNS setting is a plus whenever you want to add the devices by WAN. Click the button and go to Device List page, this section will show you how to add cameras in LAN or in WAN.
www.foscam.com Section3 Add device buttons Add device in LAN : Click this icon and the APP will search all cameras in LAN automatically. Such as the following screen: Figure 4.5 Select the camera IP and click OK to add cameras in LAN, then you can see the camera in the Device List. Add device through scanning UID (User Identification) number : UID Scan. Click this icon and scan the UID no. in the camera body, then the camera can be added to the App. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 4.6 Normally each camera has one unique UID and UID is used for PnP function. Now our camera does not support UID number, so here you cannot allow to use UID to add device. Add device in WAN : Click this icon and you can add cameras in WAN manually. Click this icon and it pops up the following screen, here you can add cameras manually. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 4.7 Camera Type: Our Company produces two series cameras: MJ and H.264. Here select the camera type that you want to add. Camera name: The Camera name is a unique name that you can give to your device to help you identify it. IP address: Fill in the camera’s DDNS host or WAN IP not LAN IP. Stream type: It has two types: Main stream and Sub stream. For cell phones, we recommend you to select Sub stream to get more fluent video.
www.foscam.com Click the icon to add camera then you can see the camera in the Device List. . Select one IP address and click it, then you can enter the surveillance window. Select one IP address in the Device List and press it for a moment, it pop up the following screen: Figure 4.8 Edit: Re- edit the camera’s information, such as the Http / Media port, user name and password, and so on. Click Edit and you can go to Add camera page (Figure 4.7). Delete device: Delete the camera from the Device List.
www.foscam.com 4.2 APP for iPhones If you use iPhone, please search the APP “Foscam ip cam viewer” and install it through APP Store, then you can see the shortcut icon in your cell phone screen. Click the icon and you can go to “ipcam table” page directly: 1 Figure 4.9 2 The default device list is null, you need to add cameras to it. Section1 Camera list Here will list all cameras that added to the software.
www.foscam.com WAN to the software. How to add cameras to the APP The following steps are required before adding cameras to the App: 1) Install the IP Camera(s) which wants to be monitored. 2) Login the IP Camera(s) by web browser and set the IP address, port, username & password and make sure the camera can be accessed by browsers. 3) DDNS setting is a plus whenever you want to add the devices by WAN. If you want to add cameras to the App, please click this icon go to “add ipcam” page(Figure 4.10).
www.foscam.com Add device in LAN Click this button and the APP will search all cameras in LAN, then add it to APP automatically . The cameras in LAN can be searched and added to APP automatically Figure 4.11 There is a icon after the camera name, click it and you can enter the user name, password and web port to login the camera. Figure 4.12 Add device in WAN Step 1: Click the Add Camera icon to add cameras manually. Step 2: Select the camera type: mjpeg or h.284 (Figure 4.
www.foscam.com Figure 4.14a Add H.264 Device Page Figure 4.14b Add MJPEG Device Page UID: If your camera supports UID, here you scan UID number. Now FOSCAM camera does not support UID. Device name: The Device name is a unique name that you can give to your device to help you identify it. IP address: Fill in the camera’s DDNS host or WAN IP not LAN IP. User &Password: The camera’s user name and password. Media / Web port: For MJPEG cameras, here only support web port.
www.foscam.com Stream type: It has two types: Main stream and Sub stream. For cell phones, we recommend you to select Sub stream to get more fluent video. Step 3: Click Add button to add cameras, then you can see the camera name in the “ip cam table” page. Figure 4.15 Surveillance windows Back to “ipcam table” page and you can see all cameras that have added. There is a icon after one camera name, click this icon and you can alter the camera’s user name, password, media port and http port. Figure 4.
www.foscam.com Figure 4.17 Click one camera ip and you can see the live video. 1 2 3 4 Figure 4.18 Please check the login window above, it was divided to 4 sections from no. 1 to 4. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Section1 Back Button : Click this icon and back to “ipcam table” page. Section2 Photo Button Click this icon and look the photos you have captured. Section3 Live view window If the camera supports PT function, here slide on the screen with your finger, the camera will rotate follow your finger direction. Section4 Snapshot/Audio/Talk buttons Talk Audio Snapshot Snapshot Click it to make snapshot. Audio button Click it and you will hear sound captured by the camera’s built-in microphone.
www.foscam.com 5 APPENDIX 5.1 Frequently Asked Questions NOTE: Any questions you would meet, please check Network connections firstly. Check the working status revealed by the indicators on the network server, hub, exchange and network card. If abnormal, check the network connections. 5.1.1 How to download and installl the ActiveX for Firefox users For the first time login the camera, it may prompt you to download plugin. Click here to download the plugin Figure 5.
www.foscam.com Click Install Now Figure 5.2 Reboot the Firefox after the plugin installation is successfully completely, then re-login the camera again, you can see the surveillance window NOTE: If you could not view living video after running the ActiveX, only a red cross in the center of the video or just a black screen. Please change another port number to try. Make sure all firewall or antivirus software on your computer does not block the active download and installation.
www.foscam.com . Figure 5.3 Download the plugin and drag it to the Extensions page of Google Chrome. Click Add button to install the plugin Figure5.4 Click Add button to install the Plugins. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Click Add button to install the plugin Figure 5.5 Reboot the browser and re-login the camera, you will see the surveillance window. 5.1.3 I have forgotten the administrator password To reset the administrator password, you had better unplug the network cable firstly. After that, press and hold down the RESET BUTTON about 5 seconds. Releasing the reset button, the password will turn to the factory default. Default administrator username/password: admin with blank password 5.1.
www.foscam.com 5.1.5 Camera can not record when I click Record button or I can’t change the manually record path When you use Windows7 or Vista, you may be not able to do manually record or change the record path because of the security settings of computer. There are two ways to resolve this problem: (1) Please add the camera as a trusted site to resolve this issue.
www.foscam.com Figure 5.6 If you allow the ActiveX running, but still could not see living video. Please change another port number to try. Don’t use port 8000. Figure5.7 NOTE: Make sure that your firewall or anti-virus software does not block the camera or ActiveX. If you could not see video, please shut down firewall or anti-virus software to try again. 5.1.
www.foscam.com 5.2 Default Parameters Default network Parameters IP address: obtain dynamically Subnet mask: obtain dynamically Gateway: obtain dynamically DDNS: Embedded FOSCAM DDNS Service Username and password Default administrator username: admin Default administrator password: No password 5.3 Specification Specification Image Sensor Lens Audio Video Network FI9805E Image Sensor High Definition Color CMOS Sensor Lens f : 4mm or 6mm or 8mm Mini. Illumination 0.
www.foscam.com Alarm Alarm detection The motion detecting 、 I/O alarm Alarm inform Support Email、FTP、I/O output alarm etc alarm inform way POWER Interface Hardware Interface Audio Interface DC 12V/2.0A (EU,US,AU adapter or other types option, Power Consumption ﹤8 Watts Input/Output One audio input jack, One audio output jack.
www.foscam.com 6 OBTAINING TECHNICAL SUPPORT While we hope your experience with the IPCAM network camera is enjoyable and easy to use, you may experience some issues or have questions that this User’s Guide has not answered. If you have problem with FOSCAM IP camera, please first contact FOSCAM reseller for solving the problems. If our reseller cannot provide service, please contact our service department: tech@foscam.com .
www.foscam.com Shenzhen Foscam Intelligent Technology Co.