Wireless Air Quality Monitor with Indoor Temperature and Humidity Model: WH0290
Contents 1. Introduction...........................................................2 2. Get Started........................................................... 2 2.1 Parts List....................................................2 2.2 Air Quality Sensor Set Up........................3 2.3 Display Console Set Up...........................5 2.3.1 Display Console Layout................7 3. Wireless Sensor Installation.............................. 8 4. Console Operation...........................................
1. Introduction Thanks for your purchasing of the WH0290 Wireless Air Quality Monitor with Indoor Temperature and Humidity. To ensure the best product performance, please read this manual and retain it for future reference. 2. Get Started Note: Power up sequence can be performed in the order shown in this section (insert batteries in the Air Quality Monitor first, then Sensor(transmitter).
5 Two LSD( low self discharge) Ni-MH Rechargeable Batteries 2.2 Air Quality Sensor Set Up 1.
1 2 3 4 5 6 Solar panel Battery Compartment Cover Red LED Indicator (RF transmission) Blue LED Indicator (charging status) USB Port Battery Compartment 2. Insert two AA battery. 3. After inserting the battery, the remote sensor LED indicator will light for 4 seconds, and then flash once per 10 minutes thereafter. Each time it flashes, the sensor is transmitting data. 4.
2.3 Display Console Set Up 1. 2. Move the remote about 2 to 3m away from the display console (if the sensor is too close, it may not be received by the display console). Remove the battery door on the back of the display, as shown in Figure 2. Insert one AA (alkaline, lithium or rechargeable) battery in the back of the display console. Figure 2 1. Integrated Hanging Hole 2. Tabletop Stand 3. °C/°F Button 4. MAX Button 5. Battery Compartment 6.
All of the LCD segments will light up for a few seconds to verify all segments are operating properly. Full Display Replace the battery door, and fold out the desk stand and place the console in the upright position. The console will instantly display indoor temperature and humidity. The PM 2.5 value will update on the display within a few minutes. While in the search mode, the reception search icon flash. If the remote does not update, please contact our Customer Service for support. 3.
2.3.1 Display Console Layout Figure 3 1. 2. 3. 4. 5. 6. 7. 8. Current PM2.5 Concentration Air Quality Level Current AQI Indoor Temperature Indoor Humidity 1h Max AQI 1h Max PM2.
3. Wireless Sensor Installation Outdoor Installation Use four screws to fix the base of the outdoor sensor on a flat surface.
4. Console Operation Note: The console has two buttons for easy operation: 【 °C/°F 】 button (on the left), and 【MAX】button (on the right). 4.1 °C/°F Short press【°C/°F】button: switch between display of temperature unit: °C/°F Press and hold the 【 ° C/ ° F 】 button for 2 seconds: switch between display of the 24H average value of the PM2.5 concentration and AQI. 4.2 MAX Short press the【MAX】button: switch between display of the 1h MAX / 24h MAX / MAX(since last reset) value of the PM2.
5. Sensor Resynchronization When the remote sensor lost reception, holding the °C/°F and MAX button for 5s, will register new outdoor for 12 minutes. While in the search mode, the reception search icon flash. You can also re-sync the two units by removing all the batteries and then wait for several minutes. Then install the batteries again to register faster. 6. Best Practices for Wireless Communication Note: To insure proper communication, place the remote sensor on a flat surface.
7. Function 1)Indoor temperature and humidity 2)Every 60 second the unit will measure indoor temperature and humidity. 3)Display current / 24H average PM 2.5 concentration and AQI. 4)Display 1h MAX / 24h MAX / MAX (since last reset) PM 2.5 concentration and AQI. 5)Air quality level indicator color bar based on AQI. 6)IPx4 rainproof sensor, can be used both indoor and outdoor.
8. Appendix About the Air Quality Levels AQI 0 - 50 51 -100 101-150 151-200 Air Pollution Level PM2.5 Concentration ug/m3 Good 0.0-12.0 Moderate Poor Unhealthy 12.1-35.4 35.5-55.4 55.5-150.4 201-300 Severe 150.5-250.4 300+ Hazardous 250.
9. Specifications 9.1 Wireless Specifications Line of sight wireless transmission (in open air): 300feet(100meters) Frequency: 433/915/868 MHz (optional) Update Rate: 10 minutes 9.2 Measurement Specifications The following table provides specifications for the measured parameters. Measurement Range Accuracy Resolution Indoor 14 to 140 °F ± 1 °F 0.1 °F temperature (-10 to 60°C) (±1°C) (±0.5°C) Indoor 1 to 99 % Accuracy +/- 3% RH 1% Humidity (@25°C. , 30%RH to 80%RH).
9.3 Power Consumption Base station (display console) : 1 x AA Alkaline or Lithium batteries (not included) Remote sensor : 2 x AA 1.2V LSD type NI-MH batteries (included) Solar panel for backup power Note: 1. Battery type for charging: 2 x AA 1.2V NI-MH batteries(battery life: 3 weeks) 2. It's recommended to recharge the outdoor sensor every two week. 3. Charge time: 3h (The blue LED indicator will light when in charge and be off when full charged) 4.
10. FCC Statement Statement according to FCC part 15.19: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1.This device may not cause harmful interference. 2.This device must accept any interference received, including interference that may cause undesired operation. Statement according to FCC part 15.21: Any changes or modifications not expressly approved by this company could void the user's authority to operate the equipment.
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
11. Warranty Information We disclaim any responsibility for any technical error or printing error, or their consequences. All trademarks and patents are recognized. We provide a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and only to the original purchaser of this product.